EN ISO 5577:2017
(Main)Non-destructive testing - Ultrasonic testing - Vocabulary (ISO 5577:2017)
Non-destructive testing - Ultrasonic testing - Vocabulary (ISO 5577:2017)
ISO 5577:2017 defines the terms used in ultrasonic non-destructive testing and forms a common basis for standards and general use. This document does not cover terms used in ultrasonic testing with phased arrays.
NOTE Terms for phased array ultrasonic testing are defined in EN 16018.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Terminologie (ISO 5577:2017)
Dieses Dokument legt die Begriffe fest, die bei der zerstörungsfreien Ultraschallprüfung verwendet werden, und bildet somit eine gemeinsame Grundlage für Normen und den allgemeinen Gebrauch. Dieses Dokument behandelt keine Begriffe der zerstörungsfreien Prüfung mit phasengesteuerten Arrays.
ANMERKUNG Begriffe für zerstörungsfreie Prüfung mit phasengesteuerten Arrays sind in EN 16018 festgelegt.
Essais non destructifs - Contrôle par ultrasons - Vocabulaire (ISO 5577:2017)
ISO 5577:2017 définit les termes utilisés pour le contrôle non destructif par ultrasons et constitue une base commune pour les normes et l'usage général. Le présent document n'inclut pas les termes utilisés pour le contrôle par ultrasons en multiéléments.
NOTE Les termes applicables au contrôle par ultrasons en multiéléments sont définis dans l'EN 16018.
Neporušitvene preiskave - Preskušanje z ultrazvokom - Slovar (ISO 5577:2017)
Ta mednarodni standard opredeljuje terminologijo, ki se uporablja pri neporušitvenem preskušanju z ultrazvokom in oblikuje skupno podlago za standarde in splošno uporabo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2017
1DGRPHãþD
SIST EN 1330-4:2011
Neporušitvene preiskave - Preskušanje z ultrazvokom - Slovar (ISO 5577:2017)
Non-destructive testing - Ultrasonic testing - Vocabulary (ISO 5577:2017)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Terminologie (ISO 5577:2017)
Essais non destructif - Contrôle par ultrasons - Vocabulaire (ISO 5577:2017)
Ta slovenski standard je istoveten z: EN ISO 5577:2017
ICS:
01.040.19 Preskušanje (Slovarji) Testing (Vocabularies)
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 5577
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2017
EUROPÄISCHE NORM
ICS 01.040.19; 19.100 Supersedes EN 1330-4:2010
English Version
Non-destructive testing - Ultrasonic testing - Vocabulary
(ISO 5577:2017)
Essais non destructif - Contrôle par ultrasons - Zerstörungsfreie Prüfung - Ultraschallprüfung -
Vocabulaire (ISO 5577:2017) Terminologie (ISO 5577:2017)
This European Standard was approved by CEN on 28 December 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5577:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 5577:2017) has been prepared by Technical Committee ISO/TC 135 "Non-
destructive testing" in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall
be withdrawn at the latest by August 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 1330-4:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5577:2017 has been approved by CEN as EN ISO 5577:2017 without any modification.
INTERNATIONAL ISO
STANDARD 5577
Second edition
2017-02
Non-destructive testing — Ultrasonic
testing — Vocabulary
Essais non destructif — Contrôle par ultrasons — Vocabulaire
Reference number
ISO 5577:2017(E)
©
ISO 2017
ISO 5577:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 5577:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms related to frequencies, waves and pulses . 1
3.1 Frequencies . 1
3.2 Waves and pulses . 2
3.3 Types of waves . 4
4 Terms related to sound . 5
4.1 Sound generation and reception . 5
4.2 Sound propagation . 6
4.3 Loss of sound pressure . 9
4.4 Sound waves at interfaces . 9
5 Terms related to test equipment .12
5.1 Instrument .12
5.2 Probes .15
5.3 Combined equipment .20
5.4 Calibration, reference and test blocks .21
6 Terms related to ultrasonic testing .22
6.1 Testing techniques .22
6.2 Test object .26
6.3 Coupling .28
6.4 Reflectors .28
6.5 Signals and indications .29
6.6 Presentations .31
6.7 Location .35
6.8 Evaluation of indications .36
Bibliography .38
ISO 5577:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
ISO 5577 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 138, Non-destructive testing, in collaboration with ISO Technical Committee TC 135, Non-
destructive testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 5577:2000), which has been technically
revised with changes to terms and definitions and structure.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 5577:2017(E)
Non-destructive testing — Ultrasonic testing — Vocabulary
1 Scope
This document defines the terms used in ultrasonic non-destructive testing and forms a common basis
for standards and general use. This document does not cover terms used in ultrasonic testing with
phased arrays.
NOTE Terms for phased array ultrasonic testing are defined in EN 16018.
2 Normative references
There are no normative references in this document.
3 Terms related to frequencies, waves and pulses
For the purposes of this document, the terms and definitions given in this clause and those given in
Clauses 4, 5 and 6 for sound, test equipment and ultrasonic testing apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1 Frequencies
3.1.1
frequency
number of cycles per second
Note 1 to entry: Expressed in Hertz (Hz).
3.1.2
nominal frequency
probe freque
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.