EN 13302:2018
(Main)Bitumen and bituminous binders - Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus
Bitumen and bituminous binders - Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus
This document specifies a method for the determination of the dynamic viscosity of a variety of bituminous binders: modified and unmodified bituminous binders, bituminous emulsions, cut-back and fluxed bituminous binders, by means of a rotating spindle apparatus (a coaxial viscometer).
Standard application temperatures are quoted, although the dynamic viscosity can be measured at other temperatures if required. Similarly, measurements at standard values of shear rate can be replaced or complemented by measurements at additional shear rates if required.
WARNING - The use of this document may involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität von bitumenhaltigem Bindemittel mit einem Viskosimeter mit rotierender Spindel
Dieses Dokument legt ein Verfahren zur Bestimmung der dynamischen Viskosität mehrerer Arten von bitumenhaltigen Bindemitteln mithilfe eines Gerätes mit rotierender Spindel (ein Koaxialviskosimeter) fest: zu den betreffenden Bindemitteln gehören modifizierte und nicht modifizierte bitumenhaltige Bindemittel, Bitumenemulsionen sowie verschnittene und gefluxte bitumenhaltige Bindemittel.
Es sind Standard-Anwendungstemperaturen angegeben, obgleich die dynamische Viskosität bei Bedarf auch bei anderen Temperaturen gemessen werden kann. In entsprechender Weise können die Messungen bei Standardwerten der Schergeschwindigkeit ersetzt werden oder durch Messungen bei zusätzlichen Schergeschwindigkeiten ergänzt werden, falls gefordert.
WARNUNG - Die Anwendung dieses Dokuments kann die Anwendung gefährlicher Stoffe, Arbeitsgänge und Geräte mit sich bringen. Dieses Dokument beansprucht nicht, alle damit verbundenen Sicherheitsprobleme zu behandeln. Es liegt in der Verantwortung des Anwenders dieses Dokuments, vor ihrer Anwendung geeignete Maßnahmen für die Sicherheit und den Gesundheitsschutz des Personals zu ergreifen, und dafür Sorge zu tragen, dass behördliche und gesetzliche Maßnahmen eingehalten werden.
Bitumes et liants bitumineux - Détermination de la viscosité dynamique des liants bitumineux à l'aide d'un viscosimètre tournant
Le présent document prescrit une méthode de détermination de la viscosité dynamique de différents liants bitumineux modifiés et non-modifiés, d'émulsions bitumineuses, de liants fluidifiés et fluxés au moyen d’un viscosimètre à mobile tournant (viscosimètre coaxial).
Des températures de référence sont citées dans la présente norme, cependant la viscosité dynamique peut être mesurée à d’autres températures si cela est exigé. De manière analogue, les mesures à des valeurs de référence de cisaillement peuvent être remplacées ou complétées par des mesures à des taux de cisaillement différents si cela est exigé.
AVERTISSEMENT - L'utilisation du présent document implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. Le présent document n'est pas censé aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de ce document de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.
Bitumen in bitumenska veziva - Določanje dinamične viskoznosti bitumenskih veziv z uporabo rotacijskega viskozimetra
Ta evropski standard določa metodo za opredelitev dinamične viskoznosti različnih bitumenskih veziv: modificiranih in nemodificiranih bitumenskih veziv, bitumenskih emulzij ter rezanih in fluksiranih bitumenskih veziv s pomočjo koaksialnega viskozimetra.
Navedene so standardne temperature nanašanja, čeprav je dinamična viskoznost mogoče meriti tudi pri drugih temperaturah, če je to potrebno. Tudi viskoznost je navedena pri standardnih strižni hitrosti, čeprav se po potrebi lahko izvedejo dodatni ukrepi pri različnih strižnih hitrostih.
OPOZORILO – Pri uporabi tega standarda so lahko prisotni nevarni materiali, postopki in oprema. Ta standard ne obravnava vseh varnostnih težav, ki se nanašajo na njegovo uporabo. Za vzpostavitev ustreznih varnostnih in zdravstvenih praks ter za določitev uporabnosti regulativnih omejitev pred uporabo je odgovoren uporabnik tega standarda.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WXPHQVNLKBitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität von bitumenhaltigem Bindemittel mit einem Viskosimeter mit rotierender SpindelBitumes et liants bitumineux - Détermination de la viscosité dynamique des liants bituminuex à l'aide d'un viscosimètre tournantBitumen and bituminous binders - Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 13302:2018SIST EN 13302:2018en,fr,de01-oktober-2018SIST EN 13302:2018SLOVENSKI
STANDARDSIST EN 13302:20101DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13302
June
t r s z ICS
y wä s v râ
{ sä s r rä w r Supersedes EN
s u u r tã t r s rEnglish Version
Bitumen and bituminous binders æ Determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus Bitumes et liants bitumineux æ Détermination de la viscosité dynamique des liants bitumineux à l 5aide d 5un viscosimètre tournant
Bitumen und bitumenhaltige Bindemittel æ Bestimmung der dynamischen Viskosität von bitumenhaltigem Bindemittel mit einem Viskosimeter mit rotierender Spindel This European Standard was approved by CEN on
s w February
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u u r tã t r s z ESIST EN 13302:2018
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1 shear stress force acting tangentially to a surface divided by the area of the surface Note 1 to entry:
«2), kilogram per metre per square second
«1 „ s «2) or Pascal (Pa). 3.2 shear rate velocity gradient in a flowing fluid perpendicular to the stress Note 1 to entry: Shear rate is expressed in units per second (s «1). Note 2 to entry: The shear rate calculation depends upon the viscometer geometry. This should be mentioned by the viscometer manufacturer. SIST EN 13302:2018
1 s «1 to 104 s «1 — Range of dynamic viscosities:
10 «2 Pa „ s to
s r6 Pa „ s In order to cover all product types mentioned in the Scope (Clause 1), under the most usual test conditions, this standard requires rotational viscometer(s) with sample containers and rotating spindles allowing following minimum capabilities: — Range of shear rate:
1 s «1 to 200 s «1 — Range of dynamic viscosities:
10 «2 Pa „ s to
s r3 Pa „ s NOTE 1 For rotating cylinders, the following conditions give an indication of correct measuring geometry: — Ratio of the radius: R2/R1
· 1,1 (reference to Figure 1); — Difference between the radius R2 – R1 = 1 mm to 6 mm. NOTE 2 Typical test temperatures are 40 °C for bituminous emulsions, 60 °C to 90 °C for cut-backs and fluxed bitumens, 60 °C to 200 °C for paving grade or polymer modified bituminous binders, 90°C to 230 °C for oxidized grades. For any given spindle and sample container combination, the operating instructions of the equipment shall allow the operator to select the adequate rotation speed so as to obtain a desired shear rate. SIST EN 13302:2018
Key 1 sample container 2 spindle 3 thickness of sample being measured 4 sample under test R1 spindle radius R2 inner radius of the sample container Figure 1 — Rotational viscometer (principle) 5.2 Appropriate spindle(s), a spindle, or set of spindles, appropriate for the equipment, that will allow, for the materials to be tested and each specific test condition, dynamic viscosities to be measured with an accuracy close to ± 2 % and at least equal to ± 5 %. If achievable accuracy is not known from the information given by the manufacturer of the equipment, the spindles should be selected so as to obtain dynamic viscosity readings under torsion torque values which are between 10 % and 90 % of the maximum possible torsion torque of the spindle for the chosen test conditions. Whenever possible, to get a maximum of accuracy, the spindle should always be selected so as to obtain dynamic viscosity readings under torsion torque values which are in the upper working range for the chosen test conditions. For low viscosity materials (typically, for viscosi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.