EN ISO 14692-2:2002
(Main)Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)
ISO 14692-2:2002 gives requirements for the qualification and manufacture of GRP piping and fittings in order to enable the purchase of GRP components with known and consistent properties from any source.
It is applicable to qualification procedures, preferred dimensions, quality programmes, component marking and documentation.
ISO 14692-2:2002 is intended to be read in conjunction with ISO 14692-1.
Erdöl- und Erdgasindustrie - Glasfaserverstärkte Kunstoffrohrleitungen (GFK) - Teil 2: Zulassung und Herstellung (ISO 14692-2:2002)
Industries du pétrole et du gaz naturel - Canalisations en plastique renforcé de verre (PRV) - Partie 2: Conformité aux exigences de performance et fabrication (ISO 14692-2:2002)
L'ISO 14692-2:2002 spécifie les exigences relatives à la qualification et la fabrication des canalisations et raccords en PRV afin de permettre l'achat de composants en PRV en provenance d'une source quelconque dont les propriétés sont connues et constantes.
Elle s'applique aux modes opératoires de qualification, aux dimensions préférées, aux programmes qualité, au marquage des composants et à la documentation.
L'ISO 14692-2:2002 est destinée à être lue conjointement avec l'ISO 14692-1.
Industrija za predelavo nafte in zemeljskega plina - S steklenimi vlakni ojačeni polimerni cevovodi (GRP) - 2. del: Kvalificiranje in proizvodnja (ISO 14692-2:2002)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Erdöl- und Erdgasindustrie - Glasfaserverstärkte Kunstoffrohrleitungen (GFK) - Teil 2: Zulassung und Herstellung (ISO 14692-2:2002)Industries du pétrole et du gaz naturel - Canalisations en plastique renforcé de verre (PRV) - Partie 2: Conformité aux exigences de performance et fabrication (ISO 14692-2:2002)Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)83.140.30Cevi, fitingi in ventili iz polimernih materialovPlastics pipes, fittings and valves75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN ISO 14692-2:2002SIST EN ISO 14692-2:2004en01-maj-2004SIST EN ISO 14692-2:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 14692-2December 2002ICS 75.200; 83.140.30English versionPetroleum and natural gas industries - Glass-reinforced plastics(GRP) piping - Part 2: Qualification and manufacture (ISO14692-2:2002)Industries du pétrole et du gaz naturel - Canalisations enplastique renforcé de verre (PRV) - Partie 2: Conformitéaux exigences de performance et fabrication (ISO 14692-2:2002)This European Standard was approved by CEN on 2 December 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 14692-2:2002 ESIST EN ISO 14692-2:2004
The foreword is susceptible to be amended on reception of the Germanlanguage version. The confirmed or amended foreword, and when appropriate, the normativeannex ZA for the references to international publications with their relevant Europeanpublications will be circulated with the German version.Endorsement noticeThe text of ISO 14692-2:2002 has been approved by CEN as EN ISO 14692-2:2002 without anymodifications.SIST EN ISO 14692-2:2004
Reference numberISO 14692-2:2002(E)© ISO 2002
INTERNATIONAL STANDARD ISO14692-2First edition2002-12-15Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping —Part 2: Qualification and manufacture Industries du pétrole et du gaz naturel — Canalisations en plastique renforcé de verre (PRV) — Partie 2: Conformité aux exigences de performance et fabrication
ISO 14692-2:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2002 — All rights reserved
ISO 14692-2:2002(E) © ISO 2002 — All rights reserved iii Content Page Foreword.v Introduction.vi 1 Scope.1 2 Normative references.1 3 Terms and definitions.3 4 Symbols and abbreviated terms.3 5 Materials of construction and wall thickness limitations.3 5.1 General.3 5.2 Fibre.3 5.3 Resin.3 5.4 Joints.4 5.5 Wall thickness limitations.5 6 Qualification programme.5 6.1 General.5 6.2 Qualification pressure and temperature.6 6.3 Effect of temperature and chemical resistance.16 6.4 Optional qualification requirements.17 6.5 Fire performance.18 6.6 Electrical conductivity and electrostatic dissipative properties.21 6.7 Additional component properties.24 6.8 Component data for quality control baseline.25 7 Preferred dimensions.26 7.1 Nominal diameters.26 7.2 Bend radii.27 7.3 Fitting lengths.27 8 Quality programme for manufacture.27 8.1 General requirements.27 8.2 Quality control equipment.28 8.3 Quality control tests.28 8.4 Quality control records.34 9 Component marking.35 9.1 General.35 9.2 Requirements.35 10 Handling, storage and transportation.36 11 Documentation.36 11.1 General.36 11.2 Purchase order documentation.36 11.3 Qualification documentation.36 11.4 Production quality control documentation.37 11.5 Installation documentation.38 11.6 Published values.38 Annex A (informative)
Examples of component requirements for qualification.41 Annex B (informative)
Pressure qualification test ratios.43 Annex C (normative)
Failure enveloppe.46 SIST EN ISO 14692-2:2004
ISO 14692-2:2002(E) iv © ISO 2002 — All rights reserved Annex D (informative)
Guidance on determination of partial factors A1 and A2 for temperature and chemical resistance.48 Annex E (normative)
Fire endurance testing.50 Annex F (normative)
Modifications to fire reaction test procedures.59 Annex G (normative)
Determination of electrostatic properties of GRP pipe system components.61 Annex H (normative)
Preferred dimensions.72 Annex I (informative)
Example of enquiry sheet.75 Annex J (informative)
Example of qualification summary form.76 Annex K (normative)
Least-square method for calculating the long-term hydrostatic pressure from regression data.78 Bibliography.86
ISO 14692-2:2002(E) © ISO 2002 — All rights reserved v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.