EN ISO 10426-4:2004

Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)

ISO 10426-4:2004 defines the methods for the generation and testing of foamed cement slurries and their corresponding unfoamed base cement slurries at atmospheric pressure.

Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von Tiefbohrungen - Teil 4: Vorbereitung und Prüfung von Schaumzementbrühen unter atmosphärischen Bedingungen (ISO 10426-4:2004)

Industrie du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des puits - Partie 4: Préparation et essais en conditions ambiantes des laitiers de ciment mousse (ISO 10426-4:2004)

L'ISO 10426-4:2004 définit les méthodes de préparation et d'essais, à la pression atmosphérique, des laitiers de ciment mousse ainsi que des laitiers de ciment de base sans mousse correspondants.

Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za cementiranje vrtin - 4. del: Priprava in preskušanje penjenih cementnih past pri atmosferskem tlaku (ISO 10426-4:2004)

General Information

• Status: Published
• Publication Date: 21-Dec-2004
• Withdrawal Date: 29-Jun-2005
• ICS: 75.020 - Extraction and processing of petroleum and natural gas
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 14-Mar-2009
• Completion Date: 14-Mar-2009
• Ref Project: SIST EN ISO 10426-4:2005 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)

Relations

• Revised: FprEN ISO 10426-4 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO/FDIS 10426-4:2019)
• Effective Date: 04-Oct-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2005
Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za
cementiranje vrtin - 4. del: Priprava in preskušanje penjenih cementnih past pri
atmosferskem tlaku (ISO 10426-4:2004)
Petroleum and natural gas industries - Cements and materials for well cementing - Part
4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO
10426-4:2004)
Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von
Tiefbohrungen - Teil 4: Vorbereitung und Prüfung von Schaumzementbrühen unter
atmosphärischen Bedingungen (ISO 10426-4:2004)
Industrie du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des
puits - Partie 4: Préparation et essais en conditions ambiantes des laitiers de ciment
mousse (ISO 10426-4:2004)
Ta slovenski standard je istoveten z: EN ISO 10426-4:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10426-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 91.100.10; 75.020
English version
Petroleum and natural gas industries - Cements and materials
for well cementing - Part 4: Preparation and testing of foamed
cement slurries at atmospheric pressure (ISO 10426-4:2004)
Industrie du pétrole et du gaz naturel - Ciments et Erdöl- und Erdgasindustrie - Zemente und Materialen für
matériaux pour la cimentation des puits - Partie 4: die Zementation von Tiefbohrungen - Teil 4: Vorbereitung
Préparation et essais en conditions ambiantes des laitiers und Prüfung von Schaumzementbrühen unter
de ciment mousse (ISO 10426-4:2004) atmosphärischen Bedingungen (ISO 10426-4:2004)
This European Standard was approved by CEN on 21 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10426-4:2004: E
worldwide for CEN national Members.

Foreword
The text of ISO 10426-4:2004 has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10426-
4:2004 by Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for
petroleum and natural gas industries" the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2005, and conflicting national
standards shall be withdrawn at the latest by June 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 10426-4:2004 has been approved by CEN as EN ISO 10426-4:2004 without any
modifications.
INTERNATIONAL ISO
STANDARD 10426-4
First edition
2004-03-01
Petroleum and natural gas industries —
Cements and materials for well
cementing —
Part 4:
Preparation and testing of foamed
cement slurries at atmospheric pressure
Industrie du pétrole et du gaz naturel — Ciments et matériaux pour la
cimentation des puits —
Partie 4: Préparation et essais en conditions ambiantes des laitiers de
ciment mousse
Reference number
ISO 10426-4:2004(E)
©
ISO 2004
ISO 10426-4:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved

ISO 10426-4:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Sampling . 1
4 Slurry calculations . 1
5 Apparatus. 5
6 Preparation of base cement slurry. 5
7 Preparation of foamed cement slurry at atmospheric pressure . 6
8 Example calculations for the preparation of foamed cement slurry at atmospheric
pressure . 7
9 Atmospheric testing of foamed cement slurries . 9
10 Determination of other properties of base unfoamed cement slurry . 12
Bibliography . 13

ISO 10426-4:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10426-4 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 3, Drilling and completion fluids,
and well cements.
ISO 10426 consists of the following parts, under the general title Petroleum and natural gas industries —
Cements and materials for well cementing:
 Part 1: Specification
 Part 2: Testing of well cements
 Part 3: Testing of deepwater well cement formulations
 Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure
 Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure
iv © ISO 2004 – All rights reserved

ISO 10426-4:2004(E)
Introduction
Users of this part of ISO 10426 should be aware that further or differing requirements may be needed for
individual applications. This part of ISO 10426 is not intended to inhibit a vendor from offering, or the
purchaser from accepting, alternative equipment or engineering solutions for the individual application. This
may be particularly applicable where there is innovative or developing technology. Where an alternative is
offered, the vendor should identify any variations from this International Standard and provide details.
Cements or cement blends used for foamed cement slurry preparation at atmospheric pressure should be fit
for purpose. Such cements could include well cements of ISO Classes, high alumina cement, or other
speciality cements. The cements and blending materials should conform to appropriate standards. Where
International Standards do not exist, conformance with other appropriate standards should be made.
In this part of ISO 10426, where practical, U.S. Customary units are included in brackets for information.
INTERNATIONAL STANDARD ISO 10426-4:2004(E)

Petroleum and natural gas industries — Cements and materials
for well cementing —
Part 4:
Preparation and testing of foamed cement slurries at
atmospheric pressure
1 Scope
This part of ISO 10426 defines the methods for the generation and testing of foamed cement slurries and their
corresponding unfoamed base cement slurries at atmospheric pressure.
2 Normative references
The following normative document is indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
ISO 10426-2:2003, Petroleum and natural gas industries — Cements and materials for well cementing —
Part 2: Testing of well cements
3 Sampling
3.1 General
Samples of the cement material or cement blend, solid and liquid additives, and water used for mixing are
required to test a foamed cement slurry in accordance with this part of ISO 10426. Accordingly, the best
available sampling technology should be employed to ensure the test materials match as closely as possible
those found at the well site.
3.2 Method
Applicable sampling techniques for the fluids and materials used in foamed cementing operations can be
found in ISO 10426-2:2003, Clause 4. If required, the temperatures of the mix water, cement or cement
blends, and liquid additives may be measured with a thermocouple or thermometer capable of measuring
temperature with an accuracy of ± 2 °C (± 3,5 °F). These temperatures should be recorded. Temperature-
measuring devices shall be calibrated (in the case of a thermocouple) or checked for accuracy (in the case of
a thermometer) annually.
4 Slurry calculations
4.1 Calculation of base cement slurry composition with and without surfactant(s)
The final base cement slurry for preparing a foamed cement slurry contains surfactant(s), which cannot be
added to the base cement slurry for initial mixing. This requires calculation of the relative mass percentage
(mass fraction) of the surfactant(s) in the foamed cement slurry. This is done by taking the total mass of the
ISO 10426-4:2004(E)
surfactant(s) and dividing by the total mass of th
...