EN 12972:2001
(Main)Tanks for transport of dangerous goods - Testing, inspection and marking of metallic tanks
Tanks for transport of dangerous goods - Testing, inspection and marking of metallic tanks
This European Standard specifies testing, inspection and marking for the type approval, initial inspection, periodic
inspection, intermediate inspection and exceptional check of metallic tanks (shell and equipment) of road tank
vehicles, rail tank wagons, portable tanks and tank containers for the transport of dangerous goods with a capacity
of more than 450 litres.
This European Standard is not applicable to
receptacles including gas cylinders,
battery-vehicles and battery-wagons comprising cylinders, tubes, pressure drums, bundles of cylinders, and
multiple element gas cylinders (MEGC), and
intermediate bulk containers (IBCs).
Tanks für die Beförderung gefährlicher Güter - Prüfung, Inspektion und Kennzeichnung von Metalltanks
Diese Europäische Norm legt die Prüfung, Inspektion und Kennzeichnung für die Baumusterprüfung, die erstmalige Prüfung, die wiederkehrende Prüfung, die Zwischenprüfung und die außenordentliche Prüfung von Metalltanks (Wandung und Ausrüstung) für die Beförderung gefährlicher Güter mit einem Volumen von mehr als 450 Litern fest. Diese Europäische Norm gilt nicht für Gefäße und Gasflaschen.
Citernes destinées au transport de marchandises dangereuses - Essai, épreuve, inspection et marquage des citernes métalliques
La présente norme européenne spécifie les essais et épreuves, les inspections et le marquage destinés à l'agrément de type, l'inspection initiale, l'inspection périodique, l'inspection intermédiaire et la vérification exceptionnelle des citernes métalliques (réservoirs et équipements) destinées au transport de marchandises dangereuses, ayant une capacité de plus de 450 litres. La présente norme européenne n'est pas applicable aux réceptacles et aux bouteilles à gaz comprimé.
Rezervoarji za transport nevarnega blaga - Preskušanje, nadzor in označevanje kovinskih rezervoarjev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tanks für die Beförderung gefährlicher Güter - Prüfung, Inspektion und Kennzeichnung von MetalltanksCiternes destinées au transport de marchandises dangereuses - Essai, épreuve, inspection et marquage des citernes métalliquesTanks for transport of dangerous goods - Testing, inspection and marking of metallic tanks23.020.20Posode in vsebniki, montirani na vozilaVessels and containers mounted on vehicles13.300Varstvo pred nevarnimi izdelkiProtection against dangerous goodsICS:Ta slovenski standard je istoveten z:EN 12972:2001SIST EN 12972:2002en01-maj-2002SIST EN 12972:2002SLOVENSKI
STANDARD
SIST EN 12972:2002
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12972April 2001ICS 13.300; 23.020.20English versionTanks for transport of dangerous goods - Testing, inspectionand marking of metallic tanksCiternes destinées au transport de matières dangereuses -Epreuve, inspection et marquage des citernes métalliquesTanks für die Beförderung gefährlicher Güter - Prüfung,Inspektion und Kennzeichnung von MetalltanksThis European Standard was approved by CEN on 22 February 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12972:2001 ESIST EN 12972:2002
Page 2EN 12972:2001ContentsPageForeword. 3Introduction. 31 Scope. 32 Normative references. 43
Terms and definitions. 54 Types of tank inspection. 64.1Inspection for type approval. 64.2Initial inspection. 74.3 Periodic inspection. 84.4 Intermediate inspection. 84.5
Exceptional checks. 95 Units used for tank inspection .105.1General105.2 Inspection of the necessary documents .115.3 Verification of the tank against the design 145.4 Inspection of the tank interior. 155.5 Inspection of the tank exterior. 165.6 Hydraulic pressure test .165.7 Vacuum testing. 185.8 Leakproofness test .195.9 Determination of water capa-city .205.10 Inspection of service equip-ment. 205.11 Inspection of frame or other struc-tural equipment of portable tanks. 205.12Test report, certification andmarking. 21Annex A
(informative) Example for a data sheet according to 4.1.3. 22Annex B (informative) Certificate of initial, periodic, intermediateinspection and exceptional check. 23PageAnnex C
(informative)Pressure testing with gases – hazards and precautions. 24Annex D (normative)Tank plates for tanks of road tankers for the transport of dangerous goods. 26Annex E
(normative) Tank plates for portable tanks and tank containers for the transport of dangerous goods. 28Annex F
(informative) Survey Table. 31SIST EN 12972:2002
Page 3EN 12972:2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 296 "Tanks for transport of dangerousgoods", the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or byendorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latest byOctober 2001.This European Standard has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports the objectives of the framework Directives on Transport of DangerousGoods.The standard has been submitted for reference into the RID1) and/or in the technical annexes of the ADR2).Therefore the standards listed in the normative references and covering basic requirements of the RID/ADR notaddressed within the present standard are normative only when the standards themselves are referred to in the RIDand/or in the technical annexes of the ADR.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countriesare bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France,Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland andthe United Kingdom.IntroductionThe frequencies of the different types of tank inspection are given by the relevant regulations concerning the transportof dangerous goods.1
ScopeThis European Standard specifies testing, inspection and marking for the type approval, initial inspection, periodicinspection, intermediate inspection and exceptional check of metallic tanks (shell and equipment) of road tank vehicles,rail tank wagons, portable tanks and tank containers for the transport of dangerous goods with a capacity of more than450 litres.This European Standard is not applicable to – receptacles including gas cylinders,– battery-vehicles and battery-wagons comprising cylinders, tubes, pressure drums, bundles of cylinders, andmultiple element gas cylinders (MEGC), and– intermediate bulk containers (IBCs).
1) May be purchased from: Zentralamt für den internationalen Eisenbahnverkehr OCTI, Gryphenhübeliweg, CH-3006 Bern
2) May be purchased from United Nations Sales Section, Geneva, or bookstores and distributors of United Nations Publications.SIST EN 12972:2002
Page 4EN 12972:20012
Normative referencesThis European standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. For datedreferences, subsequent amendments to or revisions of any of these publications apply to this European standard onlywhen incorporated in it or by amendment or revision. For undated references the latest edition of the publicationreferred to applies (including amendments).EN 287–1 : 1992Approval testing of welders - Fusion welding - Part 1: Steels EN 287–2 : 1992Approval testing of welders - Fusion welding - Part 2: Aluminium and aluminium alloysprEN 287–3 : 1995Approval testing of welders - Fusion welding - Part 3: Copper and copper alloysprEN 287–4 : 1995Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloysEN 288–1Specification and approval of procedures for welding metallic materials - Part 1: General rules for fusion weldingEN 288–2Specification and approval of procedures for welding metallic materials - Part 2: Welding procedure specification forarc weldingEN 288–3Specification and approval of procedures for welding metallic materials - Part 3: Welding procedure tests for the arcwelding of steelEN 837–2Pressure gauges – Part 2: Selection and installation recommendations for pressure gauges prEN 12266-1 : 1999Industrial valves - Testing of valves - Part 1: Tests, test procedures and acceptance criteria to be fulfilled by everyvalveEN 12561-1Railway applications - Tank wagons - Part 1: Marking of tank wagons for the carriage of dangerous goodsSIST EN 12972:2002
Page 5EN 12972:20013
Terms and definitionsThe definition of terms used in this standard shall be taken as those given by the relevant regulations concerning thetransport of dangerous goods unless otherwise stated.For the purposes of this European standard, the following additional terms and definitions apply:3.1 inspectorindividual or a body approved by the competent authority to perform designated inspections and tests3.2
intermediate inspectioninspection carried out between the initial and the first periodic inspection or between two periodic inspections3.3
portable tankmultimodal tank meeting the design and construction requirements defined in chapter 6.7 of the UN Model Regulationson the transport of dangerous goods. These requirements are reproduced in chapter 6.7 of the technical annexes ofADR and RID3.4tank containermultimodal tank meeting the design and construction requirements defined in chapter 6.8 of the technical annexes ofADR and RID3.5
protective lining or coatinglining or coating protecting the metallic tank material against the corrosive attack by the substances to be transportedThis does not apply to lining or coating used only to protect the substance to be transported.3.6repaircorrection of a defect which may have impaired the safety of the tank or the equipment. It does not include normalservice and maintenance operations of the shell or service equipment or replacement of gaskets or service equipmentto the same specification.3.7
technical codecode according to which the tank has been designed and constructed4
Types of tank inspection4.1
Inspection for type approval4.1.1
GeneralThe inspection for type approval shall be carried out on a single tank for an individual approval or approval of a rangeof tanks.A type approval which includes a range of tanks will allow the following variations to the design without requiring a newapproval, if there are no other conflicting technical or legal requirements:– a decrease in the initial design temperature range;SIST EN 12972:2002
Page 6EN 12972:2001– a decrease in the maximum gross mass;– a reduction in volume only resulting from variations in diameter (not applicable to non-cylindrical tanks) and length;the approval file includes a calculation for each proposed diameter, length and number of compartments of the tankunder the most unfavourable conditions, i.e.:× greatest density of goods,× greatest tank length and diameter,. greatest tank front compartment,. greatest tank rear compartment;– a variation in the grade of the material used; in the case of austenitic steels and aluminium alloys different gradesmay be allowed with the following reserves:. use of the same qualified welding procedure;. calculation is carried out in the most unfavourable case, in particular the mechanical characteristics selected arefor each element the lowest values of the grades used;. the instruction manual specifies the alternatives for the compatibility with the substances being transported;– movement or modification of nozzles and manholes provided that the same level of protection is afforded and thetank strength calculation takes into account the most unfavourable case;– an increase of the number of baffles and surge plates;– an increase of the wall thickness provided the same welding procedures are used;– a decrease of the maximum (allowable) working pressure (not valid for portable tanks subject to the IMDG Code);– an increase in the thickness of the insulation used for additional protection;– an increase in the effectiveness of the thermal insulation of the tank;– use of alternative service equipment if there is no change in the technical specification of the equipment and it isplaced in the same location.4.1.2Content of inspectionThe inspection for type approval shall be carried out in accordance with the following clauses: – examination of documents (see 5.2.);– verification of the tank against the design (see 5.3);– inspection of the tank interior (see 5.4);– inspection of the tank exterior (see 5.5);– hydraulic pressure test (see 5.6);– vacuum test (see 5.7, for tanks which fall within the scope of directive 94/63 EC);– leakproofness test (see 5.8);– determination of water capacity (see 5.9);– inspection of service equipment (see 5.10);– inspection of frame or other structural equipment of portable tanks (see 5.11).SIST EN 12972:2002
Page 7EN 12972:20014.1.3
DocumentationThe results of the inspection for type approval shall be recorded by the inspector in a test report.A preliminary report may be issued after examination of the documents.In addition to the test report it is recommended that the inspector submits a data sheet to assist the issuing of typeapproval. It is recommended that this data sheet form an annex to the type approval certificate.4.2
Initial inspection4.2.1
Content of inspectionThe initial inspection shall be carried out in accordance with the following clauses:– examination of documents (see 5.2.2);– verification of the tank against the design (see 5.3);– inspection of the tank interior (see 5.4);– inspection of the tank exterior (see 5.5);– hydraulic pressure test (see 5.6);– leakproofness test (see 5.8);– determination of water capacity (see 5.9);– inspection of service equipment (see 5.10);– inspection of frame or other structural equipment of portable tanks (see 5.11).4.2.2
Documentation, certification and markingThe results of the initial inspection shall be recorded by the inspector in a certificate. This certificate shall mention anysignificant defect found and the related repairs carried out. It is acceptable for the certificate of initial inspection of atank which has been tested for type approval to be completed using the results of the inspection for type approval. Forcertification and marking 5.12 shall be applied.SIST EN 12972:2002
Page 8EN 12972:20014.3
Periodic inspection4.3.1
Content of inspectionThe periodic inspection shall be carried out in accordance with the following clauses:– examination of documents (see 5.2.3);– inspection of the tank interior (see 5.4);– inspection of the tank exterior (see 5.5);– hydraulic pressure test (see 5.6);– leakproofness test (see 5.8);– inspection of service equipment (see 5.10);– inspection of frame or other structural equipment of portable tanks (see 5.11).For vacuum insulated tanks the inspection of the tank interior and the hydraulic pressure test are not required providedthat a satisfactory vacuum is confirmed by measurement. 4.3.2
Documentation, certification and markingThe results of the periodic inspection shall be recorded by the inspector in a certificate. This certificate shall mentionany significant defect found and the related repairs carried out. For certification and marking 5.12 shall be applied.4.4
Intermediate inspection4.4.1
Content of inspectionThe intermediate inspection shall be carried out in accordance with the following clauses:– examination of documents (see 5.2.4);– inspection of the tank interior (see 5.4; only where required by regulation);– inspection of the tank exterior (see 5.5);– leakproofness test (see 5.8);– inspection of service equipment (see 5.10).– inspection of frames or other structural equipment of portable tanks (see 5.11; only where required by regulation).4.4.2
Documentation, certification and markingThe results of the intermediate inspection shall be recorded by the inspector in a certificate. This certificate shallmention any significant defect found and the related repairs carried out. For certification and marking 5.12 shall beapplied.SIST EN 12972:2002
Page 9EN 12972:20014.5
Exceptional checks4.5.1
Exceptional check after damage or repair of the tankThe exceptional check after damage of the tank which may have impaired the safety of the shell, or after repair, shallbe carried out in accordance with the applicable clauses as listed:– examination of documents (see 5.2.5); – verification of the tank against the design (see 5.3);– inspection of the tank interior (see 5.4);– inspection of the tank exterior (see 5.5);– hydraulic pressure test (see 5.6);– leakproofness test (see 5.8);– inspection of service equipment (see 5.10).4.5.2
Exceptional check after repair or replacement of service equipmentThe exceptional check after repair or replacement of the service equipment shall be carried out in accordance with theapplicable clauses as listed:– examination of documents (see 5.2.5);– verification of the tank against the design (see 5.3);– leakproofness test (see 5.8);– inspection of service equipment (see 5.10).4.5.3
Exceptional check after replacement of service equipment involving the application of heatThe exceptional check after exchange of the service equipment involving the application of heat (for instance welding,cutting) which may have impaired the safety of the tank or the service equipment shall be carried out in accordancewith the applicable clauses as listed:– examination of documents (see 5.2.5);– verification of the tank against the design (see 5.3);– hydraulic pressure test (see 5.6); – leakproofness test (see 5.8);– inspection of service equipment (see 5.10).4.5.4
Exceptional check after alteration to the tankIf there is an alteration to the tank not in accordance with the type approval the applicable units of the inspection fortype approval shall be reassessed.SIST EN 12972:2002
Page 10EN 12972:20014.5.5
Exceptional check after exchange or repair of frame or structural equipmentThe exceptional check after exchange or repair of frame or structural equipment shall be carried out in accordance withthe applicable clauses as listed:– examination of documents (see 5.2.5);– verification of the tank against the design (see 5.3);– inspection of frame or other structural equipment of portable tanks (see 5.11).The requirements of this subclause can be considered to be fulfilled if the tank container which is covered by theInternational Convention for Safe Containers (CSC) has been examined and/or tested in accordance with therequirements of CSC.4.5.6
Exceptional check before and after repair or replacement of the protective lining or coating The exceptional check before and after repair or replacement of the protective lining or coating whose defect mayimpair the safety of the tank shall be carried out in accordance with the applicable clauses as listed:– examination of documents (see 5.2.5);– inspection of the tank interior (see 5.4)4.5.7
Exceptional check to allow amendment of the type approval The exceptional check to allow the amendment of the type approval shall be carried out as a reassessment of therespective applicable items of the inspection for type approval.4.5.8
Documentation, certification and markingThe results of the exceptional check shall be recorded by the inspector in a certificate. This certificate shall mention anysignificant defects found and the related repairs carried out. For certification and marking 5.12 shall be applied.A preliminary report can be issued after examination of documents.5
Units used for tank inspection5.1
GeneralA tank which fails one or more units of inspection shall, once the reason for failure has been corrected, be retested inaccordance with the requirements of those units. The retest shall consider the need for additional testing if the repairmay affect the validity of the result of other previous tests.Depending on the result of the inspections additional inspections may be necessary.The tanks to be internally inspected shall be empty, clean, certified gas-free and safe to enter at the time of inspection.This is also a requirement when necessary for the safety of the inspecting personnel and any other persons in thevicinity even when other inspections are carried out.Gas-free means that the concentration of gases in the tank which may influence the health or safety of the inspectingpersonnel and any other persons in the vicinity is within the allowed limits of the national regulations applicable to them.SIST EN 12972:2002
Page 11EN 12972:20015.2
Examination of documents 5.2.1
Inspection for type approval5.2.1.1
Required documentsThe documents shall provide the following information for the inspection for type approval:– name and address of the applicant;– description of the tank prototype including planned variations to the design and its special characteristics; – names and addresses of the manufacturer and the assembler of the tank; in the case of road tank vehicles orrail tank wagons the design of chassis or wagon; in the case of portable tanks the manufacturer and design offrame if applicable; – certificate of welder and welding procedure qualification in accordance with the technical code; when the technicalcode does not contain requirements for qualification of the welder and welding procedure the requirements of therelevant parts of EN 287 and EN 288 shall apply; – description of the assigned mode of operation (e. g. pressure discharging);– listing of all dangerous goods or groups of goods to be transported by the tank indicating the substance with thehighest vapour pressure at the relevant reference temperature as well as the substance with the highest density at15 °C and 50 °C or at the operating temperature if higher, and indicating the respective values.– schematic drawing of the tank with listing of main dimensions; – schematic drawings of the piping systems;– data sheet with the operational data of the tank necessary for calculation;– calculation and, if required, verification by testing of the tank and its fastenings;– drawings necessary for verifying the manufacture of the tank, of its equipment and of its fastenings, including anassembly drawing and a parts list indicating the materials;– drawings for marking (tank plates and others);– listing of the service equipment with the relevant technical data;– suitability of the safety equipment including the calculation of the relief capacity if relevant; – certificate showing values of material properties used for tank and equipment as required by the technical code;– record of tests carried out on production control test plates (the test plates shall be inspected by an expert) ifrequired by the technical code and/or the relevant regulations concerning the transport of dangerous goods;– when using a protective lining or coating, proof that the protective lining or coating has been applied inaccordance with the manufacturer's specification;– qualification certificate for personnel undertaking non-destructive test (NDT);– certificate of the base materials and welding filler materials;– recording of the heat treatments.SIST EN 12972:2002
Page 12EN 12972:20015.2.1.2
Examination of documents The documents shall be examined to ensure that the requirements of the relevant dangerous goods regulations andtechnical code have been fulfilled. The compatibility of tank material and equipment with the assigned dangerous goodsshall be verified.5.2.2
Initial inspection5.2.2.1
Required documentsThe documents shall provide the following information for the initial inspection:– application for initial inspection;– type approval certificate;– information given in the application of type approval where necessary (see 5.2.1.1);– certificate of welder and welding procedure qualification in accordance with the technical code; when the technicalcode does not contain requirements for qualification of the welder and welding procedure the requirements of therelevant parts of EN 287 and EN 288 shall apply; – certificate showing values of material properties used for tank and equipment as required by the technical code;– record of the non destructive testing carried out on the welds;– record of tests carried out on production control test plates (the test plates shall be inspected by an expert) ifrequired by the technical code and/or the relevant regulations concerning the transport of dangerous goods;– when using a protective lining or coating, proof that the protective lining or coating has been applied inaccordance with the manufacturer's specification;– qualification certificate for personnel undertaking non-destructive test (NDT);– certificate of the base materials and welding filler materials;– recording of the heat treatments.5.2.2.2
Examination of documentsThe documents shall be examined to ensure compliance with the type approval and that the requirements of therelevant dangerous goods regulations and the technical code have been fulfilled.5.2.3
Periodic inspection5.2.3.1
Required documentsThe following documents or copies of them shall be provided for the periodic inspection:– certificate of initial inspection if the tank has not been subject to periodic inspection;– certificate of last periodic inspection, if applicable;– certificate of intermediate inspection if carried out after the previous periodic inspection or after the initialinspection if there has been no periodic inspection;– if required one or more of the documents mentioned in 5.2.1.1.SIST EN 12972:2002
Page 13EN 12972:20015.2.3.2
Examination of documentsThe documents shall be examined to ensure that they are relevant to the tank to be examined. Any additionalrequirements and remarks given in these documents shall be taken into account.5.2.4
Intermediate inspection5.2.4.1
Required documentsThe following documents or copies of them shall be provided for the intermediate inspection: – certificate of initial inspection if the tank has not been subject to periodic inspection;– certificate of last periodic inspection;– if required the documents mentioned in 5.2.1.1.5.2.4.2
Examination of documentsThe documents shall be examined to ensure that they are relevant to the tank to be examined. Any additionalrequirements and remarks given in these documents shall be taken into account.5.2.5
Exceptional check5.2.5.1
Required documentsAs far as it is relevant for the exceptional checks described in 4.5.1 to 4.5.7 the documents shall provide the followinginformation:– copy of certificate of type approval authenticated by the sender;– information given in the application of type approval where necessary (see 5.2.1.1);– name and address of the workshop carrying out the alteration to the tank or the repair; – certificate of welder and welding procedure qualification in accordance with the technical code; when the technicalcode does not contain requirements for qualification of the welder and welding procedure the requirements of therelevant parts of EN 287 and EN 288 shall apply;– recording of the heat treatments;– proof that the properties of the materials used for a repair or alteration to the tank are at least equivalent to thoseof the materials used for the original construction;– record of the non destructive testing carried out;– if welding is carried out, a record of tests performed on the production control test plates (the test plates shall beinspected by an expert) if required by the technical code; and/or the relevant regulations concerning the transportof dangerous goods.– when using a protective lining or coating, proof that the protective lining or coating has been applied inaccordance with the manufacturer's specification;– if necessary for repair of service equipment, a schematic drawing of the piping systems;– if piping is changed, schematic drawings of the piping systems;– a description of work carried out.SIST EN 12972:2002
Page 14EN 12972:2001The documents shall provide the following relevant information for the exceptional check described in 4.5.6:– proof of compatibility of the protective lining or coating with the dangerous goods to be transported;– proof that the protective lining or coating has been applied in accordance with the manufacturer's specification.5.2.5.2
Examination of documentsThe documents shall be examined to ensure that the requirements of the relevant dangerous goods regulations andthe technical code are fulfilled.5.3
Verification of the tank against the design5.3.1
Content of inspectionThe verification of the tank against the design includes:– Examination of the manufacturing conditions;– Inspection of the material grades and wall thicknesses;– Inspection of the manufacturing methods;– Inspection of the condition of the tank;– Inspection of the main dimensions;– Non-destructive testing of the welds.A reference to type approval documents shall be taken to mean the design documents when the verification is forthe purpose of type approval (see 5.2.1.1).5.3.2
Examination of the manufacturing conditionsThe qualification of the manufacturing equipment and personnel as well as the proof of the qualification shall be asrequired by the technical code.5.3.3
Inspection of the materials and wall thicknessesThe materials used for the shell, the piping and the structural and service equipment shall correspond to the typeapproval and with the material certificates, where appropriate. The material certificates shall be as required by thetechnical code. The tank shall be inspected to guarantee that the traceability between the marking of the materials and the identifica-tion given by the respective material certificates is properly ensured.The actual thickness of materials of the shell, the piping and the structural equipment shall not be less than that givenby the type approval documents. This shall be verified by appropiate measurement on completion of the tank.5.3.4
Examination of the manufacturing methodsThe manufacturing methods and data of the heat treatment, the rolling and the forming of the materials used for theshell, the piping and the structural equipment shall correspond to the methods and respective data of the designdocuments of the tank.The type of welded joints shall correspond to the design of the tank.SIST EN 12972:2002
Page 15EN 12972:20015.3.5
Inspection of the conditio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.