EN ISO 14344:2024

Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2024)

This document specifies tools for communication between a purchaser and a supplier of welding consumables within quality systems, such as those based upon ISO 9001.
This document, together with an applicable welding consumable standard (ISO or other), provides a method for preparing the specific details needed for welding consumable procurement which consists of:
a)       the welding consumable classification (selected from the applicable welding consumable standard);
b)       the lot classification (selected from Clause 4);
c)        the testing schedule (selected from Clause 5).
Selection of the specific welding consumable classification, lot classification, and testing schedule depends upon the requirements of the application for which the welding consumable is being procured.
This document does not apply to non-consumable electrodes or shielding gases.

Schweißzusätze - Beschaffung von Schweißzusätzen (ISO 14344:2024)

Dieses Dokument dient zur Verständigung zwischen einem Käufer und einem Lieferant von Schweißzusätzen im Zusammenhang mit Qualitätssicherungssystemen, zum Beispiel auf der Grundlage von ISO 9001.
Dieses Dokument liefert zusammen mit einer anwendbaren Schweißzusatznorm (ISO- oder andere Norm) ein Verfahren zur Vorbereitung der spezifischen Einzelheiten, die für die Beschaffung von Schweißzusatzwerkstoffen benötigt werden, bestehend aus:
a)   der Einteilung der Schweißzusätze (ausgewählt aus der zutreffenden Schweißzusatznorm);
b)   der Einteilung der Fertigungseinheit (ausgewählt nach Abschnitt 4);
c)   dem Prüfumfang (ausgewählt nach Abschnitt 5).
Die Auswahl der kennzeichnenden Schweißzusatzeinteilung, der Einteilung der Fertigungseinheit und des Prüfumfangs hängen von den Anforderungen des Anwendungsfalles ab, für den der Schweißzusatz beschafft wird.
Dieses Dokument ist nicht anwendbar für nichtabschmelzende Elektroden und Schutzgase.

Produits consommables pour le soudage - Approvisionnement en matériaux d'apport et flux (ISO 14344:2024)

Le présent document spécifie un outil de communication entre un acheteur et un fournisseur de produits consommables pour le soudage dans le cadre de systèmes qualité, tels que ceux basés sur l'ISO 9001.
Le présent document, combiné à une norme de produits consommables pour le soudage applicable (ISO ou autre), fournit une méthode permettant de mettre au point les détails spécifiques nécessaires à l'approvisionnement en produits consommables pour le soudage et comportant les aspects suivants:
a)       la classification du produit consommable pour le soudage (choisie d'après la norme de produits consommables pour le soudage applicable);
b)       la classification du lot (choisie d'après l'Article 4);
c)        le programme de contrôle (choisi d'après l'Article 5).
Le choix de la classification spécifique du produit consommable pour le soudage, de la classification du lot et du programme de contrôle dépend des exigences de l'application à laquelle le produit consommable pour le soudage est destiné.
Le présent document ne s'applique pas aux électrodes non consommables ou aux gaz de protection.

Dodajni in pomožni materiali za varjenje - Nabava dodajnih materialov in praškov (ISO 14344:2024)

General Information

• Status: Published
• Publication Date: 24-Sep-2024
• ICS: 25.160.20 - Welding consumables
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 3 - Welding consumables
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 25-Sep-2024
• Completion Date: 25-Sep-2024
• Ref Project: SIST EN ISO 14344:2024 - Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2024)

Relations

• Replaces: EN ISO 14344:2010 - Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2010)
• Effective Date: 08-Nov-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2024
Nadomešča:
SIST EN ISO 14344:2011
Dodajni in pomožni materiali za varjenje - Nabava dodajnih materialov in praškov
(ISO 14344:2024)
Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2024)
Schweißzusätze - Beschaffung von Schweißzusätzen (ISO 14344:2024)
Produits consommables pour le soudage - Approvisionnement en matériaux d'apport et
flux (ISO 14344:2024)
Ta slovenski standard je istoveten z: EN ISO 14344:2024
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14344
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2024
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 14344:2010
English Version
Welding consumables - Procurement of filler materials and
fluxes (ISO 14344:2024)
Produits consommables pour le soudage - Schweißzusätze - Beschaffung von Schweißzusätzen
Approvisionnement en matériaux d'apport et flux (ISO (ISO 14344:2024)
14344:2024)
This European Standard was approved by CEN on 17 May 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14344:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 14344:2024) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2025, and conflicting national standards shall
be withdrawn at the latest by March 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14344:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 14344:2024 has been approved by CEN as EN ISO 14344:2024 without any modification.

International
Standard
ISO 14344
Third edition
Welding consumables —
2024-09
Procurement of filler materials
and fluxes
Produits consommables pour le soudage — Approvisionnement
en matériaux d'apport et flux
Reference number
ISO 14344:2024(en) © ISO 2024
ISO 14344:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 14344:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Lot classification . 3
4.1 General .3
4.2 Solid welding consumables .4
4.2.1 Lot class S1 .4
4.2.2 Lot class S2 .4
4.2.3 Lot class S3 .4
4.2.4 Lot class S4 .4
4.2.5 Lot Class S5 . .4
4.3 Tubular cored electrodes and rods.4
4.3.1 Lot Class T1 .4
4.3.2 Lot Class T2 .5
4.3.3 Lot Class T3 .5
4.3.4 Lot Class T4 .5
4.4 Covered electrodes .5
4.4.1 Lot Class C1 .5
4.4.2 Lot Class C2 .5
4.4.3 Lot Class C3 .6
4.4.4 Lot Class C4 .6
4.4.5 Lot Class C5 .6
4.5 Fluxes for electroslag and submerged arc welding .6
4.5.1 Lot Class F1 .6
4.5.2 Lot Class F2 .6
5 Testing schedule . 6
5.1 General .6
5.2 Schedule 1 or F .7
5.3 Schedule 2 or G .7
5.4 Schedule 3 or H .7
5.5 Schedule 4 or I .7
5.6 Schedule 5 or J .8
5.7 Schedule 6 or K .8
6 Certification . 8
6.1 General .8
6.2 Certificates .9
6.2.1 Certificate of compliance .9
6.2.2 Certificate of conformance .9
6.2.3 Certified material test report (CMTR) .9
6.3 Inspection documents.
...