EN ISO 11125-1:2018

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:2018)

This document specifies a method for the sampling of metallic blast-cleaning abrasives from consignments and for the subdivision of the sample into quantities suitable for undertaking the appropriate test methods specified in other parts of ISO 11125.
This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning.
The types of metallic abrasive and requirements for each are contained in the various parts of ISO 11124.
The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Prüfverfahren für metallische Strahlmittel - Teil 1: Probenahme (ISO 11125-1:2018)

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Méthodes d'essai pour abrasifs métalliques destinés à la préparation par projection - Partie 1: Échantillonnage (ISO 11125-1:2018)

Le présent document spécifie une méthode pour l'échantillonnage des abrasifs métalliques destinés à la préparation par projection et provenant d'un lot, et pour la subdivision de l'échantillon en quantités appropriées permettant d'appliquer les méthodes d'essai appropriées spécifiées dans les autres parties de l'ISO 11125.
Il s'agit de l'une des parties de l'ISO 11125 traitant de l'échantillonnage et des essais des abrasifs métalliques destinés à la préparation par projection.
Le type d'abrasifs métalliques et les exigences pour chacun sont donnés dans les différentes parties de l'ISO 11124.
Les séries de normes ISO 11124 et ISO 11125 constituent une série cohérente de Normes internationales sur les abrasifs métalliques destinés à la préparation par projection. L'Annexe A donne des informations sur toutes les parties des deux séries.

Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne metode za kovinske granulate za peskanje - 1. del: Vzorčenje (ISO 11125-1:2018)

Ta dokument določa metodo za vzorčenje kovinskih granulatov za peskanje iz pošiljk in za razdelitev vzorca na količine, ustrezne za izvajanje ustreznih preskusnih metod, določenih v drugih delih standarda ISO 11125.
To je eden od več delov standarda ISO 11125, ki obravnavajo vzorčenje in preskušanje kovinskih granulatov za peskanje.
Vrste kovinskega granulata in zahteve za vsak granulat so določene v različnih delih
standarda ISO 11124.
Skupini standardov ISO 11124 in ISO 11125 sta bili pripravljeni kot skladen sklop mednarodnih standardov za kovinske granulate za peskanje. Informacije o vseh delih obeh skupin so podane v dodatku A.

General Information

• Status: Published
• Publication Date: 30-Oct-2018
• Withdrawal Date: 29-Apr-2019
• ICS: 25.220.10 - Surface preparation
• ICS: 87.020 - Paint coating processes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 31-Oct-2018
• Completion Date: 31-Oct-2018
• Ref Project: SIST EN ISO 11125-1:2018 - Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:2018)

Relations

• Replaces: EN ISO 11125-1:1997 - Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:1993)
• Effective Date: 11-Jun-2014

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 11125-1:1997
3ULSUDYDMHNOHQLKSRGODJSUHGQDQDãDQMHPEDUYLQVRURGQLKSUHPD]RY3UHVNXVQH
PHWRGH]DNRYLQVNHJUDQXODWH]DSHVNDQMHGHO9]RUþHQMH,62
Preparation of steel substrates before application of paints and related products - Test
methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:2018)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Prüfverfahren für metallische Strahlmittel - Teil 1: Probenahme (ISO 11125-1:2018)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes d'essai pour abrasifs métalliques destinés à la préparation par
projection - Partie 1: Échantillonnage (ISO 11125-1:2018)
Ta slovenski standard je istoveten z: EN ISO 11125-1:2018
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11125-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 25.220.10 Supersedes EN ISO 11125-1:1997
English Version
Preparation of steel substrates before application of paints
and related products - Test methods for metallic blast-
cleaning abrasives - Part 1: Sampling (ISO 11125-1:2018)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Méthodes d'essai von Beschichtungsstoffen - Prüfverfahren für
pour abrasifs métalliques destinés à la préparation par metallische Strahlmittel - Teil 1: Probenahme (ISO
projection - Partie 1: Échantillonnage (ISO 11125- 11125-1:2018)
1:2018)
This European Standard was approved by CEN on 13 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11125-1:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11125-1:2018) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11125-1:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11125-1:2018 has been approved by CEN as EN ISO 11125-1:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11125-1
Second edition
2018-09
Preparation of steel substrates before
application of paints and related
products — Test methods for metallic
blast-cleaning abrasives —
Part 1:
Sampling
Préparation des subjectiles d'acier avant application de peintures et
de produits assimilés — Méthodes d'essai pour abrasifs métalliques
destinés à la préparation par projection —
Partie 1: Échantillonnage
Reference number
ISO 11125-1:2018(E)
©
ISO 2018
ISO 11125-1:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 11125-1:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 2
5 Procedure. 2
5.1 General . 2
5.2 Number of sample units . 2
5.3 Sampling of sample units . 3
5.3.1 Pallets with bags, boxes or similar . 3
5.3.2 Drums, bulk sacks or similar . 3
5.4 Reduction of sample size . 4
5.5 Test sample . 4
6 Sample identification . 4
Annex A (informative) International Standards for metallic blast-cleaning abrasives .6
Bibliography . 7
ISO 11125-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International
...