EN 10264-3:2002

Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications

This part of this European Standard defines round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications.
This part of this European Standard refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T).
In addition to the requirements of this part of this European Standard, the requirements of prEN 10264-1 also apply.
It does not apply to steel wire taken from manufactured ropes.
This part of this European Standard specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating.

Stahldraht und Drahterzeugnisse - Stahldraht für Seile - Teil 3: Runder und profilierter Draht aus unlegiertem Stahl für hohe Beanspruchungen

Anwendungsbereich
Dieser Teil dieser Europäischen Norm legt runden und profilierten Draht aus unlegiertem Stahl zur Herstellung von Seilen für Schachtförderanlagen des Bergbaus, Personenbeförderung, Seilbahnen für Personenbeförderung und andere hohe Beanspruchungen fest.
Dieser Teil dieser Europäischen Norm betrifft Runddrähte und drei Arten von Formdrähten: Z-Drähte, Taillen-drähte (H) und Keildrähte (T).
Zusätzlich zu den Anforderungen dieses Teils dieser Europäischen Norm gelten auch die Anforderungen von
prEN 10264-1.
Sie gilt nicht für Stahldrähte aus dem Seil.
Dieser Teil dieser Europäischen Norm trifft zu folgenden Punkten Festlegungen für kaltgezogenen Draht aus unlegiertem Stahl für Seile für hohe Beanspruchungen:
¾ Maßtoleranzen
¾ Mechanische Eigenschaften
¾ Anforderungen an die chemische Zusammensetzung des Stahldrahtes
¾ Anforderungen an den Überzug

Fils et produits tréfilés en acier - Fils pour câbles - Partie 3: Fils ronds et profilés, en acier non allié, pour fortes sollicitations

La présente partie de la présente Norme européenne définit les fils ronds et profilés en acier non allié, pour utilisation dans la fabrication de câbles pour appareils de levage de mines, pour le transport des personnes et les téléphériques, pour le transport de passagers et autres sollicitations élevées.
Cette partie de Norme européenne couvre les fils ronds et 3 types de profilés : clos (Z), mi-clos (H) et profilés trapézoïdaux (T).
En plus des exigences de cette partie de Norme européenne, les exigences de l'EN 10264-1 s'appliquent également.
Elle ne s'applique pas aux fils d'acier prélevés sur les câbles fabriqués.
La présente partie de la présente norme spécifie pour les fils écrouis à froid en acier non allié pour câbles soumis à sollicitations élevées :
¾ les tolérances dimensionnelles ;
¾ les caractéristiques mécaniques ;
¾ les exigences concernant la composition chimique des fils en acier  ;
¾ les conditions auxquelles le revêtement éventuel doit satisfaire.

Jeklena žica in žični izdelki - Jeklena žica za vrvi - 3. del: Okrogla in oblikovana nelegirana jeklena žica za velike obremenitve

General Information

• Status: Withdrawn
• Publication Date: 12-Nov-2002
• Withdrawal Date: 10-Jan-2012
• ICS: 77.140.45 - Non-alloyed steels
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: ECISS/TC 106 - Wire rod and wires
• Drafting Committee: ECISS/TC 30/SC 1 - Wire coatings
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 11-Jan-2012
• Completion Date: 11-Jan-2012
• Ref Project: SIST EN 10264-3:2003 - Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications

Relations

• Replaced By: EN 10264-3:2012 - Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications
• Effective Date: 08-Jun-2022
• Parent: EN 10264-1:2002 - Steel wire and wire products - Steel wire for ropes - Part 1: General requirements
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahldraht und Drahterzeugnisse - Stahldraht für Seile - Teil 3: Runder und profilierter Draht aus unlegiertem Stahl für hohe BeanspruchungenFils et produits tréfilés en acier - Fils pour câbles - Partie 3: Fils ronds et profilés, en acier non allié, pour fortes sollicitationsSteel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains77.140.45Nelegirana jeklaNon-alloyed steelsICS:Ta slovenski standard je istoveten z:EN 10264-3:2002SIST EN 10264-3:2003en01-april-2003SIST EN 10264-3:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10264-3November 2002ICS 77.140.65English versionSteel wire and wire products - Steel wire for ropes - Part 3:Round and shaped non alloyed steel wire for high dutyapplicationsFils et produits tréfilés en acier - Fils pour câbles - Partie 3:Fils ronds et profilés, en acier non allié, pour fortessollicitationsStahldraht und Drahterzeugnisse - Stahldraht für Seile -Teil 3: Runder und profilierter Draht aus unlegiertem Stahlfür hohe BeanspruchungenThis European Standard was approved by CEN on 9 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10264-3:2002 ESIST EN 10264-3:2003

Wire for rope, trapezoidal profile, h = 3,5 mm, class B zinc coated, tensile strength grade 1770 MPa,in accordance with EN 10264-3.Designation: wire for rope EN 10264-3 - T3,5 - B - 1770EXAMPLE 3: H shaped wire for rope h = 3,0 mm, w = 1,8 mm, coated with class A zinc alloy, tensile strength grade1370 MPa, in accordance with EN 10264-3.Designation: wire for rope EN 10264-3 - H – 3,0 ´ 1,8 - A (Zn/Al) - 13704 General conditions of manufactureThe drawn wire shall be manufactured from rod in accordance with EN 10016-1 and EN 10016-2 for ropes for staticapplications, and in accordance with EN 10016-1 and EN 10016-4 for ropes for dynamic applications.The drawn wire shall show no surface defects or internal defects prejudicial to its use.When specified, the drawn wire shall be supplied with a coating applied by a hot dipping or electrolytic method. Thecoatings commonly used are zinc or Zn95/Al5.Unless otherwise specified, the zinc used for coating shall have a purity of 99,9 %. Other zinc alloys may be agreedat the time of enquiry and order.NOTE
If required by the purchaser, the quality of the zinc or zinc alloy used for the coating material (zinc or zinc alloy) shouldbe certified by the manufacturer. Because of the reaction between the base material and coating material, which is inherent tothe process, the composition of the coating on the wire is different to that used in the coating bath.5 Characteristics of the wire5.1 Tensile strength gradesThe tensile strength grades are defined in Table 1.NOTE
The nominal values are the minimum tensile strength limits. The upper limits (maximum) are equal to these minimumvalues increased with the tolerances specified in EN 10264-1 Table 1.SIST EN 10264-3:2003

Subject to agreement between the manufacturer and the purchaser, other tensile strengthgrades can be used.a 1 MPa = 1 N/mm2.b Mass of coatings for static and dynamic applications are specified in Table 10.5.2 Profiles5.2.1 Definition of shaped wireFor shaped wire, the characteristic sections of the wire are shown in Figure 1 for full lock Z, half lock H andtrapezoidal T wires.The nominal dimensions and tolerances shall be agreed between the supplier and the purchaser at the time ofordering. The conventional characteristic values are as follows:h: height: difference between the radii of the 2 concentric boundary circles.b: width: maximum width of upper part perpendicular to a radial line passing through the centre of the width (asshown in Figure 1).w: minimum narrowing: is the smallest width of the profile.e: distance taken diagonally across the transverse section of the profile (essentially trapezoidal or T profile).The designation of a full lock wire is established using the letter Z and the height (h), that of a half lock wire by Hfollowed by the height (h) and the minimum narrowing (w) (h x w) and that of a trapezoidal wire by the letter Tfollowed by the height (h).Table 2 gives the design criteria for the shaped wire shown in Figure 1. These are the relation between the heightof the shaped wires and the other major characteristic dimensions.SIST EN 10264-3:2003
...