EN 15553:2021+A1:2024
(Main)Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method
Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method
This document specifies a fluorescent indicator adsorption method for the determination of hydrocarbon types over the concentration ranges from 5 % (V/V) to 99 % (V/V) aromatic hydrocarbons, 0,3 % (V/V) to 55 % (V/V) olefins, and 1 % (V/V) to 95 % (V/V) saturated hydrocarbons in petroleum fractions that distil below 315 °C. This method can apply to concentrations outside these ranges, but the precision has not been determined.
When samples containing oxygenated blending components are analysed, the hydrocarbon type results can be reported on an oxygenate-free basis or, when the oxygenate content is known, the results can be corrected to a total-sample basis.
This test method is applicable to full boiling range products. Cooperative data have established that the precision statement does not apply to petroleum fractions with narrow boiling ranges near the 315 °C limit. Such samples are not eluted properly, and results are erratic.
It does not apply to samples containing dark-coloured components that interfere with reading the chromatographic bands that cannot be analysed.
NOTE 1 The oxygenated blending components methanol, ethanol, tert-butyl methyl ether (MTBE), methyl tert-pentyl ether (TAME) and tert-butyl ethyl ether (ETBE) do not interfere with the determination of hydrocarbon types at concentrations normally found in commercial petroleum blends. These oxygenated compounds are not detected since they elute with the alcohol desorbent. The effects of other oxygenated compounds are individually verified.
NOTE 2 For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Kohlenwasserstofftypen - Adsorptionsverfahren mit Fluoreszenz-Indikator
Dieses Dokument legt ein Adsorptionsverfahren mit Fluoreszenz-Indikator fest für die Bestimmung der nachfolgend genannten Kohlenwasserstofftypen in Mineralölfraktionen, die unterhalb von 315 °C sieden, und zwar für aromatische Kohlenwasserstoffe im Konzentrationsbereich von 5 % (V/V) bis 99 % (V/V), für olefinische Kohlenwasserstoffe im Konzentrationsbereich von 0,3 % (V/V) bis 55 % (V/V) und für gesättigte Kohlenwasserstoffe im Konzentrationsbereich von 1 % (V/V) bis 95 % (V/V). Dieses Prüfverfahren kann auch auf Konzentrationen außerhalb der angegebenen Bereiche angewendet werden, jedoch ist dafür keine Präzision bestimmt worden.
Wenn Proben, die sauerstoffhaltige Blendkomponenten enthalten, analysiert werden, können die Kohlenwasserstofftypen auf „sauerstofffreier“ Basis angegeben werden, oder, wenn der Gehalt an sauerstoffhaltigen Verbindungen bekannt ist, auch nach entsprechend korrigierter Umrechnung mit Bezug auf die Gesamtprobe.
Dieses Prüfverfahren ist auf Produkte im gesamten angegebenen Siedebereich anwendbar. Untersuchungen haben gezeigt, dass die Präzisionsangaben nicht gelten für engsiedende Mineralölfraktionen nahe der angegebenen Grenze von 315 °C. Solche Proben werden nicht ordnungsgemäß eluiert und führen daher zu fehlerhaften Ergebnissen.
Es ist nicht anwendbar für Proben, die dunkel gefärbte Komponenten enthalten, welche die Auswertung der chromatographischen Zonen stören, und nicht untersucht werden können.
ANMERKUNG 1 Die sauerstoffhaltigen Blendkomponenten Methanol, Ethanol, tert-Butylmethylether (MTBE), Methyl-tert-pentylether (TAME, tert-Amylmethylether) und tert-Butylethylether (ETBE) stören mit für kommerzielle Mineralölmischungen üblichen Gehalten die Bestimmung nicht. Diese sauerstoffhaltigen Verbindungen werden nicht erfasst, weil sie zusammen mit dem alkoholischen Desorptionsmittel eluieren. Die Einflüsse anderer sauerstoffhaltiger Verbindungen werden im Einzelfall geprüft.
ANMERKUNG 2 Für die Zwecke dieses Dokuments wird zur Angabe des Massenanteils einer Substanz der Ausdruck „% (m/m)“ und für den Volumenanteil einer Substanz der Ausdruck „% (V/V)“ verwendet.
WARNUNG — Die Anwendung dieses Dokuments kann die Anwendung gefährlicher Stoffe, Arbeitsgänge und Geräte mit sich bringen. Dieses Dokument beansprucht nicht, alle damit verbundenen Sicherheitsprobleme zu behandeln. Es liegt in der Verantwortung des Anwenders dieses Dokuments geeignete Maßnahmen für die Sicherheit und den Gesundheitsschutz zu ergreifen, und die Geltung weiterer diesbezüglicher Auflagen zu prüfen.
Produits pétroliers et produits connexes - Détermination des groupes d'hydrocarbures - Méthode par adsorption en présence d'indicateur fluorescent
Le présent document spécifie une méthode d’adsorption en présence d’indicateur fluorescent visant à déterminer les groupes d’hydrocarbures sur des plages de concentration comprises entre 5 % (V/V) et 99 % (V/V) pour les hydrocarbures aromatiques, entre 0,3 % (V/V) et 55 % (V/V) pour les oléfines, et entre 1 % (V/V) et 95 % (V/V) pour les hydrocarbures saturés dans des fractions pétrolières distillant en dessous de 315 °C. La présente méthode peut être applicable à des concentrations en dehors de ces plages, mais la fidélité n’a pas été déterminée.
Lorsque des échantillons contenant des composés oxygénés sont analysés, les résultats de groupes d’hydrocarbures peuvent être notés sans tenir compte des composés oxygénés ou, lorsque la teneur en oxygénés est connue, les résultats peuvent être corrigés sur la base de l’échantillon total.
La présente méthode d’essai est applicable aux produits à plage d’ébullition large. Des données communes ont établi que la déclaration de fidélité ne s’applique pas aux fractions de pétrole à plage d’ébullition étroite avoisinant le seuil de 315 °C. Ces échantillons ne sont pas correctement élués, ce qui conduit à des résultats erronés.
Cette méthode ne s’applique pas aux échantillons qui contiennent des composants de couleur foncée pouvant affecter la lecture des bandes chromatographiques.
NOTE 1 Les composés oxygénés comme le méthanol, l’éthanol, le méthyl tertio-butyl éther (MTBE), le méthyl tertio-pentyl éther (TAME) et l’éthyl-tertio-butyl éther (ETBE) n’affectent pas la détermination des groupes d’hydrocarbures aux concentrations habituellement trouvées dans les mélanges commerciaux de produits pétroliers disponibles. Ces composés oxygénés ne sont pas détectés puisqu’ils éluent avec l’alcool de désorption. Les effets des autres composés oxygénés sont vérifiés individuellement.
NOTE 2 Pour les besoins du présent document, les termes “% (m/m)” et “% (V/V)” sont utilisés pour représenter respectivement la fraction massique et la fraction volumique.
AVERTISSEMENT — L’utilisation du présent document peut impliquer des produits, opérations et équipements à caractère dangereux. Le présent document n’a pas la prétention d’aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l’utilisateur de ce document d’établir des règles de sécurité et d’hygiène appropriées et de déterminer l’applicabilité des restrictions réglementaires avant son utilisation.
Naftni proizvodi in sorodni materiali - Določanje vrste ogljikovodikov - Adsorpcijska metoda s fluorescenčnim indikatorjem
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2025
Naftni proizvodi in sorodni materiali - Določanje vrste ogljikovodikov -
Adsorpcijska metoda s fluorescenčnim indikatorjem
Petroleum products and related materials - Determination of hydrocarbon types -
Fluorescent indicator adsorption method
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der
Kohlenwasserstofftypen - Adsorptionsverfahren mit Fluoreszenz-Indikator
Produits pétroliers et produits connexes - Détermination des groupes d'hydrocarbures -
Méthode par adsorption en présence d'indicateur fluorescent
Ta slovenski standard je istoveten z: EN 15553:2021+A1:2024
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 15553:2021+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2024
EUROPÄISCHE NORM
ICS 75.080 Supersedes EN 15553:2021
English Version
Petroleum products and related materials - Determination
of hydrocarbon types - Fluorescent indicator adsorption
method
Produits pétroliers et produits connexes - Mineralölerzeugnisse und verwandte Produkte -
Détermination des groupes d'hydrocarbures - Méthode Bestimmung der Kohlenwasserstofftypen -
par adsorption en présence d'indicateur fluorescent Adsorptionsverfahren mit Fluoreszenz-Indikator
This European Standard was approved by CEN on 28 October 2021 and includes Amendment 1 approved by CEN on 7 October
2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15553:2021+A1:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Principle . 5
5 Reagents and materials . 5
6 Apparatus . 6
7 Sampling and sample handling . 9
8 Apparatus preparation . 9
9 Procedure. 9
10 Calculation . 12
11 Expression of results . 12
12 Precision . 13
12.1 General . 13
12.2 Repeatability, r . 13
12.3 Reproducibility, R . 13
13 Test report . 16
Annex A (normative) Specification for silica gel . 17
Annex B (informative) Standard adsorption column . 18
B.1 General . 18
B.2 Analyser section checking . 19
B.3 Column assembly . 19
Bibliography . 20
European foreword
This document (EN 15553:2021+A1:2024) has been prepared by Technical Committee CEN/TC 19
“Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and biological origin”,
the secretariat of which is held by NEN.
This document shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by June 2025, and conflicting national standards shall be withdrawn at
the latest by June 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 7 October 2024.
This document supersedes !EN 15553:2021".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
This document [EN 15553:2021] supersedes EN 15553:2007. It is originally based on IP 156/06 [1]. It
is intended as an alternative method to ASTM D1319 [2], which requires a de-pentanization step.
In comparison with the previous edition [EN 15553:2007], the following technical modification has
been made:
— lot numbers of the to be used reformulated dyed gel (5.2) that are questionable in their use have
been excluded and clarification of correct references to the gel have been included.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
1 Scope
This document specifies a fluorescent indicator adsorption method for the determination of
hydrocarbon types over the concentration ranges from 5 % (V/V) to 99 % (V/V) aromatic
hydrocarbons, 0,3 % (V/V) to 55 % (V/V) olefins, and 1 % (V/V) to 95 % (V/V) saturated hydrocarbons
in petroleum fractions that distil below 315 °C. This method can apply to concentrations outside these
ranges, but the precision has not been determined.
When samples containing oxygenated blending components are analysed, the hydrocarbon type results
can be reported on an oxygenate-free basis or, when the oxygenate content is known, the results can be
corrected to a total-sample basis.
This test method is applicable to full boiling range products. Cooperative data have established that the
precision statement does not apply to petroleum fractions with narrow boiling ranges near the 315 °C
limit. Such samples are not eluted properly, and results are erratic.
It does not apply to samples containing dark-coloured components that interfere with reading the
chromatographic bands that cannot be analysed.
NOTE 1 The oxygenated blending components methanol, ethanol, tert-butyl methyl ether (MTBE), methyl tert-
pentyl ether (TAME) and tert-butyl ethyl ether (ETBE) do not interfere with the determination of hydrocarbon
types at concentrations normally found in commercial petroleum blends. These oxygenated compounds are not
detected since they elute with the alcohol desorbent. The effects of other oxygenated compounds are individually
verified.
NOTE 2 For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent
respectively the mass fraction and the volume fraction.
WARNING — The use of this document can involve hazardous materials, operations and equipment.
This document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and
determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1601, Liquid petroleum products — Determination of organic oxygenate compounds and total
organically bound oxygen content in unleaded petrol — Method by gas chromatography (O-FID)
EN 13132, Liquid petroleum products — Unleaded petrol — Determination of organic oxygenate
compounds and total organically bound oxygen content by gas chromatography using column switching
EN ISO 3170, Petroleum liquids — Manual sampling (ISO 3170)
EN ISO 3171, Petroleum liquids — Automatic pipeline sampling (ISO 3171)
EN ISO 3696, Water for analytical laboratory use — Specification and test methods (ISO 3696)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
saturates
volume percentage of alkanes plus cycloalkanes
3.2
olefins
volume percentage of alkenes plus cycloalkenes plus some alkadienes
3.3
aromatics
volume percentage of monocyclic and polycyclic aromatic hydrocarbons plus aromatic olefinic
hydrocarbons, some dienes, compounds containing sulfur and nitrogen, or higher-boiling oxygenated
compounds
4 Principle
Approximately 0,75 ml of sample is introduced into a special glass adsorption column packed with
activated silica gel. A small layer of the silica gel contains a mixture of fluorescent dyes. When all the
sample has been adsorbed onto the gel, alcohol is added to desorb the sample down the column. The
hydrocarbons are separated, according to their adsorption affinities, into aromatics, olefins and
saturates. The fluorescent dyes are also separated selectively with the hydrocarbon types, and render
the boundaries of the aromatic, olefin and saturate zones visible under ultraviolet light. The volume
percentage of each hydrocarbon type is calculated from the length of each zone in the column.
NOTE See NOTE 1 under Clause 1 for hydrocarbons that the described method cannot measure.
5 Reagents and materials
Use only chemicals and reagents of recognized analytical grade and water conforming to grade 3 of
EN ISO 3696.
5.1 Silica gel, manufactured to conform to the specifications given in Annex A.
NOTE 1 Grace Davison silica gel Grade 923 meets the requirements of this specification. This information is
given for the convenience of users of this document and does not constitute an endorsement by CEN of this
product.
Before use, dry the gel in a shallow vessel at 175 °C for at least 3 h. Transfer the dried gel to an airtight
container while still hot, and protect it from atmospheric moisture.
NOTE 2 Some batches of silica gel that otherwise meet specifications have been found to produce olefin-
boundary fading. The exact reason for this phenomenon is unknown but will affect accuracy and precision.
5.2 Fluoresce
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.