EN 200:2008
(Main)Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
This European Standard specifies:
a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:
1) a supply system of Type 1 (see Figure 1);
2) a supply system of Type 2 (see Figure 2);
b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics of nominal size ½ and ¾ single taps and combination taps;
c) test methods to verify the characteristics.
d) The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.
This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.
Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar].
Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar].
This European Standard applies to sanitary draw-off taps of nominal size ½ and ¾ (PN 10).
The conditions of use and classifications are given in Table 1 but note the comments in Table 2.
Sanitärarmaturen - Auslaufventile und Mischbatterien für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation
Diese Europäische Norm legt Folgendes fest:
a) den Anwendungsbereich für Standventile, Wand-Auslaufventile, Einloch- und Mehrloch-Standbatterien für
die Anwendung in:
1) einem Versorgungssystem vom Typ 1 (siehe Bild 1),
2) einem Versorgungssystem vom Typ 2 (siehe Bild 2);
b) die Maße, die Dichtheit, die Festigkeit unter Innendruck, die hydraulischen Eigenschaften, die
mechanische Festigkeit und Dauerfestigkeit sowie das Geräuschverhalten von Auslaufventilen und
Mischbatterien der Nenngrößen ½ und ¾;
c) die Prüfverfahren, um diese Anforderungen zu überprüfen;
Die in dieser Europäischen Norm beschriebenen Prüfungen sind Typprüfungen (Laborprüfungen) und nicht für
die Fertigungskontrolle vorgesehen.
Diese Europäische Norm gilt für Entnahmearmaturen (Auslaufventile und Mischbatterien) zur Verwendung mit
Sanitärausstattungsgegenständen, die in den der Hygiene dienenden Räumen (Toiletten, Bäder usw.) und in
Küchen installiert werden, d. h. für Badewannen, Waschbecken, Sitzwaschbecken, Duschen und Spülbecken.
Bild 1 zeigt das Versorgungssystem vom Typ 1 mit einem Druckbereich von 0,05 MPa bis 1,0 MPa [(0,5 bar
bis 10 bar)].
Bild 2 zeigt das Versorgungssystem vom Typ 2 mit einem Druckbereich von 0,01 MPa bis 1,0 MPa [(0,1 bar
bis 10 bar)].
Diese Europäische Norm gilt für Sanitärarmaturen der Nenngrößen ½ und ¾ (PN 10).
Die Anwendungsbedingungen und Klassifizierungen sind in Tabelle 1 angegeben. Tabelle 2 zeigt die
Leistungsmerkmale, die beim Einsatz der Armaturen außerhalb des empfohlenen Betriebsbereiches zu
überwachen sind.
Robinetterie sanitaire - Robinets simples et mélangeurs pour les systèmes d'alimentation en eau des types 1 et 2 - Spécifications techniques générales
La présente Norme Européenne spécifie :
a) le champ d’application des robinets simples montés sur paroi horizontale, des robinets simples montés sur paroi verticale, des robinets mélangeurs monotrou et multitrou destinés à être utilisés dans :
1) un système d’alimentation de Type 1 (voir Figure 1) ;
2) un système d’alimentation de Type 2 (voir Figure 2) ;
b) les cotes, les caractéristiques d’étanchéité, de résistance à la pression, de performance hydraulique, de résistance mécanique, d’endurance et les caractéristiques acoustiques des robinets simples et des robinets mélangeurs de dimension nominale ½ et ¾ ;
c) les méthodes d’essai permettant de vérifier ces caractéristiques.
Les essais décrits dans la présente Norme Européenne sont des essais de type (essais en laboratoire) et non des essais de contrôle qualité réalisés en cours de fabrication.
La présente Norme Européenne s’applique aux robinets de puisage (robinets simples et robinets mélangeurs) destinés à l’équipement des appareils sanitaires installés dans les locaux d’hygiène corporelle (toilettes, salles de bain etc.) et dans les cuisines, pour un usage sur les baignoires, lavabos, bidets, douches et éviers, par exemple.
La Figure 1 représente un système d’alimentation de Type 1 dans une plage de pression de (0,05 à 1,0) MPa [(0,5 à 10 bar)].
La Figure 2 représente un système d’alimentation de Type 2 dans une plage de pression de (0,01 à 1,0) MPa [(0,1 à 10 bar)].
La présente Norme Européenne s’applique aux robinets de puisage sanitaires de dimension nominale ½ et ¾ (PN 10).
Les conditions d’utilisation et la classification sont données dans le Tableau 1. Le Tableau 2 fournit les caractéristiques de performance à prendre en compte si le robinet est utilisé en dehors de la plage de fonctionnement recommandée.
Sanitarne armature - Enojne pipe in kombinirane pipe za oskrbo z vodo tipa 1 in tipa 2 - Splošne tehnične zahteve
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitärarmaturen - Auslaufventile und Mischbatterien für Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische SpezifikationRobinetterie sanitaire - Robinets simples et mélangeurs pour les systèmes d'alimentation type 1 et type 2 - Spécifications techniques généralesSanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 200:2008SIST EN 200:2009en,fr,de01-januar-2009SIST EN 200:2009SLOVENSKI
STANDARDSIST EN 200:20051DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 200July 2008ICS 91.140.70Supersedes EN 200:2004
English VersionSanitary tapware - Single taps and combination taps for watersupply systems of type 1 and type 2 - General technicalspecificationRobinetterie sanitaire - Robinets simples et mélangeurspour les systèmes d'alimentation type 1 et type 2 -Spécifications techniques généralesSanitärarmaturen - Auslaufventile und Mischbatterien fürWasserversorgungssysteme vom Typ 1 und Typ 2 -Allgemeine technische SpezifikationThis European Standard was approved by CEN on 15 June 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 200:2008: ESIST EN 200:2009
Contents Page Foreword.5 Introduction.6 1 Scope.7 2 Normative references.11 3 Designation.11 4 Marking and identification.12 5 Materials.13 6 Dimensional characteristics.14 7 Sequence of testing.24 8 Leaktightness characteristics.25 9 Pressure resistance characteristics - mechanical performance under pressure.31 10 Hydraulic characteristics.33 11 Mechanical strength characteristics - torsion test for operating mechanism.36 12 Mechanical endurance characteristics.37 13 Backflow protection.45 14 Acoustic characteristics.45 Annex A (informative)
Pressure take-off tee.47 Bibliography.51
of Type 2.31 Figure 14 - Flow rate test apparatus for taps for Type 2 supply systems.35 Figure 15 - Life test –closing torque vs time.40 Figure 16 - Endurance test rig for divided-outlet swivel spout.45 Figure A.1 - Pressure take-off tee (test rig Type 1 taps).47 Figure A.2 - Schematic examples of pressure take-off tees (test rig Type 1 taps).49
Table.Page Table 1 - Conditions of use/Classifications.8 Table 2 - Performance characteristics to be noted if used outside the recommended operating range.8 Table 3 - Designation.12 Table 4 - Inlet dimensions (Pillar & bib taps, single- & multi-hole combination taps).15 Table 5 - Outlet dimensions (Remote outlets, pillar taps, bib taps, single- and multi-hole combination taps).19 Table 6 - Mounting dimensions (Pillar taps, single- and multi-hole combination taps).22 Table 7 - Test Sequence.25 Table 8 - Summary of tightness tests.30 Table 9 - Summary of pressure resistance characteristic tests.33 Table 10 - Minimum flow rates and test pressures according to application.36 Table 11 - Endurance Test conditions.39 Table 12 - Summary of test conditions for diverters.42 Table 13 - Flow rate classes (EN ISO 3822-4:1997, Annex A).46 Table 14 - Acoustic group.46 Table A.1 - Dimensions of the pressure take-off tee.48
Introduction In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product covered by this European Standard. This European Standard provides no information as to whether the product can be used without restriction in any of the Member States of the EU or EFTA. It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of these products remain in force. This document identifies characteristics and technical requirements for single and combination taps.
the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in: 1) a supply system of Type 1 (see Figure 1); 2) a supply system of Type 2 (see Figure 2); b)
the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics of nominal size ½ and ¾ single taps and combination taps; c)
test methods to verify the characteristics. The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture. This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks. Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar]. Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar]. This European Standard applies to sanitary draw-off taps of nominal size ½ and ¾ (PN 10). The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics to be noted if the tap is used outside the recommended operating range. SIST EN 200:2009
Table 1 — Conditions of use/Classifications Operating range of taps Flow rate classes Acoustics Marking Water supply system Limits Recommended See Table 13 See 14 See 4 Type 1 see Figure 1 Dynamic Pressure > 0,05 Mpa (0,5 bar) Static Pressure ≤ 1,0 Mpa (10,0 bar) Dynamic Pressure (0,1 to 0,5) Mpa [(1.0 to 5,0) bar] see note b) Z ≤ 0,15 l/s A ≤ 0,25 l/s S ≤ 0,33 l/s B ≤ 0,42 l/s C ≤ 0,50 l/s D ≤ 0,63 l/s
Group I -
Group II –
unclassified
for example IA IIC/B
I /- a) II /- a) See Table 10 Type 2 see Figure 2 Dynamic Pressure > 0,01 Mpa (0,1 bar) Static Pressure ≤ 1,0 Mpa (10,0 bar) Dynamic Pressure (0,02 to 0,1) MPa [(0,2 to 1,0) bar] see note b) X ≤ 0,125 l/s Y ≤ 0,250 l/s R d) ≤ 0,125 l/s Hot and
≤ 0,070 l/s Cold see note c) (unclassified) X Y R Temperature ≤ 90 °C < 65 °C
a) Without flow rate class: Taps without interchangeable outlet accessories are tested with the original outlet accessories of the manufacturer and are not marked with a flow rate class. b) Measured at the shower outlet when incorporated. c) The
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.