iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13155:2020/prA1

(Amendment)

Cranes - Safety - Non-fixed load lifting attachments

Cranes - Safety - Non-fixed load lifting attachments

This document specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices:
a)   plate clamps;
b)   vacuum lifters:
1)   self-priming;
2)   non-self-priming (pump, venturi, turbine);
c)   lifting magnets:
1)   electric lifting magnets (battery fed and mains-fed);
2)   permanent lifting magnets;
3)   electro-permanent lifting magnets;
d)   lifting beams;
e)   C-hooks;
f)   lifting forks;
g)   clamps;
h)   lifting insert systems for use in normal weight concrete,
as defined in Clause 3.
This document does not give requirements for:
-   non-fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;
-   hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);
-   hazards caused by operation in an explosive atmosphere;
-   hazards caused by noise;
-   hazards relating to the lifting of persons;
-   electrical hazards;
-   hazards due to hydraulic and pneumatic components.
For high risk applications not covered by this standard, EN 13001-2:2014, 4.3.2 gives guidance to deal with them.
This document covers the proof of static strength, the elastic stability and the proof of fatigue strength.
This document does not generally applies to attachments intended to lift above people. Some attachments are suitable for that purpose if equipped with additional safety features. In such cases the additional safety features are specified in the specific requirements.
This document does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets. This document does not cover power operated container handling spreaders, which are in the scope of EN 15056.
This document is not applicable to non-fixed load attachments manufactured before the date of its publication.
1   Modification to Clause 1, "Scope"
2nd paragraph after list, replace the reference to EN 13001-2:2014 with:
"EN 13001-2:2021".

Krane - Sicherheit - Lose Lastaufnahmemittel

1   Änderung von Abschnitt 1 "Anwendungsbereich"
2. Absatz nach der Liste, Verweisung auf EN 13001-2:2014 ersetzen durch:
"EN 13001-2:2021".

Appareils de levage à charge suspendue - Sécurité - Accessoires de levage amovibles

1   Modification de l’Article 1 "Domaine d'application"
2ème alinéa après la liste, remplacer la référence à l’EN 13001-2:2014 par  :
"EN 13001-2:2021".

Dvigala (žerjavi) - Varnost - Snemljiva dvigalna sredstva - Dopolnilo A1

General Information

Status
Not Published
Publication Date
09-Oct-2024
ICS
53.020.30 - Accessories for lifting equipment
Technical Committee
CEN/TC 147 - Cranes - Safety
Drafting Committee
CEN/TC 147/WG 21 - Non-fixed load lifting attachments
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
25-Apr-2024
Due Date
14-Mar-2023
Completion Date
25-Apr-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 13155:2021/oprA1:2023 - Cranes - Safety - Non-fixed load lifting attachments

Relations

Amends
EN 13155:2020 - Crane - Safety - Non-fixed load lifting attachments
Effective Date
09-Jun-2021

Buy Standard

EN 13155:2021/oprA1:2023EN 13155:2021/oprA1:2023
PreviousNext
Draft
EN 13155:2021/oprA1:2023
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13155:2021/oprA1:2023
01-maj-2023
Dvigala (žerjavi) - Varnost - Snemljiva dvigalna sredstva - Dopolnilo A1
Cranes - Safety - Non-fixed load lifting attachments
Krane - Sicherheit - Lose Lastaufnahmemittel
Appareils de levage à charge suspendue - Sécurité - Accessoires de levage amovibles
Ta slovenski standard je istoveten z: EN 13155:2020/prA1
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
SIST EN 13155:2021/oprA1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13155:2021/oprA1:2023

---------------------- Page: 2 ----------------------
SIST EN 13155:2021/oprA1:2023


DRAFT
EUROPEAN STANDARD
EN 13155:2020
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
March 2023
ICS 53.020.30
English Version

Cranes - Safety - Non-fixed load lifting attachments
Appareils de levage à charge suspendue - Sécurité - Krane - Sicherheit - Lose Lastaufnahmemittel
Accessoires de levage amovibles
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 147.

This draft amendment A1, if approved, will modify the European Standard EN 13155:2020. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13155:2020/prA1:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13155:2021/oprA1:2023
EN 13155:2020/prA1:2023 (E)
Contents Page
European foreword . 3
1 Modification to Clause 1, "Scope" . 4
2 Modifications to Clause 2, "Normative references" . 4
3 Modifications to Clause 3, "Terms and definitions" . 4
4 Modifications to Clause 4 "List of significant hazards" . 4
5 Modifications to Clause 5, "Safety requirements and/or protective measures" . 5
6 Modifications to Clause 6, "Verification of the safety requirements and/or protective
measures" . 7
7 Modifications to Clause 7, "Information for use" . 10
8 Modifications to Annex A "General verification methods" . 11
9 Modifications to Annex C "Verification methods of vacuum lifters" . 12
10 Modifications to Annex E "Verification methods for lifting beams" . 12
11 Modifications to Annex H "Verification methods for lifting insert systems" . 12

2

---------------------- Page: 4 ----------------------
SIST EN 13155:2021/oprA1:2023
EN 13155:2020/prA1:2023 (E)
European foreword
This document (EN 13155:2020/prA1:2023) has been prepared by Technical Committee CEN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13001-3-5:2016+A1:2021(Main + Amendment)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13155:2020(Main)
Crane - Safety - Non-fixed load lifting attachments
SIST EN 13155:2021

This document specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices:
a)   plate clamps;
b)   vacuum lifters:
1)   self-priming;
2)   non-self-priming (pump, venturi, turbine);
c)   lifting magnets:
1)   electric lifting magnets (battery fed and mains-fed);
2)   permanent lifting magnets;
3)   electro-permanent lifting magnets;
d)   lifting beams;
e)   C-hooks;
f)   lifting forks;
g)   clamps;
h)   lifting insert systems for use in normal weight concrete,
as defined in Clause 3.
This document does not give requirements for:
-   non-fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;
-   hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);
-   hazards caused by operation in an explosive atmosphere;
-   hazards caused by noise;
-   hazards relating to the lifting of persons;
-   electrical hazards;
-   hazards due to hydraulic and pneumatic components.
For high risk applications not covered by this standard, EN 13001-2:2014, 4.3.2 gives guidance to deal with them.
This document covers the proof of static strength, the elastic stability and the proof of fatigue strength.
This document does not generally applies to attachments intended to lift above people. Some attachments are suitable for that purpose if equipped with additional safety features. In such cases the additional safety features are specified in the specific requirements.
This document does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets. This document does not cover power operated container handling spreaders, which are in the scope of EN 15056.
This document is not applicable to non-fixed load attachments manufactured before the date of its publication.

  • Standard
    112 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14502-1:2010(Main)
Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets
SIST EN 14502-1:2010

This European Standard applies to baskets suspended on cranes.
This European Standard does not cover the controls for the movement of the basket.
This European Standard is not applicable to:
-   lifts for crane drivers;
-   moveable cabins.
This European Standard deals with all significant hazards, hazardous situations and events relevant to suspended baskets, when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
The significant hazards covered by this document are identified in Clause 4.
This European Standard is not applicable to suspended baskets which are manufactured before the date of publication by CEN.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-5:2016/FprA1(Amendment)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016/kFprA1:2019

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13155 rev(Main)
Crane - Safety - Non-fixed load lifting attachments
oSIST prEN 13155:2011

To revise the standard to include non-fixed lifting attachments used during drilling operations.

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13155 rev(Main)
Crane - Safety - Non-fixed load lifting attachments
oSIST prEN 13155:2014

To revise the standard to include non-fixed lifting attachments used during drilling operations.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-3:2022(Main)
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
SIST EN 13411-3:2023

This document deals with the requirements for the ferrule-securing of eyes and endless loops.
It also deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops.
This document applies to the ferrule-securing of eye terminations formed either by a Flemish eye or turn-back eye and covers ferrules made of non-alloy carbon steel and aluminium.
This document applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60 mm diameter conforming to EN 12385-4, lift ropes conforming to EN 12385-5 and spiral strand ropes conforming to EN 12385-10.
Type testing of ferrule-secured systems and manufacturing quality control requirements are also specified.
This document deals with all significant hazards, hazardous situations, and events relevant to this particular steel wire rope termination when used as intended and under conditions of use which are foreseeable by the manufacturer.
This document applies to terminations of steel wire ropes with ferrules and ferrule-securing which are manufactured after the date of this publication.
NOTE   One design of ferrule-secured turn-back eye termination using an oval aluminium ferule which satisfies the requirements of this document when securing ropes having rope grades up to and including 1960 is given for information in Annex A.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-7:2021(Main)
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
SIST EN 13411-7:2021

This document specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This document covers those symmetric wedge sockets intended for use at temperatures between −20 °C and 100 °C.
This document only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A.
This document deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The hazards covered by this document are identified in Clause 4.
This document applies to symmetric wedge sockets, which are manufactured after the date of its publication.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-5:2016+A1:2021(Main + Amendment)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-9:2021(Main)
Terminations for steel wire ropes - Safety - Part 9: Solid thimbles
SIST EN 13411-9:2021

This document specifies the minimum requirements for solid thimbles made of steel or cast iron for terminations of stranded steel wire ropes.
This document is applicable to ferrule-secured terminations with solid thimbles in combination with ferrules (see EN 13411-3), that have an efficiency factor KT of at least 0,9, and to spliced terminations with solid thimbles (see EN 13411-2), that have an efficiency factor KT of at least 0,8, which are used as accessories for steel wire ropes, such as slings or wire rope assemblies, having a lifting, lowering or load-bearing effect in hoisting equipment.
Examples of designs of solid thimbles which meet the requirements of this standard are given in informative Annexes B and C.
Round thimbles (thimble with rotational symmetry around the bore) are not subject to this document.
This document is applicable to ferrule-secured terminations that are manufactured after the date of publication of this document.
Hazards that are dealt with in this document are listed in Clause 4.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day