EN ISO 1478:1999
(Main)Tapping screws thread (ISO 1478:1999)
- BACK
- 29-Nov-1999
- 21.040.30
- CEN/TC 185
Tapping screws thread (ISO 1478:1999)
Blechschraubengewinde (ISO 1478:1999)
Die Internationale Norm legt das Gewinde und Gewindeenden für Blechschrauben mit Gewindegrößen ST1,5 bis ST9,5 fest.
Filetage de vis à tôle (ISO 1478:1999)
La présente Norme internationale spécifie les dimensions des filetages et des extrémités de filetage des vis à tôle de filetage ST1,5 à ST9,5 inclus.
Pločevinski navoj (ISO 1478:1999)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Blechschraubengewinde (ISO 1478:1999)Filetage de vis a tôle (ISO 1478:1999)Tapping screws thread (ISO 1478:1999)21.040.30Posebni navojiSpecial screw threadsICS:Ta slovenski standard je istoveten z:EN ISO 1478:1999SIST
...This May Also Interest You
ISO 11363-2:2017 specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper threads specified in ISO 11363-1 (i.e. 17E and 25E threads).
It provides examples of calculations for thread gauge dimensions on the large end diameter (Annex A) and draws attention to the limitations of the gauging system specified (Annex B).
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft24 pagesEnglish languagesale 10% offe-Library read for×1 day
ISO 11363-1:2018 specifies dimensions and tolerances for taper screw threads of nominal diameter 17,4 mm (designated as 17E) and 25,8 mm (designated as 25E) used for the connection of valves to gas cylinders.
ISO 11363-1:2018 does not cover the connection requirements for
- mechanical strength,
- gas tightness, and
- capability of repeated assembly and dismounting operations.
Gauge inspection is covered by ISO 11363‑2.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external and taper internal and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipment interconnected by threaded joints.
An appropriate thread sealant or jointing compound should be used on the thread to ensure pressure-tight joints.
NOTE 1 Threaded joints using taper external threads and parallel internal threads are detailed in EN 10226-1.
NOTE 2 The requirements for taper external threads are identical in EN 10226-1 and EN 10226-2.
NOTE 3 For pipe threads where pressure-tight joints are not made on the threads see EN ISO 228-1.
NOTE 4 EN 10226-3 gives details of recommended gauging systems for the verification of thread dimensions and thread form.
- Standard13 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Nov-2005
- 21.040.30
- 97/23/EC
- M/071
- ECISS/TC 110
This part of EN 10226 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products, the dimensions and tolerances of which are detailed in EN 10226-1 and prEN 10226-2.
The gauging system described may not be suitable, without special precautions, for gauging of threads on injection moulded plastic workpieces.
This part of EN 10226 does not cover completely all the requirements necessary for full control of thread quality and dimensions. Additional control of tools and equipment and visual inspection during production are required to ensure complete compliance with EN 10226-1 and prEN 10226-2, for example the length of useful thread on internally threaded workpieces should be checked by direct measurement.
Annex A gives a summary of the gauges included in this part of EN 10226, together with details of the thread elements controlled by each gauge and gauge identification numbers.
In the event of a dispute over compliance with the requirements of EN 10226-1 and prEN 10226-2, the gauges in this part of EN 10226 are to be considered as decisive for the thread elements which they control on the workpiece.
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2005
- 30-Aug-2005
- 21.040.30
- 97/23/EC
- M/071
- ECISS/TC 110
This part of EN 10226 specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure tight by the mating of the threads. These threads are taper external (designated by R) and parallel internal (designated by Rp) and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipments interconnected by threaded joints.
- Standard13 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-Oct-2004
- 21.040.30
- 97/23/EC
- M/071
- ECISS/TC 110
This second edition cancals and replaces the first edition (1980). Specifies the verification of cylindrical threads, the dimensions and tolerances of which are given in ISO 228-1. Since this 55o profile has different elements to be verified, it is necessary to provide for several GO and several NOT GO gouges.
- Standard15 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2003
- 30-Aug-2003
- 21.040.30
- 305/2011
- 89/106/EEC
- 97/23/EC
- M/071
- M/131
- ECISS/TC 110
This part of ISO 228 specifies the requirements for thread form, dimensions, tolerances and designation for
fastening pipe threads, thread sizes 1/16 to 6 inclusive. Both internal and external threads are parallel threads,
intended for the mechanical assembly of the component parts of fittings, cocks and valves, accessories, etc.
These threads are not suitable as jointing threads where a pressure-tight joint is made on the thread. If assemblies
with such threads must be made pressure-tight, this should be effected by compressing two tightening surfaces
outside the threads, and by interposing an appropriate seal.
NOTE 1 For pipe threads where pressure-tight joints are made on the threads, see ISO 7-1.
NOTE 2 ISO 228-2 gives details of methods for verification of fastening thread dimensions and form, and recommended
gauging systems.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft4 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies a method of measuring the tensile properties of stranded conductors, single strands, solid conductors and braids.
When required, it can be used also on insulated wires and cables after removing the insulation.
It is intended to be used together with EN 3475-100.
- Draft8 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-3:2016.
This document is intended to be used in conjunction with EN ISO 3691-3:2016. These requirements are supplementary to those stated in EN ISO 3691-3:2016.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
- acceleration, deceleration (kinetic energy);
- machinery mobility.
This document specifies supplementary requirements to EN ISO 3691-1:2015, EN ISO 3691-3:2016 and EN 16307-1:2020:
- brakes operation without guidance system;
- operator fall protection;
- information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.
- Draft9 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for×1 day
- 29-Jun-2023
- 53.060
- 2006/42/EC
- M/396
- CEN/TC 150
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.