prEN ISO 22553-1

SLOVENSKI STANDARD
oSIST prEN ISO 22553-1:2020
01-september-2020

Barve in laki - Nanašanje premazov z elektrodepozicijo - 1. del: Slovar (ISO 22553-

Paints and varnishes - Electro-deposition coatings - Part 1: Vocabulary (ISO 22553-

Peintures et vernis - Peintures d'électrodéposition - Partie 1: Vocabulaire (ISO 22553-

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Abbreviated terms .............................................................................................................................................................................................. 5

Annex A (informative) Test methods for e-coats ...................................................................................................................................... 6

Bibliography ................................................................................................................................................................................................................................ 7

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

Any trade name used in this document is information given for the convenience of users and does not

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso

This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee

Any feedback or questions on this document should be directed to the user’s national standards body. A

During the electro-deposition coating process, the non-volatile matter content from water-thinnable

electro-deposition coating materials is deposited on the workpiece caused by an electrophoretic

process. During that process, the areas on the inside as well as on the outside of the workpiece,

including all cavities, are reached. Depending on whether the workpiece is used as cathode or anode,

it is distinguished between cathodic or anodic deposition. The cathodic electro-deposition coating

Figure 1 — Example of a deposition processes during cathodic electro-deposition coating

With the combination of binder, pigment and deposition process, a very resistant coating is generated

on the workpiece after hardening, which significantly contributes to the corrosion protection in interior

The electric properties of the material are also significant for the electric power consumption of the

Since the e-coat is jointly responsible for the total appearance of the coating system, a good run of the

Consequently, for extensive corrosion protection and for sealing the workpiece, an additional

Inside the e-coat tanks, there is a possibility of bacterial contamination due to the dragged-in material

This document specifies terms and definitions for electro-deposition coatings. The subsequent parts of

the ISO 22553 series specify methods for the characterization of electro-deposition coatings and test