EN 14411:2006

Ceramic tiles - Definitions, classification, characteristics and marking

This European Standard defines and gives terms, specifies requirements and marking criteria for ceramic tiles (produced by extrusion and dry-pressing techniques) of the best commercial quality (first quality).
Tiles not of first commercial quality are also covered following the provisions of Annex Q.
This European Standard does not cover tiles made by other than the normal processes of extrusion or dry-pressing nor decorative accessories or trim (such as edges, corners, skirting, capping, coves, beads, steps, curved tiles and other accessory pieces) or mosaics (i.e. any piece that can fit into a 7 cm  7 cm area, see custom nomenclature).
NOTE   EN ISO 10545 describes the test procedures required to determine the product characteristics listed in
this European Standard. EN ISO 10545 is divided into parts, each describing a specific test procedure or related matter.

Keramische Fliesen und Platten - Begriffe, Klassifizierung, Gütemerkmale und Kennzeichnung

Diese Europäische Norm legt Begriffe für (durch Strangpress  und Trockenpresstechniken hergestellte) keramische Fliesen und Platten der ersten handelsüblichen Güteklasse sowie die entsprechenden Anfor¬derungen und Kennzeichnungskriterien fest.
Fliesen und Platten, die nicht der ersten handelsüblichen Güteklasse entsprechen, sind nach den Vorgaben von Anhang Q ebenfalls einbezogen.
Diese Europäische Norm gilt weder für Fliesen und Platten, die durch andere als die üblichen Strang¬press  oder Trockenpressprozesse hergestellt wurden, noch für dekoratives Zubehör und Verzierungen (wie zum Beispiel Kanten, Ecken, Sockel, Wölbungen, Kehlungen, Bördelränder, Stufen, gekrümmte Fliesen/ Platten und weiteres Zubehör) und Mosaiks (d. h. Teile, die in eine Fläche von 7 cm  7 cm hineinpassen, siehe Handelsnomenklatur).
ANMERKUNG   EN ISO 10545 beschreibt die Prüfverfahren, die erforderlich sind, um die in dieser Europäischen Norm aufgeführten Produktmerkmale zu bestimmen. EN ISO 10545 besteht aus mehreren Teilen, von denen jeder Teil ein bestimmtes Prüfverfahren oder ein damit zusammenhängendes Phänomen beschreibt.

Carreaux céramiques - Définitions, classification, caractéristiques et marquage

La présente Norme européenne définit et fixe les termes, les exigences et les critères de marquage des carreaux céramiques (produits à l’aide de techniques d’étirage et de pressage à sec) de premier choix.
Les carreaux qui ne sont pas de premier choix d’un point de vue commercial sont également couverts par les dispositions de l’Annexe Q.
La présente Norme européenne couvre uniquement les carreaux fabriqués par étirage ou pressage à sec. Elle ne concerne ni les accessoires décoratifs (cabochons, frises), ni les pièces spéciales (telles que marches, nez de marche, plinthes, angles), ni les mosaïques (c’est-à-dire aucune pièce qui peut rentrer dans une surface de (7  7) cm, voir la nomenclature).
NOTE   L'EN ISO 10545 décrit les modes opératoires d'essai permettant de déterminer les caractéristiques des produits figurant dans la présente Norme européenne. L'EN ISO 10545 est divisée en plusieurs parties, chacune décrivant un mode opératoire d'essai particulier ou un point en rapport avec un mode opératoire.

Keramične ploščice - Definicije, razvrstitev, lastnosti in označevanje

General Information

• Status: Withdrawn
• Publication Date: 19-Dec-2006
• Withdrawal Date: 09-Oct-2012
• ICS: 91.100.25 - Terracotta building products
• Technical Committee: CEN/TC 67 - Ceramic tiles
• Drafting Committee: CEN/TC 67 - Ceramic tiles
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 10-Oct-2012
• Completion Date: 10-Oct-2012
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/119 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on floorings
• Ref Project: SIST EN 14411:2007 - Ceramic tiles - Definitions, classification, characteristics and marking

Relations

• Replaced By: EN 14411:2012 - Ceramic tiles - Definitions, classification, characteristics, evaluation of conformity and marking
• Effective Date: 08-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ceramic tiles - Definitions, classification, characteristics and markingYDQMHCarreaux céramiques - Définitions, classification, caractéristiques et marquageKeramische Fliesen und Platten - Begriffe, Klassifizierung, Gütemerkmale und KennzeichnungTa slovenski standard je istoveten z:EN 14411:2006SIST EN 14411:2007en91.100.23Ceramic tilesICS:SIST EN 14411:20041DGRPHãþDSLOVENSKI
STANDARDSIST EN 14411:200701-marec-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14411December 2006ICS 91.100.25Supersedes EN 14411:2003
English VersionCeramic tiles - Definitions, classification, characteristics andmarkingCarreaux et dalles céramiques - Définitions, classification,caractéristiques et marquageKeramische Fliesen und Platten - Begriffe, Klassifizierung,Gütemerkmale und KennzeichnungThis European Standard was approved by CEN on 13 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14411:2006: E

Extruded ceramic tiles 0,5 < E ≤≤≤≤ 3 % Group AIb.16 A.1 Requirements.16 Annex B (normative)
Extruded ceramic tiles 3 % < E ≤≤≤≤ 6 % Group AIIa — Part 1.19 B.1 Requirements.19 Annex C (normative)
Extruded ceramic tiles 3 % < E ≤≤≤≤ 6 % Group AIIa — Part 2.22 C.1 Requirements.22 Annex D (normative)
Extruded ceramic tiles 6 % < E ≤≤≤≤ 10 % Group AIIb — Part 1.25 D.1 Requirements.25 Annex E (normative)
Extruded ceramic tiles 6 % < E ≤≤≤≤ 10 % Group AIIb — Part 2.28 E.1 Requirements.28 Annex F (normative)
Extruded ceramic tiles E > 10 % Group AIII.31 F.1 Requirements.31 Annex G (normative)
Dry-pressed ceramic tiles with low water absorption E ≤≤≤≤ 0,5 % Group BIa.34 G.1 Requirements.34 Annex H (normative)
Dry-pressed ceramic tiles with low water absorption 0,5 % < E ≤≤≤≤ 3 % Group BIb.37 H.1 Requirements.37 Annex J (normative)
Dry-pressed ceramic tiles 3 % <<<
Dry-pressed ceramic tiles 6 % < E ≤≤≤≤ 10 % Group BIIb.43 K.1 Requirements.43 Annex L (normative)
Dry-pressed ceramic tiles E > 10 % Group BIII.46 L.1 Requirements.46 Annex M (normative)
Extruded ceramic tiles with low water absorption E ≤≤≤≤
0,5 % Group AIa.49 M.1 Requirements.49 Annex N (informative)
Classification of glazed tiles for floors according to their abrasion resistance.52 Annex P (informative)
Test methods.53 Annex Q (normative)
Additional European requirements on tiles.54 Q.1 General.54 Q.2 Release of cadmium.54 Q.3 Release of lead.54 Annex R (informative)
Symbols for intended use.55 ZA.1 Scope and general.57 ZA.2 Procedures for the attestation of conformity of products.61 ZA.2.1 Procedures for the attestation of conformity of flooring.61 ZA.2.2 Procedures for the attestation of conformity of wall and ceiling finishes.61 ZA.3 CE marking and labelling.62 ZA.3.1 CE marking.62 ZA.3.2 Examples of reference model for the marking and labelling.63 ZA.4 EC Declaration of conformity.66 Bibliography.67

this European Standard. EN ISO 10545 is divided into parts, each describing a specific test procedure or related matter. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12004, Adhesives for tiles — Definitions and specifications EN ISO 10545-1, Ceramic tiles — Part 1: Sampling and basis for acceptance (ISO 10545-1:1995) EN ISO 10545-2, Ceramic tiles — Part 2: Determination of dimensions and surface quality (ISO 10545-2:1995, including Technical Corrigendum 1:1997) EN ISO 10545-3, Ceramic tiles — Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density (ISO 10545-3:1995, including Technical Corrigendum 1:1997) EN ISO 10545-4, Ceramic tiles — Part 4: Determination of modulus of rupture and breaking strength (ISO 10545-4:1995) EN ISO 10545-5, Ceramic tiles — Part 5: Determination of impact resistance by measurement of coefficient of restitution (ISO 10545-5:1996, including Technical Corrigendum 1:1996) EN ISO 10545-6, Ceramic tiles — Part 6: Determination of resistance to deep abrasion for unglazed tiles (ISO 10545-6:1995) EN ISO 10545-7, Ceramic tiles — Part 7: Determination of resistance to surface abrasion for glazed tiles (ISO 10545-7:1996) EN ISO 10545-8, Ceramic tiles — Part 8: Determination of linear thermal expansion (ISO 10545-8:1994) EN ISO 10545-9, Ceramic tiles — Part 9: Determination of
...