EN ISO 80000-5:2013
(Main)Quantities and units - Part 5: Thermodynamics (ISO 80000-5:2007)
Quantities and units - Part 5: Thermodynamics (ISO 80000-5:2007)
ISO 80000-5:2007 gives names, symbols and definitions for quantities and units of thermodynamics. Where appropriate, conversion factors are also given.
Größen und Einheiten - Teil 5: Thermodynamik (ISO 80000-5:2007)
ISO 80000-5 enthält Benennungen, Formelzeichen und Definitionen für Größen und Einheiten der Thermo-dynamik. Wo benötigt, sind auch Umrechnungsfaktoren aufgeführt.
Grandeurs et unités - Partie 5: Thermodynamique (ISO 80000-5:2007)
L'ISO 80000-5:2007 donne les noms, les symboles et les définitions des grandeurs et unités de la thermodynamique. Des facteurs de conversion sont également indiqués, s'il y a lieu.
Veličine in enote - 5. del: Termodinamika (ISO 80000-5:2007)
Standard ISO 80000-5:2007 podaja imena, simbole in definicije za veličine in enote s področja termodinamike. Kjer je primerno, so navedeni tudi pretvorniki (pretvorni faktorji).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2013
1DGRPHãþD
SIST ISO 31-4+A1:2007
9HOLþLQHLQHQRWHGHO 7HUPRGLQDPLND ,62
Quantities and units - Part 5: Thermodynamics (ISO 80000-5:2007)
Größen und Einheiten - Teil 5: Thermodynamik (ISO 80000-5:2007)
Grandeurs et unités - Partie 5: Thermodynamique (ISO 80000-5:2007)
Ta slovenski standard je istoveten z: EN ISO 80000-5:2013
ICS:
01.060 9HOLþLQHLQHQRWH Quantities and units
17.200.01 Termodinamika na splošno Thermodynamics in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 80000-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2013
ICS 01.060
English Version
Quantities and units - Part 5: Thermodynamics (ISO 80000-
5:2007)
Grandeurs et unités - Partie 5: Thermodynamique (ISO Größen und Einheiten - Teil 5: Thermodynamik (ISO
80000-5:2007) 80000-5:2007)
This European Standard was approved by CEN on 14 March 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 80000-5:2013: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Foreword
The text of ISO 80000-5:2007 has been prepared by Technical Committee ISO/TC 12 “Quantities and units” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 80000-5:2013.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdrawn at
the latest by October 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 80000-5:2007 has been approved by CEN as EN ISO 80000-5:2013 without any modification.
INTERNATIONAL ISO
STANDARD 80000-5
First edition
2007-05-01
Corrected version
2011-06-01
Quantities and units —
Part 5:
Thermodynamics
Grandeurs et unités —
Partie 5: Thermodynamique
Reference number
ISO 80000-5:2007(E)
©
ISO 2007
ISO 80000-5:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed t o and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2007 – All rights reserved
ISO 80000-5:2007(E)
Contents Page
Foreword . iv
0 Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Names, symbols, and definitions . 1
Annex A (informative) Units based on the foot, pound, second, and some other related units . 20
Annex B (informative) Other non-SI units given for information, especially regarding the conversion
factors . 22
©
ISO 2007 – All rights reserved iii
ISO 80000-5:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 80000-5 was preparHd by Technical Committee ISO/TC 12, Quantities and units, in collaboration with
IEC/TC 25, Quantities and units.
This first edition cancels and replaces ISO 31-4:1992 and ISO 31-4:1992/Amd.1:1998. The major technical
changes from the previous standards are the following:
— the presentation of numerical statements has been changed;
— the normative references have been changed;
— some quantities concerning moisture have been added at the end of the list of quantities.
ISO 80000 consists of the following parts, under the general title Quantities and units:
— Part 1: General
— Part 2: Mathematical signs and symbols to be used in the natural sciences and technology
— Part 3: Space and time
— Part 4: Mechanics
— Part 5: Thermodynamics
— Part 7: Light
— Part 8: Acoustics
— Part 9: Physical chemistry and molecular physics
— Part 10: Atomic and nuclear physics
— Part 11: Characteristic numbers
— Part 12: Solid state physics
IEC 80000 consists of the following parts, under the general title Quantities and units:
— Part 6: Electromagnetism
— Part 13: Information science and technology
— Part 14: Telebiometrics related to human physiology
©
iv ISO 2007 – All rights reserved
ISO 80000-5:2007(E)
This corrected version of ISO 80000-5:2007 incorporates the following corrections.
— Foreword The titles of ISO/TC 12 and IEC/TC 25 have been updated.
— Footnotes 1) to 5) The footnotes have been deleted.
— Clause 2 The references have been updated.
— 5-2 (Definition) “T := 275,15 K” has been changed to “T := 273,15 K”.
0 0
— 5-2.a (Conversion factors and remarks) ISO 31-0:1992, 3.4 has been changed to ISO 80000-1:2009,
7.1.4.
— 5-14 (Symbol) α has been changed to a.
— 5-14 (Definition) α has been changed to a.
— 5-16.1 (Remarks) ISO 31-8:1992 has been changed to ISO 80000-9:2009.
— 5-19 (Remarks) ISO 31-8:1992 has been changed to ISO 80000-9:2009.
— 5-21.a (International Symbol) K has been changed to kg.
©
ISO 2007 – All rights reserved v
ISO 80000-5:2007(E)
Introduction
0.1 Arrangements of the tables
The tables of quantities and units in this International Standard are arranged so that the quantities are
presented on the left-hand pages and the units on the corresponding right-hand pages.
All units between two full lines on the right-hand pages belong to the quantities between the corresponding full
lines on the left-hand pages.
Where the numbering of an item has been changed in the revision of a part of ISO 31, the number in the
preceding edition is shown in parentheses on the left-hand page under the new number for the quantity; a dash
is used to indicate that the item in question did not appear in the preceding edition.
0.2 Tables of quantities
The names in English and in French of the most important quantities within the field of this International
Standard are given together with their symbols and, in most cases, their definitions. These names and symbols
are recommendations. The definitions are given for identification of the quantities in the International System of
Quantities (ISQ), listed on the left-hand pages of the table; they are not intended to be complete.
The scalar, vectorial or tensorial character of quantities is pointed out, especially when this is needed for the
definitions.
In most cases only one name and only one symbol for the quantity are given; where two or more names or two
or more symbols are given for one quantity and no special distinction is made, they are on an equal footing.
When two types of italic letters exist (for example as with ϑ and θ; ϕ and φ; a and a; g and g) only one of these
is given. This does not mean that the other is not equally acceptable. It is recommended that such variants
should not be given different meanings. A symbol within parentheses implies that it is a reserve symbol, to be
used when, in a particular context, the main symbol is in use with a different meaning.
In this English edition, the quantity names in French are printed in an italic font, and are preceded by fr. The
gender of the French name is indicated by (m) for masculine and (f) for feminine, immediately after the noun in
the French name.
0.3 Tables of units
0.3.1 General
The names of units for the corresponding quantities are given together with the international symbols and the
definitions. These unit names are language-dependent, but the symbols are international and the same in all
th
languages. For further information, see the SI Brochure (8 edition 2006) from BIPM and ISO 80000-1.
The units are arranged in the following way:
a) The coherent SI units are given first. The SI units have been adopted by the General Conference on
Weights and Measures (Conférence Générale des Poids et Mesures, CGPM). The use of coherent SI units
is recommended; decimal multiples and submultiples formed with the SI prefixes are recommended even
though not explicitly mentioned.
©
vi ISO 2007 – All rights reserved
ISO 80000-5:2007(E)
b) Some non-SI units are then given, being those accepted by the International Committee for Weights and
Measures (Comité International des Poids et Mesures, CIPM), or by the International Organization of Legal
Metrology (Organisation Internationale de Métrologie Légale, OIML), or by ISO and IEC, for use with the SI.
Such units are separated from the SI units in the item by use of a broken line between the SI units and the
other units.
c) Non-SI units currently accepted by the CIPM for use with the SI are given in small print (smaller than the text
size) in the “Conversion factors and remarks” column.
d) Non-SI units that are not recommended are given only in annexes in some parts of this International
Standard. These annexes are informative, in the first place for the conversion factors
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.