EN 10244-6:2001
(Main)Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 6: Copper, bronze or brass coatings
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 6: Copper, bronze or brass coatings
This part of this European Standard specifies the requirements for mass, other properties and testing of copper, bronze and brass coatings on steel wire and steel wire products.
Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil 6: Überzüge aus Kupfer, Bronze oder Messing
Dieser Teil der Europäischen Norm legt die Anforderungen an Masse, andere Eigenschaften und Prüfung von Kupfer-, Bronze- und Messing-Überzügen auf Stahldraht und Stahldrahterzeugnissen fest.
Fils et produits tréfilés en acier - Revêtements métalliques non ferreux sur fils d'acier - Partie 6: Revêtements de cuivre, bronze ou laiton
Domaine d'application
La présente partie de la présente norme européenne spécifie les exigences en matière de masse, des autres caractéristiques et d'essai de revêtements de cuivre, en bronze ou en laiton sur fils en acier et produits dérivés.
Jeklena žica in žični izdelki - Neželezne kovinske prevleke na jekleni žici - 6. del: Bakrene, bronaste ali medne prevleke
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2002
-HNOHQDåLFDLQåLþQLL]GHONL1HåHOH]QHNRYLQVNHSUHYOHNHQDMHNOHQLåLFLGHO
%DNUHQHEURQDVWHDOLPHGQHSUHYOHNH
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 6:
Copper, bronze or brass coatings
Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil
6: Überzüge aus Kupfer, Bronze oder Messing
Fils et produits tréfilés en acier - Revetements métalliques non ferreux sur fils d'acier -
Partie 6: Revetements de cuivre, bronze ou laiton
Ta slovenski standard je istoveten z: EN 10244-6:2001
ICS:
25.220.40 Kovinske prevleke Metallic coatings
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 10244-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2001
ICS 25.220.40
English version
Steel wire and wire products - Non-ferrous metallic coatings on
steel wire - Part 6: Copper, bronze or brass coatings
Fils et produits tréfilés en acier - Revêtements métalliques Stahldraht und Drahterzeugnisse - Überzüge aus
non ferreux sur fils d'acier - Partie 6: Revêtements de Nichteisenmetall auf Stahldraht - Teil 6: Überzüge aus
cuivre, bronze ou laiton Kupfer, Bronze oder Messing
This European Standard was approved by CEN on 21 January 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10244-6:2001 E
worldwide for CEN national Members.
Page 2
Contents
Page
Foreword .3
1 Scope.4
2 Normative reference.4
3 Terms and definitions.4
4 Requirements relating to coating.5
4.1 Material.5
4.2 Coating mass.5
4.3 General .5
4.4 Porosity .5
5 Test conditions.5
5.1 Samples.5
5.1.1 General .5
5.1.2 Length of samples.5
5.2 Determination of mass of coating .5
5.2.1 General .5
5.2.2 Gravimetric method .5
5.2.3 Use of chemical methods for determining coating mass .6
5.3 Porosity .6
5.3.1 Principle .6
5.3.2 Determination of the porosity.6
Page 3
Foreword
This European Standard has been prepared by Technical Committee ECISS/TC 30 "Steel wires", the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2001, and conflicting national standards
shall be withdrawn at the latest by September 2001.
This European Standard for non-ferrous metallic coating on steel wire is made up of the following
parts:
Part 1 : General principles
Part 2 : Zinc and zinc alloy coatings
Part 3 : Aluminium coatings
Part 4 : Tin coatings
Part 5 : Nickel coatings
Part 6 : Copper, bronze and brass coatings
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portuga
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.