EN ISO 11148-2:2011

Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools (ISO/FDIS 11148-2:2011)

ISO 11148-2:2011 specifies safety requirements for hand-held non-electric power tools without rotation (hereinafter "cutting-off and crimping power tools") intended for cutting off wires, cables, etc., and for crimping, for instance connectors to cable ends. The cutting-off and crimping power tools can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended to be used by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer.
ISO 11148-2:2011 is applicable to crimping tools without a yoke, cutters, cutting-off tools, cutting pliers and crimping pliers.
ISO 11148-2:2011 is not applicable to special requirements and modifications of cutting-off and crimping power tools for the purpose of mounting them in fixtures, and it is not applicable to "double acting hydraulic rescue tools for fire and rescue service use".
ISO 11148-2:2011 deals with all significant hazards, hazardous situations or hazardous events relevant to cutting-off and crimping power tools when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of cutting-off and crimping power tools in potentially explosive atmospheres.

Handgehaltene nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 2: Maschinen zum Abschneiden und Quetschen (ISO/FDIS 11148-2:2011)

Dieser Teil der ISO 11148 gilt für handgehaltene nicht elektrisch betriebene Maschinen ohne Rotationsbewegung
(im nachstehenden Text als 'Maschinen zum Abschneiden und Quetschen' bezeichnet), zum
Abschneiden von Drähten, Leitungen usw. und zum Crimpen, beispielsweise von Steckverbindern an
Leitungsenden. Die Maschinen zum Abschneiden und Quetschen können durch Druckluft, über Hydraulikflüssigkeit
oder Verbrennungsmotoren betrieben werden und sind dazu bestimmt, durch eine Bedienungsperson
verwendet und von dieser ohne oder mit einer Halterung, z. B. einer Ausgleichseinrichtung, mit einer
oder beiden Händen gehalten zu werden.
ANMERKUNG 1 Zum Zeitpunkt der Veröffentlichung dieser Norm sind keine Maschinen zum Abschneiden oder Quetschen
bekannt, die durch Verbrennungsmotoren angetrieben werden. Sobald derartige Maschinen vorliegen, wird diese
Norm entsprechend geändert.
Zu den Maschinen, die in diesem Teil der ISO 11148 behandelt werden, gehören:
 Crimpzangen ohne Gegenlager;
 Schneidmaschinen;
 Seitenschneider;
 Bündigschneider;
 Crimpzangen.
ANMERKUNG 2 Anhang B enthält Beispiele für Maschinen zum Abschneiden und Quetschen.
In diesem Teil der ISO 11148 werden folgende Punkte nicht behandelt:
besondere Anforderungen an und Änderungen bezüglich Maschinen zum Abschneiden und Quetschen
zum Zwecke des Spannens in einer Halterung;
Doppelt wirkende hydraulische Rettungsgeräte für die Feuerwehr und Rettungsdienste.
In diesem Dokument werden alle signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse
mit Ausnahme des Einsatzes von Maschinen zum Abschneiden und Quetschen in explosionsfähigen
Atmosphären behandelt, wenn sie für den dafür vorgesehenen Verwendungszweck und unter für den
Hersteller vorhersehbaren Missbrauchsbedingungen angewendet werden.
ANMERKUNG 3 EN 13463-1 enthält Anforderungen an nicht elektrisch betriebene Geräte für den Einsatz in explosionsfähigen
Atmosphären.

Machines portatives à moteur non électrique - Exigences de sécurité - Partie 2: Machines de découpe et de sertissage (ISO/FDIS 11148-2:2011)

L'ISO 11148-2:2011 spécifie des exigences de sécurité pour les machines portatives non électriques (ci-après appelées «machines de découpe et de sertissage») destinées au découpage de fils, de câbles, etc. et au sertissage, par exemple sanglage de câbles. Les machines de découpe et de sertissage peuvent être alimentées par air comprimé, par un fluide hydraulique ou par un moteur à combustion interne, et sont prévues pour être utilisées par un seul opérateur et être portées par la ou les mains de l'opérateur avec ou sans suspension, par exemple à l'aide d'un équilibreur.
Elle est applicable aux machines de sertissage sans cé; aux couteaux; aux outils de coupe; aux pinces coupantes; et aux pinces à sertir.
Elle ne couvre pas les exigences spécifiques et les modifications des machines de découpe et de sertissage destinées à être montées dans un châssis, et n'est pas applicable aux matériels de désincarcération hydrauliques à double effet à usage des services d'incendie et de secours.
Elle traite de tous les phénomènes dangereux, situations dangereuses ou événements dangereux significatifs qui sont pertinents pour les machines de découpe et de sertissage lorsqu'elles sont utilisées normalement et lorsqu'elles font l'objet d'un mauvais usage raisonnablement prévisible par le fabricant, à l'exception de l'usage des machines dans une atmosphère potentiellement explosible.

Neelektrična ročna orodja - Varnostne zahteve - 2. del: Orodja za odrezovanje in stiskanje (ISO 11148-2:2011)

Ta standard se uporablja za neelektrična ročna orodja, ki jih poganjajo rotacijski ali linearni motorji na stisnjen zrak, hidravlično tekočino ali motorje z notranjim izgorevanjem, namenjena za uporabo z enim upravljavcem, pri čemer jih podpira: – upravljavec z roko ali rokami, ali sistem vzmetenja, npr. izravnalnik, – ročno orodje, ki se ga lahko vpne.

General Information

• Status: Published
• Publication Date: 30-Nov-2011
• Withdrawal Date: 29-Jun-2012
• ICS: 25.140.10 - Pneumatic tools
• ICS: 25.140.99 - Other hand-held tools
• Technical Committee: CEN/TC 255 - Hand-held, non-electric power tools - Safety
• Drafting Committee: CEN/TC 255 - Hand-held, non-electric power tools - Safety
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Dec-2011
• Due Date: 23-Nov-2010
• Completion Date: 01-Dec-2011
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN ISO 11148-2:2012 - Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools (ISO 11148-2:2011)

Relations

• Replaces: EN 792-2:2000+A1:2008 - Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools
• Effective Date: 08-Jun-2022
• Revised: EN 792-2:2000 - Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2012
1DGRPHãþD
SIST EN 792-2:2000+A1:2008
1HHOHNWULþQDURþQDRURGMD9DUQRVWQH]DKWHYHGHO2URGMD]DRGUH]RYDQMHLQ
VWLVNDQMH,62
Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and
crimping power tools (ISO 11148-2:2011)
In der Hand gehaltene nichtelektrische Maschinen; Sicherheitsanforderungen; Teil 2:
Sicherheitsanforderungen in Bezug auf die Energieversorgung der Handmaschinen (ISO
11148-2:2011)
Machines portatives à moteur non électrique - Exigences de sécurité - Partie 2:
Machines de découpe et de sertissage (ISO 11148-2:2011)
Ta slovenski standard je istoveten z: EN ISO 11148-2:2011
ICS:
25.140.10 3QHYPDWLþQDRURGMD Pneumatic tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11148-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2011
ICS 25.140.10 Supersedes EN 792-2:2000+A1:2008
English Version
Hand-held non-electric power tools - Safety requirements - Part
2: Cutting-off and crimping power tools (ISO 11148-2:2011)
Machines portatives à moteur non électrique - Exigences Handgehaltene nicht elektrisch betriebene Maschinen -
de sécurité - Partie 2: Machines de découpe et de Sicherheitsanforderungen - Teil 2: Maschinen zum
sertissage (ISO 11148-2:2011) Abschneiden und Quetschen (ISO 11148-2:2011)
This European Standard was approved by CEN on 12 November 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11148-2:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .4

Foreword
This document (EN ISO 11148-2:2011) has been prepared by Technical Committee ISO/TC 118
"Compressors and pneumatic tools, machines and equipment" in collaboration with Technical Committee
CEN/TC 255 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at
the latest by June 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 792-2:2000+A1:2008.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11148-2:2011 has been approved by CEN as a EN ISO 11148-2:2011 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the clauses of this
standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive except ER 1.5.7 and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.

INTERNATIONAL ISO
STANDARD 11148-2
First edition
2011-12-01
Hand-held non-electric power tools —
Safety requirements —
Part 2:
Cutting-off and crimping power tools
Machines portatives à moteur non électrique — Exigences de
sécurité —
Partie 2: Machines de découpe et de sertissage

Reference number
ISO 11148-2:2011(E)
©
ISO 2011
ISO 11148-2:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 11148-2:2011(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 2
3  Terms and definitions . 2
3.1  General terms and definitions . 2
3.2  Terms and definitions related to cutting-off and crimping power tools . 4
4  Safety requirements and/or protective measures . 4
4.1  General . 4
4.2  Mechanical safety . 4
4.3  Thermal safety . 5
4.4  Noise reduction . 5
4.5  Vibration . 6
4.6  Materials and substances processed, used or exhausted . 6
4.7  Ergonomics . 6
4.8  Controls . 7
5  Verification . 7
5.1  General conditions for tests . 7
5.2  Noise . 8
5.3  Vibration . 8
5.4  Unintentional start . 8
5.5  Power tool construction . 8
5.6  Structure of verification of safety requirements . 9
6  Information for use . 9
6.1  Marking, signs and written warnings . 9
6.2  Instruction handbook . 10
6.3  Operating instructions . 15
6.4  Data . 15
6.5  Maintenance instructions . 16
Annex A (informative) List of significant hazards . 17
Annex B (informative) Examples of power tools covered by this part of ISO 11148 . 18
Annex C (normative) Symbols for labels and signs . 19
Bibliography . 20

ISO 11148-2:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11148-2 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools,
machines and equipment, Subcommittee SC 3, Pneumatic tools and machines.
ISO 11148 consists of the following parts, under the general title Hand-held non-electric power tools — Safety
requirements:
 Part 1: Assembly power tools for non-threaded mechanical fasteners
 Part 2: Cutting-off and crimping power tools
 Part 3: Drills and tappers
 Part 4: Non-rotary percussive power tools
 Part 5: Rotary percussive drills
 Part 6: Assembly power tools for threaded fasteners
 Part 7: Grinders
 Part 8: Sanders and polishers
 Part 9: Die grinders
 Part 10: Compression power tools
 Part 11: Nibblers and shears
 Part 12: Circular, oscillating and reciprocating saws
A part 13, dealing with fastener driving tools, is un
...