iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

ENV 1122:1995

(Main)

Determination of cadmium in plastics with the method of the wet decomposition

Determination of cadmium in plastics with the method of the wet decomposition

This European Standard describes a method for the determination of the total Cadmium (CD) content in plastics in the range of 10mg Cd/kg to 3.000mg Cd/kg. It is not suitable for polyfluorated plastic materials.

Bestimmung von Cadmium in Kunststoffen nach dem Naßaufschluß

Détermination du cadmium dans les plastiques d'après la méthode de décomposition par voie humide

La présente norme européenne décrit une méthode de dosage du cadmium dans les plastiques présentant une teneur totale comprise entre 10mg Cd/gk et 3 000mg Cd/kg.

Določevanje kadmija v polimernih materialih z metodo mokrega razklopa

General Information

Status
Withdrawn
Publication Date
12-Jan-1995
Withdrawal Date
20-Mar-2001
ICS
83.080.01 - Plastics in general
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
21-Mar-2001
Completion Date
21-Mar-2001
Ref Project
SIST ENV 1122:1999 - Determination of cadmium in plastics with the method of the wet decomposition

Relations

Replaced By
EN 1122:2001 - Plastics - Determination of cadmium - Wet decomposition method
Effective Date
22-Dec-2008

Buy Standard

ENV 1122:1999ENV 1122:1999
PreviousNext
Standardization document
ENV 1122:1999
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 1122:1999
01-maj-1999
'RORþHYDQMHNDGPLMDYSROLPHUQLKPDWHULDOLK]PHWRGRPRNUHJDUD]NORSD
Determination of cadmium in plastics with the method of the wet decomposition
Bestimmung von Cadmium in Kunststoffen nach dem Naßaufschluß
Détermination du cadmium dans les plastiques d'apres la méthode de décomposition par
voie humide
Ta slovenski standard je istoveten z: ENV 1122:1995
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST ENV 1122:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ENV 1122:1999

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 6186:2023(Main)
Plastics - Determination of pourability (ISO 6186:2023)
SIST EN ISO 6186:2023

This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 179-1:2023(Main)
Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
SIST EN ISO 179-1:2023

This document specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method can be used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions. It can also be used for the determination of comparative data from similar types of material.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6603-2:2023(Main)
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing (ISO 6603-2:2023)
SIST EN ISO 6603-2:2023

This document specifies a test method for the determination of puncture impact properties of rigid plastics, in the form of flat specimens, using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominal constant striker velocity, is necessary for detailed characterization of the impact behaviour.
The test method is applicable to specimens with a thickness between 1 mm to 4 mm.
The method is suitable for use with the following types of material:
—    rigid thermoplastic moulding and extrusion materials, including filled, unfilled and reinforced compounds and sheets;
—    rigid thermosetting moulding and extrusion materials, including filled and reinforced compounds, sheets and laminates;
—    fibre-reinforced thermoset and thermoplastic composites incorporating unidirectional or multi-directional reinforcements such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings, milled fibres and sheets made from pre-impregnated materials (prepregs).
The method is also applicable to specimens which are either moulded or machined from finished products, laminates and extruded or cast sheet.
The test results are comparable only if the conditions of preparation of the specimens, their dimensions and surfaces as well as the test conditions are the same. In particular, results determined on specimens of different thickness cannot be compared with one another (see Annex E). Comprehensive evaluation of the reaction to impact stress can be obtained by determinations made as a function of impact velocity and temperature for different material variables, such as crystallinity and moisture content.
The impact behaviour of finished products cannot be predicted directly from this test, but specimens may be taken from finished products (see above) for tests by this method.
Test data developed by this method is not intended to be used for design calculations. However, information on the typical behaviour of the material can be obtained by testing at different temperatures and impact velocities (see Annex D) by varying the thickness (see Annex E) and by testing specimens prepared under different conditions.
It is not the purpose of this document to give an interpretation of the mechanism occurring on every particular point of the force-deflection diagram. These interpretations are a task for scientific research.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 180:2023(Main)
Plastics - Determination of Izod impact strength (ISO 180:2023)
SIST EN ISO 180:2023

This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1675:2022(Main)
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO 1675:2022)
SIST EN ISO 1675:2023

This document specifies a method for the determination of the density of liquid resins using a pycnometer.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11357-1:2023(Main)
Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:2023)
SIST EN ISO 11357-1:2023

The ISO 11357 series specifies several differential scanning calorimetry (DSC) methods for the thermal analysis of polymers and polymer blends, such as
—    thermoplastics (polymers, moulding compounds and other moulding materials, with or without fillers, fibres or reinforcements),
—    thermosets (uncured or cured materials, with or without fillers, fibres or reinforcements), and
—    elastomers (with or without fillers, fibres or reinforcements).
The ISO 11357 series is applicable for the observation and measurement of various properties of, and phenomena associated with, the above-mentioned materials, such as
—    physical transitions (glass transition, phase transitions such as melting and crystallization, polymorphic transitions, etc.),
—    chemical reactions (polymerization, crosslinking and curing of elastomers and thermosets, etc.),
—    the stability to oxidation, and
—    the heat capacity.
This document specifies a number of general aspects of differential scanning calorimetry, such as the principle and the apparatus, sampling, calibration and general aspects of the procedure and test report common to all parts.
Details on performing specific methods are given in subsequent parts of the ISO 11357 series (see Foreword).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17910:2022(Main)
Biodegradable plastics - Status of standardization and new prospects
SIST-TP CEN/TR 17910:2023

This document summarizes the state of standardization in the field of biodegradable plastics and plastics products at CEN and ISO level. It explains the underlying scientific principles of biodegradation that provide the foundations for relevant test methods and enters into the merits of the individual tests to explain and clarify the reasons for the adoption of specific solutions and criteria.
This document primarily focusses on standards adopted by CEN covering environmental biodegradation testing and relevant specifications. It also includes information on disintegration and eco-toxicity tests. A full list of the international standards considered in this document is provided in Annex A.
In a second part, this document highlights areas where standardization in this field is currently lacking and where future developments may be anticipated and useful.

  • Technical report
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17615:2022(Main)
Plastics - Environmental Aspects - Vocabulary
SIST EN 17615:2022

This document specifies terms and definitions in the field of plastics related to environmental aspects and provides a common vocabulary for:
- bio-based plastics;
- biodegradability;
- carbon and environmental footprint;
- circular economy;
- design;
- plastics in natural environments;
- reuse and recycling;
- waste management.
This document aims to provide a comprehensive glossary which uses the applicable definitions providing when appropriate additional notes to make these definitions understandable without reference to other documents. Definitions are as far as possible adopted from existing standards but when the original intention or definition is unclear additional context or definitions are provided.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22007-2:2022(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 2: Transient plane heat source (hot disc) method (ISO 22007-2:2022)
SIST EN ISO 22007-2:2022

This document specifies a method for the determination of the thermal conductivity and thermal diffusivity, and hence the specific heat capacity per unit volume of plastics. The experimental arrangement can be designed to match different specimen sizes. Measurements can be made in gaseous and vacuum environments at a range of temperatures and pressures.
This method gives guidelines for testing homogeneous and isotropic materials, as well as anisotropic materials with a uniaxial structure. The homogeneity of the material extends throughout the specimen and no thermal barriers (except those next to the probe) are present within a range defined by the probing depth(s) (see 3.1).
The method is suitable for materials having values of thermal conductivity, λ, in the approximate range 0,010 W∙m−1∙K−1 < λ < 500 W∙m−1∙K−1, values of thermal diffusivity, α, in the range 5 × 10−8 m2∙s−1 < α < 10−4 m2∙s−1, and for temperatures, T, in the approximate range 50 K < T < 1 000 K.
NOTE 1   The specific heat capacity per unit volume, C, C = ρ ∙ cp, where ρ is the density and cp is the specific heat per unit mass and at constant pressure, can be obtained by dividing the thermal conductivity, λ, by the thermal diffusivity, α, i.e. C = λ/α, and is in the approximate range 0,005 MJ∙m−3∙K−1 < C < 5 MJ∙m−3∙K−1. It is also referred to as the volumetric heat capacity.
NOTE 2   If the intention is to determine the thermal resistance or the apparent thermal conductivity in the through-thickness direction of an inhomogeneous product (for instance a fabricated panel) or an inhomogeneous slab of a material, reference is made to ISO 8301, ISO 8302 and ISO 472.
The thermal-transport properties of liquids can also be determined, provided care is taken to minimize thermal convection.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11403-2:2022(Main)
Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)
SIST EN ISO 11403-2:2022

This document specifies test procedures for the acquisition and presentation of multipoint data on the following thermal and processing properties of plastics:
—    enthalpy/temperature curve;
—    linear-expansion/temperature curve;
—    melt shear viscosity.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day