EN 13165:2012+A2:2016
(Main)Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification
This European Standard specifies the requirements for factory made rigid polyurethane foam (PU) products, with or without facings or coatings, which are used for the thermal insulation of buildings. PU includes both PIR and PUR products. The products are manufactured in the form of boards.
This European Standard includes PU multi-layered insulation products, see Annex D.
Products covered by this standard are also used in prefabricated thermal insulation systems and composite insulation products; the performance of systems incorporating these products is not covered.
This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.
Products with a declared thermal resistance lower than 0,25 m2⋅K/W or a declared thermal conductivity greater than 0,060 W/(m⋅K) at 10 °C are not covered by this European Standard.
This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations (covered by EN 14308).
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PU) - Spezifikation
Diese Europäische Norm legt die Anforderungen an werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PU) mit oder ohne Kaschierung oder Beschichtung fest, die für die Wärmedämmung von Gebäuden benutzt werden. PU umfasst sowohl PIR- als auch PUR-Produkte. Die Produkte werden in Form von Platten hergestellt.
!Diese Europäische Norm umfasst mehrlagige PU-Dämmprodukte, siehe Anhang D."
Die in dieser Norm beschriebenen Produkte werden auch in vorgefertigten Wärmedämmsystemen und !Mehrschicht-Dämmprodukte" verwendet. Die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Die vorliegende Norm beschreibt die Produkteigenschaften und enthält die Prüfverfahren und Festlegungen für die Konformitätsbewertung, die Kennzeichnung und die Etikettierung.
Diese Norm legt keine Leistungsstufen für eine vorgegebene Eigenschaft fest, die ein Produkt erreichen muss, um für einen bestimmten Anwendungsfall tauglich zu sein. Die für bestimmte Anwendungen benötigten Stufen können Regelwerken oder nicht entgegenstehenden Normen entnommen werden.
Diese Europäische Norm gilt nicht für Produkte, deren Nennwert des Wärmedurchlasswiderstandes niedriger als 0,25 m2⋅K/W oder deren Nennwert der Wärmeleitfähigkeit größer als 0,060 W/(m⋅K) bei 10 °C ist.
Die vorliegende Norm gilt weder für in situ Dämmprodukte noch für Produkte, die zur Dämmung von haus-technischen und betriebstechnischen Anlagen (durch EN 14308 abgedeckt) vorgesehen sind.
Produits isolants thermiques pour le bâtiment - Produits manufacturés en mousse rigide de polyuréthane (PU) - Spécification
La présente Norme européenne spécifie les exigences auxquelles doivent satisfaire les produits manufacturés en mousse rigide de polyuréthanne (PU), avec ou sans parements ou enduits de finition, utilisés pour l'isolation thermique des bâtiments. Le PU comprend les produits PIR et PUR. Les produits sont fabriqués sous forme de panneaux.
!La présente Norme européenne inclut les produits isolants PU multicouches, voir l'Annexe D."
Les produits couverts par la présente norme sont également utilisés dans des systèmes d'isolation thermique et dans des !produits isolants composites" préfabriqués ; les performances des systèmes incorporant ces produits ne sont pas définies.
La présente norme décrit les caractéristiques des produits et contient des modes opératoires d'essai, d'évaluation de la conformité, de marquage et d'étiquetage.
La présente norme ne spécifie pas, pour une propriété donnée, le niveau exigé que doit atteindre un produit pour démontrer son aptitude à l'emploi dans une application particulière. Les niveaux requis pour une application donnée figurent dans les réglementations ou normes non conflictuelles.
Les produits dont la résistance thermique déclarée à une température de 10 °C est inférieure à 0,25 m2·K/W ou dont la conductivité thermique déclarée à une température de 10 °C est supérieure à 0,060 W/(m·K) ne relèvent pas du domaine d'application de la présente Norme européenne.
Les produits isolants mis en œuvre in situ et les produits destinés à être utilisés pour l'isolation des équipements du bâtiment et des installations industrielles ne relèvent pas du domaine d'application de la présente norme (couverts par l’EN 14308).
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz trde poliuretanske pene (PUR) - Specifikacija
Ta evropski standard določa zahteve za površinsko obdelane ali lakirane ali površinsko neobdelane ali nelakirane proizvode iz trde poliuretanske pene (PU), ki se uporabljajo za toplotno izolacijo stavb. PU zajema proizvode PIR in PUR. Proizvodi so izdelani v obliki plošč.
Ta evropski standard zajema večplastne izolacijske proizvode iz poliuretanske pene (glej dodatek D).
Proizvodi iz tega standarda se uporabljajo tudi v montažnih sistemih toplotne izolacije in kompozitnih izolacijskih proizvodih; lastnosti sistemov iz teh proizvodov niso opisane.
Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje.
Ta standard ne določa zahtevane ravni določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevane ravni za posamezno uporabo so določene v uredbah ali standardih, ki niso v nasprotju s tem standardom.
Proizvodi z deklarirano toplotno upornostjo, nižjo od 0,25 m2 K/W, ali deklarirano toplotno prevodnostjo, višjo od 0,060 W/(m K) pri 10 °C, v tem evropskem standardu niso zajeti.
Ta standard ne zajema toplotnoizolacijskih proizvodov, izdelanih na kraju samem, ter proizvodov za izolacijo gradbene opreme in industrijskih napeljav (zajema jih standard EN 14308).
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz trde poliuretanske pene (PUR) - SpecifikacijaWärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PU) - SpezifikationProduits isolants thermiques pour le bâtiment - Produits manufacturés en mousse rigide de polyuréthane (PU) - SpécificationThermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 13165:2012+A2:2016SIST EN 13165:2013+A2:2016en,fr,de01-september-2016SIST EN 13165:2013+A2:2016SLOVENSKI
STANDARDSIST EN 13165:2013+A1:20151DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13165:2012+A2
June 2016 ICS 91.100.60 Supersedes EN 13165:2012+A1:2015
English Version
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification
Produits isolants thermiques pour le bâtiment - Produits manufacturés en mousse rigide de polyuréthane (PU) - Spécification
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Polyurethan-Hartschaum (PU) - Spezifikation This European Standard was approved by CEN on 6 October 2012 and includes Amendment 1 approved by CEN on 15 December 2014 and Amendment 2 approved by CEN on 23 February 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13165:2012+A2:2016 E SIST EN 13165:2013+A2:2016
Determination of the declared values of thermal resistance and thermal conductivity . 24 A.1 General . 24 A.2 Input data. 24 A.3 Declared values . 24 Annex B (normative)
!Product type determination" (!PTD") and factory production control (FPC) . 26 Annex C (normative)
Determination of the aged values of thermal resistance and
thermal conductivity . 30 C.1 General . 30 C.2 Sampling and test specimen preparation . 30 C.3 Determination of the initial value of thermal conductivity . 31 C.4 Determination of the accelerated aged value of thermal conductivity . 32 C.5 Fixed increment procedure . 35 C.6 Declaration of the aged values of thermal resistance and thermal conductivity . 37 Annex D (normative)
PU multi-layered insulation products . 39 D.1 General . 39 D.2 Requirements . 39 D.3 Test methods . 40 D.4 Evaluation of conformity . 40 Annex E (informative)
Additional properties . 41 E.1 General . 41 E.2 Bending strength . 41 E.3 Shear behaviour . 41 E.4 Compressive stress at 2% deformation . 41 E.5 Long term water absorption by diffusion . 41 E.6 Freeze-thaw resistance . 41 E.7 Apparent density . 42 Annex ZA (informative)
!Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation" . 43 Bibliography . 54 SIST EN 13165:2013+A2:2016
Tables Table 1 — Tolerances on length and width . 13 Table 2 — Classes for thickness tolerances . 13 Table 3 — Deviation from flatness . 13 Table 4 — Test conditions for dimensional stability under specified temperature and humidity conditions . 14 Table 5 — Levels for dimensional stability for test conditions 1, 2, 3 . 15 Table 6 — Levels for dimensional stability for test condition 4 . 15 Table 7 — Levels for deformation under specified compressive load and temperature conditions . 15 Table 8 — Levels for compressive stress or compressive strength . 16 Table 9 — Levels for tensile strength perpendicular to faces . 16 Table 10 — Levels for one sided wetting behaviour . 17 Table 11 — Test methods, test specimens and conditions . 20 Table A.1 — Values for k for one sided 90 % tolerance interval with a confidence level of 90 % . 25 Table B.1 — Minimum number of tests for !PTD" and minimum product testing frequencies . 26 Table B.2 — Minimum product testing frequencies for the reaction to fire characteristics . 28 Table C.1 — #Safety increments to be added to the measured accelerated aged value of thermal conductivity$ . 33 Table C.2 — #Increments for calculating the aged value of thermal conductivity$. 37 Table E.1 — Test methods, test specimens, conditions and minimum testing frequencies . 42 Table ZA.1 — Relevant clauses for factory made rigid polyurethane foam and intended use . 44 Table ZA.2 — Systems of AVCP . 45 Table ZA.3.1 — Assignment of AVCP tasks for factory made rigid polyurethane foam products under system 1 for reaction to fire and system 3 (see Table ZA.2) . 46 Table ZA.3.2 — Assignment of AVCP tasks for factory made rigid polyurethane foam products under system 3 (see Table ZA.2) . 47 Table ZA.3.3 — Assignment of AVCP tasks for factory made rigid polyurethane foam products under combined system 4 for reaction to fire and system 3 (see Table ZA.2). 47
Figures Figure C.1 — Flow chart of the alternative ageing procedures . 31 Figure C.2 — Illustration of the acceleration test . 34 Figure ZA.1 — !Example CE marking information of products under AVCP system 1 and system 3" . 53
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.