CEN/TS 1451-2:2019
(Main)Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
This document gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1 The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, the certification body is expected be accredited to EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 1451 1 this document is applicable to piping systems made of polypropylene (PP) intended to be used:
- for soil and waste discharge systems (low and high temperature) inside buildings (application area code “B”) and,
- for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code “BD”)
This is reflected in the marking of products by “B” or “BD”.
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Dieses Dokument enthält Empfehlungen für die Beurteilung der Konformität von Werkstoffen, Erzeug-nissen, Verbindungen und Bauteilkombinationen entsprechend des/der zutreffenden Teile(s) von EN 1451, die als Teil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Ein¬führung von Verfahren der Drittstellenzertifizierung vorgesehen sind.
ANMERKUNG 1 Es wird davon ausgegangen, dass das Qualitätsmanagementsystem EN ISO 9001 [1] oder mindestens ebenso strengen Anforderungen entspricht.
ANMERKUNG 2 Bei Drittstellenzertifizierung wird davon ausgegangen, dass die Zertifizierungsstelle in Abhängigkeit von der Anwendung nach EN ISO/IEC 17065 [2]oder EN ISO/IEC 17021 [3] zugelassen ist.
ANMERKUNG 3 Zur Unterstützung des Lesers enthält Anhang A einen Überblick über das Prüfsystem.
Dieses Dokument gilt in Verbindung mit EN 1451 1 für Rohrleitungssysteme aus Polypropylen (PP), die für folgende Verwendungszwecke vorgesehen sind:
— zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden (Anwendungs¬kennzeichen „B“); und
— zum Ableiten von Abwasser (niedriger und hoher Temperatur) sowohl innerhalb von Gebäuden als auch erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen „BD“).
Dies wird durch die Kennzeichnung auf dem Erzeugnis durch „B“ bzw. „BD“ angezeigt.
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Polypropylène (PP) - Partie 2: Guide pour l'évaluation de la conformité
Cevni sistemi iz polimernih materialov za (nizko- in visokotemperaturne) odvodne sisteme v zgradbah - Polipropilen (PP) - 2. del: Navodilo za ugotavljanje skladnosti
Ta dokument vsebuje navodila za ugotavljanje skladnosti materialov, izdelkov, spojev in sestavov z ustreznimi deli standarda EN 1451, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja s strani zunanjih ponudnikov.
OPOMBA 1: Pričakuje se, da je sistem vodenja kakovosti skladen s standardom EN ISO 9001 [1] oziroma da ni manj strog od ustreznih zahtev iz tega standarda.
OPOMBA 2: Če certificiranje izvaja zunanji ponudnik, je pričakovano, da je certifikacijski organ akreditiran v skladu s standardom EN ISO/IEC 17065 [2] oziroma EN ISO/IEC 17021 [3].
OPOMBA 3: V pomoč bralcem dodatek A vsebuje povzetek preskusnega režima.
Ta dokument se v povezavi s standardom EN 1451 1 uporablja za cevne sisteme iz polipropilena (PP), namenjene za:
– (nizko- in visokotemperaturne) odvodne sisteme v zgradbah (koda območja uporabe »B«); ter
– (nizko- in visokotemperaturne) odvodne sisteme v zgradbah in sisteme, vkopane v zgradbah (koda območja uporabe »BD«).
To je razvidno iz oznak »B« in »BD« na izdelkih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST-TS CEN/TS 1451-2:2012
Cevni sistemi iz polimernih materialov za (nizko- in visokotemperaturne) odvodne
sisteme v zgradbah - Polipropilen (PP) - 2. del: Navodilo za ugotavljanje skladnosti
Plastic piping systems for soil and waste discharge (low and high temperature) within the
building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of
conformity
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Polypropylen (PP) - Teil 2: Empfehlungen
für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées (à basse et à haute température) à l'intérieur de la structure des bâtiments -
Polypropylène (PP) - Partie 2: Guide pour l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 1451-2:2019
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 1451-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
December 2019
TECHNISCHE SPEZIFIKATION
ICS 23.040.20; 91.140.80 Supersedes CEN/TS 1451-2:2012
English Version
Plastic piping systems for soil and waste discharge (low
and high temperature) within the building structure -
Polypropylene (PP) - Part 2: Guidance for the assessment
of conformity
Systèmes de canalisations en plastique pour Kunststoff-Rohrleitungssysteme zum Ableiten von
l'évacuation des eaux-vannes et des eaux usées (à Abwasser (niedriger und hoher Temperatur) innerhalb
basse et à haute température) à l'intérieur de la der Gebäudestruktur - Polypropylen (PP) - Teil 2:
structure des bâtiments - Polypropylène (PP) - Partie Empfehlungen für die Beurteilung der Konformität
2: Guide pour l'évaluation de la conformité
This Technical Specification (CEN/TS) was approved by CEN on 7 October 2019 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1451-2:2019 E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 10
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 11
6.2.1 General . 11
6.2.2 Size groups . 11
6.2.3 Fitting groups . 11
6.3 Type testing . 11
6.4 Batch release tests . 14
6.5 Process verification tests . 16
6.6 Audit tests . 17
6.7 Indirect tests . 20
6.8 Test records . 20
Annex A (informative) Survey of test regime . 21
Bibliography . 22
European foreword
This document (CEN/TS 1451-2:2019) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 1451-2:2012. The main technical changes in the latest version of
CEN/TS 1451-2 are due the revision of EN 1451-1 from 1998.
EN 1451 consists of the following parts, under the general title Plastics piping systems for soil and waste
discharge (low and high temperature) within the building structure — Polypropylene (PP)
— Part 1: Specifications for pipes, fittings and the system
— Part 2: Guidance for the assessment of conformity (the present TS)
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type
testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document
details the applicable characteristics to be assessed as well as the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers, including a third-party certification, is given in Figure 2.
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including a
third-party certification
1 Scope
This document gives guidance for the assessment of conformity of materials, products, joints and
assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the
manufacturer’s quality plan as part of the quality management system and for the establishment of
third-party certification procedures.
NOTE 1 The quality management system is expected to conform to or is no less stringent than the relevant
requirements to EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, the certification body is expected be accredited to
EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 1451-1 this document is applicable to piping systems made of polypropylene
(PP) intended to be used:
— for soil and waste discharge systems (low and high temperature) inside buildings (application area
code “B”) and,
— for soil and waste discharge systems (low and high temperature) for both inside buildings and
buried in ground within the building structure (application area code “BD”)
This is reflected in the marking of products by “B” or “BD”.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1451-1:2017, Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1451-1 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
As impacted by EN 1451-1:2017/AC:2018.
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably accredited to EN ISO/IEC 17065 [2].
3.2
inspection body
impartial organisation or company, approved by the certification body as possessing the necessary
competence to verify and/or to carry out initial type testing, audit testing and inspection of the
manufacturer's factory production control in accordance with the relevant standard
Note 1 to entry: A inspection body is preferably accredited to EN ISO/IEC 17020 [4].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 1451, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably accredited to EN ISO/IEC 17025 [5].
3.4
quality management system
part of a management system regard to quality
[Source: EN ISO 9000:2015 [6], definition 3.5.4]
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which needs to
be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the manufacturer on materials, products or joints at specific intervals
to confirm that the process continues to be capable of producing products which conform to the
requirements given in the relevant standard
Note 1 to ent
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.