EN ISO 18526-4:2020
(Main)Eye and face protection - Test methods - Part 4: Headforms (ISO 18526-4:2020)
Eye and face protection - Test methods - Part 4: Headforms (ISO 18526-4:2020)
This document specifies the dimensions and tolerances of the headforms used for the testing of eye and face protectors.
Additional information is given for:
— anthropometric measurement methods;
— anthropometric data for head and face dimensions;
— human test panels.
Augen- und Gesichtsschutz - Prüfverfahren - Teil 4 Prüfköpfe (ISO 18526-4:2020)
Dieses Dokument legt die Maße und Toleranzen der zur Prüfung von Augen- und Gesichtsschutzgeräten zu verwendenden Prüfköpfe fest.
Zusätzlich enthält es Informationen zu:
— anthropometrischen Messverfahren;
— anthropometrischen Daten zu Kopf- und Gesichtsmaßen;
— Gruppen von Versuchspersonen.
Protection des yeux et du visage - Méthodes d'essai - Partie 4: Fausses têtes (ISO 18526-4:2020)
Le présent document spécifie les dimensions et les tolérances applicables aux fausses têtes utilisées pour les essais des protecteurs des yeux et du visage.
Des informations supplémentaires sont données pour:
— les méthodes de mesure anthropométrique;
— les données anthropométriques pour les dimensions de la tête et du visage;
— les panels d'essai humains.
Varovanje oči in obraza - Preskusne metode - 4. del: Modeli glav za preskušanje (ISO 18526-4:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2020
Varovanje oči in obraza - Preskusne metode - 4. del: Modeli glav za preskušanje
(ISO 18526-4:2020)
Eye and face protection - Test methods - Part 4: Headforms (ISO 18526-4:2020)
Augen- und Gesichtsschutz - Prüfverfahren - Teil 4 Prüfköpfe (ISO 18526-4:2020)
Protection des yeux et du visage - Méthodes d'essai - Partie 4: Fausses têtes (ISO
18526-4:2020)
Ta slovenski standard je istoveten z: EN ISO 18526-4:2020
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 18526-4
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 13.340.20
English Version
Eye and face protection - Test methods - Part 4: Headforms
(ISO 18526-4:2020)
Protection des yeux et du visage - Méthodes d'essai - Augen- und Gesichtsschutz - Prüfverfahren - Teil 4
Partie 4: Fausses têtes (ISO 18526-4:2020) Prüfköpfe (ISO 18526-4:2020)
This European Standard was approved by CEN on 25 January 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18526-4:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 18526-4:2020) has been prepared by Technical Committee ISO/TC 94
"Personal safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC
85 “Eye protective equipment” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 18526-4:2020 has been approved by CEN as EN ISO 18526-4:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 18526-4
First edition
2020-02
Eye and face protection — Test
methods —
Part 4:
Headforms
Protection des yeux et du visage — Méthodes d'essai —
Partie 4: Fausses têtes
Reference number
ISO 18526-4:2020(E)
©
ISO 2020
ISO 18526-4:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 18526-4:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Headforms . 1
4.1 Classification of adult headforms. 1
4.2 Reference distances and dimensions of adult headforms . 7
4.3 Classification and dimensions of children headforms .10
4.3.1 Type1 headforms .10
4.3.2 Type 2 headforms .10
Annex A (informative) Anthropometric measurements .11
Annex B (informative) Anthropometric data for head and face dimensions .12
Bibliography .17
ISO 18526-4:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by ISO/TC 94, Personal safety — Personal protective equipment,
Subcommittee SC 6, Eye and face protection.
A list of all parts in the ISO 18526 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
ISO 18526-4:2020(E)
Introduction
The family of documents comprised of the ISO 16321 series, the ISO 18526 series and the ISO 18527
series was developed in response to the worldwide stakeholders' demand for minimum requirements
and test methods for eye and face protectors traded internationally. ISO 4007 gives the terms and
definitions for all the various product types. The test methods are given in the ISO 18526 series, while
the requirements for occupational eye and face protectors are given in the ISO 16321 series. Eye
protectors for specific sports are mostly dealt with by the ISO 18527 series. A guidance document,
ISO 19734, for the selection, use and maintenance of eye and face protectors is under preparation.
The basic anatomical requirements of the users of eye and face protection are to be considered when
selecting an appropriate size of protector for comfortable and functional use. This document provides
the anthropometric and biomechanical data required to prepare headforms used for the testing of
protectors. The headform dimensions (series 1 and 2) are based on measurements of humans by the
USA's National Institute of Occupational Safety and Health (NIOSH), which is part of the Centers for
Disease Control and Prevention.
This document provides headform dimensions based on measurements of humans. Further
information is given in Annex A and Annex B, which, together with Figure 3, are reproduced with
NIOSH's and the authors' permission. Figures 2 and 3 show the headforms that are slightly modified to
show better eye detail.
INTERNATIONAL STANDARD ISO 18526-4:2020(E)
Eye and face protection — Test methods —
Part 4:
Headforms
1 Scope
This document specifies the dimensions and tolerances of the headforms used for the testing of eye and
face protectors.
Additional information is given for:
— anthropometric measurement methods;
— anthropometric data for head and face dimensions;
— human test panels.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 4007, Personal protective equipment — Eye and face protection — Vocabulary
CSA Z262.6:2014, Specifications for facially featured headforms
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4007 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Headforms
4.1 Classification of adult headforms
Six different sizes of headforms are used for testing as given in Table 1.
Table 1 — Classification of headforms for eye and face protectors
Small Medium Large
1-S 1-M 1-L
2-S 2-M 2-L
Statistically these six headforms cover approximately 95 % of the population included in this document.
Annex A and Annex B provide detailed information on the data collection and the human populations
ISO 18526-4:2020(E)
that the data is measured from. The information in Annex A and Annex B are from References [2][3]
[15][16].
Examples of the headforms are given in Figures 1 and 2. The individual figures are not to the same scale
as each other, so for accurate details use the CAD files.
a)
2 © ISO 2020 – All rights reserved
--------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.