EN ISO 14373:2015
(Main)Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015)
Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015)
ISO 14373:2015 specifies requirements for resistance spot welding in the fabrication of assemblies of uncoated and metallic coated low carbon steel, comprising two or three sheets of metal, where the maximum single sheet thickness of components to be welded is within the range 0,4 mm to 3 mm, for the following materials: uncoated steels; hot-dip zinc or iron-zinc alloy (galvannealed) coated steel; electrolytic zinc, zinc-iron, or zinc-nickel coated steel; aluminium coated steel; zinc-aluminium coated steel. It is applicable to welding of sheets of the same or dissimilar thickness, where the thickness ratio is less than or equal to 3:1. It applies to the welding of three thicknesses, where the total thickness is less than or equal to 9 mm.
Welding with the following types of equipment is within its scope: pedestal welding equipment; gun welders; automatic welding equipment where the components are fed by robots or automatic feeding equipment; multi welders; robotic welders. It also gives information, for guidance only, on appropriate welding equipment on spot welding conditions.
The welding of organic coated or primer coated steels is not within its scope.
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen mit oder ohne metallischem Überzug (ISO 14373:2015)
Diese Internationale Norm legt die Anforderungen an das Widerstandspunktschweißen an Bauteilen aus niedriglegiertem Stahl mit oder ohne metallischem Überzug fest, die aus zwei oder drei verschiedenen Blechdicken bestehen können, wobei die maximale Dicke eines Einzelbleches der zu schweißenden Bauteile im Bereich von 0,4 mm bis 3 mm aus folgenden Werkstoffen liegt:
- Stahl ohne Überzug;
- Stahl mit Feuerverzinkung oder Fe Zn Legierung (Galvannealed);
- Stahl mit elektrolytisch aufgebrachtem Zn oder Zn Ni Überzug;
- Stahl mit Aluminiumüberzug;
- Stahl mit Zn Al Legierungsüberzug.
Diese Internationale Norm gilt für das Schweißen von Blechen oder Platten gleicher oder unterschiedlicher Dicke mit einem Dickenverhältnis von nicht mehr als 3:1. Sie gilt auch für die Dreiblechschweißung mit einer Gesamtdicke von bis zu 9 mm.
Die folgenden Schweißeinrichtungen liegen im Anwendungsbereich dieser Internationalen Norm:
a) Ständerschweißmaschinen;
b) Schweißpistolen;
c) automatische Schweißeinrichtungen, bei denen die Bauteile durch Roboter oder automatische Zuführungen zugeführt werden;
d) Vielpunktschweißanlagen;
e) Roboterschweißanlagen.
Anhang A enthält Angaben über geeignete Schweißeinrichtungen und Anhang B informiert über die Punktschweißbedingungen. Diese Informationen dienen jedoch nur als Anhalt. In Abhängigkeit von den Fertigungsbedingungen, der Schweißeinrichtung, den Eigenschaften des Sekundärkreises, dem Elektrodenwerkstoff und der Elektrodengeometrie sind gegebenenfalls Anpassungen erforderlich. Falls eine entsprechende Anwendungsnorm hierzu existiert, können weiterführende Informationen daraus entnommen werden.
Das Schweißen von organisch oder mit Primern beschichteten Stählen liegt nicht im Anwendungsbereich dieser Internationalen Norm.
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas carbone revêtus et non revêtus (ISO 14373:2015)
L'ISO 14373:2015 spécifie les exigences relatives au soudage par résistance par points pour la fabrication d'assemblages en acier à bas carbone revêtu ou non revêtu avec deux ou trois épaisseurs de métal, l'épaisseur maximale d'une tôle simple constituant les pièces à souder étant comprise entre 0,4 mm et 3 mm pour les matériaux suivants: aciers non revêtus; acier galvanisé à chaud ou revêtu d'un alliage de fer-zinc (recuit par galvanisation); acier avec revêtement électrolytique de zinc, zinc-fer ou zinc-nickel; acier revêtu d'aluminium; acier revêtu de zinc-aluminium. Elle s'applique au soudage de tôles présentant une épaisseur similaire ou différente, et dont le rapport entre les épaisseurs est inférieur ou égal à 3:1. Elle s'applique au soudage de trois épaisseurs, dont l'épaisseur totale est inférieure ou égale à 9 mm.
Elle concerne le soudage réalisé avec les types de matériels suivants: machine de soudage avec commande au pied; machines à souder mobiles (au pistolet); matériel de soudage automatique avec lequel les composants sont mis en place par des robots ou des appareils d'alimentation automatique; machines à souder multi-points; robots de soudage. Elle donne des informations sur le matériel de soudage approprié et sur les conditions de soudage par points. Ces renseignements ne sont fournis qu'à titre informatif.
Elle ne couvre pas le soudage d'aciers revêtus de produit organique ou d'apprêt (primaire).
Uporovno varjenje - Postopek točkovnega varjenja neprevlečenih in prevlečenih maloogljičnih jekel (ISO 14373:2015)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2015
1DGRPHãþD
SIST EN ISO 14373:2007
8SRURYQRYDUMHQMH3RVWRSHNWRþNRYQHJDYDUMHQMDQHSUHYOHþHQLKLQSUHYOHþHQLK
PDORRJOMLþQLKMHNHO,62
Resistance welding - Procedure for spot welding of uncoated and coated low carbon
steels (ISO 14373:2015)
Widerstandsschweißen - Verfahren zum Punktschweißen von niedriglegierten Stählen
mit oder ohne metallischem Überzug (ISO 14373:2015)
Soudage par résistance - Mode opératoire pour le soudage par points des aciers à bas
carbone revêtus et non revêtus (ISO 14373:2015)
Ta slovenski standard je istoveten z: EN ISO 14373:2015
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14373
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 25.160.10 Supersedes EN ISO 14373:2007
English Version
Resistance welding - Procedure for spot welding of uncoated
and coated low carbon steels (ISO 14373:2015)
Soudage par résistance - Mode opératoire pour le soudage Widerstandsschweißen - Verfahren zum Punktschweißen
par points des aciers à bas carbone revêtus et non revêtus von niedriglegierten Stählen mit oder ohne metallischem
(ISO 14373:2015) Überzug (ISO 14373:2015)
This European Standard was approved by CEN on 3 January 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14373:2015 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 14373:2015) has been prepared by IIW “International Institute of Welding“ in
collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14373:2007.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14373:2015 has been approved by CEN as EN ISO 14373:2015 without any modification.
INTERNATIONAL ISO
STANDARD 14373
Second edition
2015-03-15
Resistance welding — Procedure for
spot welding of uncoated and coated
low carbon steels
Soudage par résistance — Mode opératoire pour le soudage par
points des aciers à bas carbone revêtus et non revêtus
Reference number
ISO 14373:2015(E)
©
ISO 2015
ISO 14373:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
ISO 14373:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 2
5 Materials . 3
5.1 Form . 3
5.2 Steel grades . 3
6 Surface conditions . 3
7 Edge conditions, form of component, and weld spacing . 3
8 Electrodes . 3
8.1 Materials . 3
8.2 Dimensions . 3
8.3 Cooling of electrodes . 5
9 Weld assessment . 6
9.1 General . 6
9.2 Weldability tests . 6
9.3 Production tests . 6
9.4 Frequency of testing . 6
10 Weld quality requirements . 7
10.1 Weld diameter . 7
10.2 Weld penetration and indentation . 7
10.3 Failure description of welds . 7
10.4 Tensile shear strength . 7
10.5 Weld appearance . 8
10.5.1 Surface condition . 8
10.5.2 Distortion . 8
11 Multi-weld arrays . 9
Annex A (informative) Recommendations for spot welding equipment .11
Annex B (informative) Typical spot welding conditions .12
Annex C (informative) Partial list of steel types applicable to this International Standard .14
Bibliography .15
ISO 14373:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
ISO 14373 was prepared by IIW, International Institute of Welding, Commission III. Requests for official
interpretations of any aspect of this International Standard should be directed to the ISO Central
Secretariat, who will for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.