Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity

This document gives guidance for requirements for the assessment of conformity of materials (compounds/formulations), products, joints and assemblies in accordance with the applicable part(s) of EN 13598-1 and EN 13598-2 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   The quality management system is expected to conform to or be no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If certification is involved, the certification body is expected to be compliant with EN ISO/IEC 17065 [5].
NOTE 3   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 13598-1 and EN 13598-2 (see Foreword) this document is applicable to ancillary fittings including shallow chambers and manholes and inspection chambers.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 3: Empfehlungen für die Beurteilung der Konformität

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVCU), polypropylène (PP) et polyéthylène (PE) - Partie 3: Évalution de la conformité

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U), polipropilen (PP) in polietilen (PE) - 3. del: Ugotavljanje skladnosti

Ta tehnična specifikacija vsebuje navodila za ugotavljanje skladnosti spojin/formulacij, izdelkov in sestavov s 1. in 2. delom standarda EN 13598, pri čemer naj bi se te informacije vključile v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja, ki ga izvajajo tretje osebe.
OPOMBA:   V pomoč bralcem dodatka A in B vsebujeta osnovno preskusno matriko.
Ta tehnična specifikacija se v povezavi s standardoma EN 13598-1 in EN 13598-2 uporablja za pomožne fitinge za odvodnjavanje, ki so položeni v zemljo, vključno z jaški in revizijskimi komorami:
–   za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo zunaj stavbne konstrukcije (koda območja uporabe »U«), kar je na izdelkih označeno z »U«; in
–   za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo znotraj stavbne konstrukcije (koda območja uporabe »D«) ali zunaj nje (koda območja uporabe »U«), kar je na izdelkih označeno z »UD«.

General Information

Status
Published
Publication Date
23-Nov-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Nov-2021
Due Date
07-Nov-2022
Completion Date
24-Nov-2021

Relations

Buy Standard

Technical specification
TS CEN/TS 13598-3:2022
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 13598-3:2022
01-januar-2022
Nadomešča:
SIST-TS CEN/TS 13598-3:2012

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo

po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-
U), polipropilen (PP) in polietilen (PE) - 3. del: Ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -

Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -

Part 3: Assessment of conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und
Polyethylen (PE) - Teil 3: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs

d'assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVCU),

polypropylène (PP) et polyéthylène (PE) - Partie 3: Évalution de la conformité
Ta slovenski standard je istoveten z: CEN/TS 13598-3:2021
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST-TS CEN/TS 13598-3:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 13598-3:2022
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
November 2021
TECHNISCHE SPEZIFIKATION
ICS 93.030; 23.040.05 Supersedes CEN/TS 13598-3:2012
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
3: Assessment of conformity

Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte

branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -

enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),

plastifié (PVCU), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 3:

(PE) - Partie 3: Évalution de la conformité Empfehlungen für die Beurteilung der Konformität

This Technical Specification (CEN/TS) was approved by CEN on 17 October 2021 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to

submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS

available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in

parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 13598-3:2021 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
Contents Page

European foreword ....................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1 Scope .................................................................................................................................................................... 5

2 Normative references .................................................................................................................................... 5

3 Terms and definitions ................................................................................................................................... 5

4 Abbreviated terms and symbols ................................................................................................................ 9

5 General ................................................................................................................................................................ 9

6 Testing (EN 13598-1) ..................................................................................................................................... 9

6.1 Group ................................................................................................................................................................... 9

6.1.1 General ................................................................................................................................................................ 9

6.1.2 Size groups ......................................................................................................................................................... 9

6.1.3 Fitting groups ................................................................................................................................................ 10

6.2 Type testing .................................................................................................................................................... 10

6.2.1 General ............................................................................................................................................................. 10

6.2.2 Change of material – PVC-U ...................................................................................................................... 11

6.2.3 Change of material - Polypropylene ...................................................................................................... 12

6.2.4 Change of material - Polyethylene ......................................................................................................... 13

6.3 Batch release testing ................................................................................................................................... 17

6.4 Process verification testing ...................................................................................................................... 19

6.5 Audit testing ................................................................................................................................................... 21

6.6 Test records ................................................................................................................................................... 23

7 Testing (EN 13598-2) .................................................................................................................................. 23

7.1 Group ................................................................................................................................................................ 23

7.1.1 General ............................................................................................................................................................. 23

7.1.2 Size groups ...................................................................................................................................................... 23

7.1.3 Fitting groups ................................................................................................................................................ 24

7.2 Type testing .................................................................................................................................................... 24

7.2.1 General ............................................................................................................................................................. 24

7.2.2 Change of material – PVC-U ...................................................................................................................... 25

7.2.3 Change of material - Polypropylene ...................................................................................................... 26

7.2.4 Change of material - Polyethylene ......................................................................................................... 27

7.3 Batch release testing ................................................................................................................................... 32

7.4 Process verification testing ...................................................................................................................... 34

7.5 Audit testing ................................................................................................................................................... 36

7.6 Test records ................................................................................................................................................... 38

Annex A (informative) Basic test matrix .......................................................................................................... 39

Bibliography ................................................................................................................................................................. 43

---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
European foreword

This document (CEN/TS 13598-3:2021) has been prepared by Technical Committee CEN/TC 155

“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes CEN/TS 13598-3:2012.
Compared with CEN/TS 13598-3:2012, the following changes have been made:

— this document has been updated to comply with the latest CEN/TC 155 internal guide – Plastics

piping systems – Template for documents for the assessment of conformity;

— type testing clauses have been updated to clarify what constitutes a change of material. Examples of

a change of design, production processing method, extension of product range and system are also

given;

— the applicable characteristics for assessment of conformity testing are now listed under separate

Clauses 6 and 7 for EN 13598 parts 1 and 2 respectively;

— the tables in Clauses 6 and 7 have been updated to align the content and references with

EN 13598-1:2020 and EN 13598-2:2020.

EN 13598 consists of the following Parts under the general title Plastics piping systems for non-pressure

underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and

polyethylene (PE):
— Part 1: Specifications for ancillary fittings and shallow chambers;
— Part 2: Specifications for manholes and inspection chambers;
— Part 3: Guidance for assessment of conformity (the present document).

Any feedback and questions on this document should be directed to the users’ national standards body.

A complete listing of these bodies can be found on the CEN website.

According to the CEN/CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

Kingdom.
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
Introduction

This document details the applicable characteristics to be assessed for type testing (TT), batch release

test (BRT), process verification test (PVT), and audit test (AT), as well as the frequency and sampling for

testing.

This document has been prepared using the latest CEN/TC155/WG21 assessment of conformity template

N1089.

The concept of testing and organization of those tests used for the assessment of conformity is shown,

without or with certification, in Figures 1 and 2.

Figure 1 — Typical scheme for the assessment of conformity by a manufacturer, without

certification

Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including

certification
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
1 Scope

This document gives guidance for requirements for the assessment of conformity of materials

(compounds/formulations), products, joints and assemblies in accordance with the applicable part(s) of

EN 13598-1 and EN 13598-2 intended to be included in the manufacturer’s quality plan as part of the

quality management system and for the establishment of certification procedures.

NOTE 1 The quality management system is expected to conform to or be no less stringent than the relevant

requirements of EN ISO 9001 [1].

NOTE 2 If certification is involved, the certification body is expected to be compliant with EN ISO/IEC 17065 [5].

NOTE 3 A basic test matrix provides an overview of the testing scheme in Annex A.

In conjunction with EN 13598-1 and EN 13598-2 (see Foreword) this document is applicable to ancillary

fittings including shallow chambers and manholes and inspection chambers.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 13598-1:2020, Plastics piping systems for non-pressure underground drainage and sewerage -

Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications

for ancillary fittings and shallow chambers

EN 13598-2:2020, Plastics piping systems for non-pressure underground drainage and sewerage -

Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications

for manholes and inspection chambers
3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 13598-1 and EN 13598-2 and

the following apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
certification body

impartial body, governmental or non-governmental, possessing the necessary competence to carry out

certification of conformity according to given rules of procedure and management

Note 1 to entry: In this document, certification is understood as third-party certification.

Note 2 to entry: For assessment purposes, the certification body may delegate tasks to an inspection body or a

testing laboratory.
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
3.2
inspection body

body that performs examination of a product, process, service, or installation or their design and

determination of its conformity with specific requirements or, on the basis of professional judgment, with

general requirements

[SOURCE: EN ISO/IEC 17020:2012 [2], definition 3.5 combined with definition 3.1 modified – Notes to

entry 1, 2, 3 and 4 are not included]

Note 1 to entry: An inspection body is, either an organization or a part of an organization, mandated by the

certification body.

Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [2].

3.3
testing laboratory

laboratory which measures, tests, calibrates or otherwise determines the characteristics of the

performance of materials and products

Note 1 to entry: In the context of this document, the materials and products can be subjected to type testing, batch

release testing, process verification testing and audit testing, as applicable.

Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 [3].

3.4
quality management system
part of a management system with regard to quality
[SOURCE: EN ISO 9000:2015 [4], definition 3.5.4]

Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].

3.5
quality plan

document setting out the specific quality practices, responsibilities, resources and sequence of activities

relevant to a particular product or range of products
3.6
type testing

test performed to prove that the material, component, product, joint or assembly is capable of conforming

to the requirement(s) given in the relevant standard
3.7
batch release test
BRT

test performed on a batch of material, components products, joints or assemblies which has to be

satisfactorily completed before the batch can be released

Note 1 to entry: A batch release test may be performed by the manufacturer or outsourced on behalf of the

manufacturer.
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
3.8
process verification test
PVT

test performed on material, component, product, joint or assembly at specific intervals to confirm that

the process continues to be capable of producing products which conform to the requirements given in

the relevant standard

Note 1 to entry: Process verification tests are not required to release batches of material, product, but are carried

out as a measure of process control.

Note 2 to entry: Process verification tests may be performed by the manufacturer or outsourced on behalf of the

manufacturer.

Note 3 to entry: Process verification tests are regularly performed to demonstrate that the product remains.

compliant with the type test results
3.9
audit test
test performed on behalf of a certification body

Note 1 to entry: Audit tests are generally required to confirm that the formulation/compound, product, joint or

assembly continues to conform to the requirements given in the relevant standard and to provide information to

assess the effectiveness of the quality management system.
3.10
indirect test

batch release test performed which differs from that specified test for that particular characteristic,

having previously verified its correlation with the specified test

Note 1 to entry: Indirect tests may be performed by the manufacturer or outsourced on behalf of the

manufacturer.
3.11
witness test

type test or audit test which is performed in the presence of a representative of the certification body

3.12
material

generic term for compounds/formulations grouped by families, expressed by generic names

Note 1 to entry: Examples of generic names are PVC-U, polypropylene and EPDM.
3.13
substance

monomer, additive, element or chemical compound as used in compounds/formulations

---------------------- Page: 9 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
3.14
compound/formulation

clearly defined homogenous mixture of substances used for the manufacture of the product as defined in

the referring product standard

Note 1 to entry: In general, the term “compound” is used for polyolefins and the term “formulation” for PVC.

Note 2 to entry: The term “composition” is often used instead of compound/formulation for metals and when

dealing with water and food contact regulations.
3.15
material batch

clearly identified quantity of a given homogeneous compound/formulation manufactured under uniform

conditions and defined and identified by the compound/formulation manufacturer
3.16
product

item as defined in the scope of the standard, e.g. fitting, manhole or inspection chamber

3.17
product batch

clearly identified collection of products, manufactured consecutively or continuously under the same

conditions, using the same compound/formulation conforming to the same specification

3.18
sample

one or more components or products drawn from the same production batch selected at random without

regard to their quality
3.19
group

defined collection of similar components/products from which samples are selected for testing purposes

3.20
component
part of a product

Note 1 to entry: Depending on the context, components may be considered as products and be individually

approved (e.g. o-ring, gasket) or they are tested as integral part of a finished product (e.g. in a valve).

3.21
joint
connection between two products
3.22
assembled product
final product comprising two or more components
3.23
fabricated fitting

fitting produced by welding, thermoforming or solvent-cementing from pipes and/or from injection-

moulded [or rotomoulded] fittings
---------------------- Page: 10 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
3.24
assembly
set of various products assembled together for the purpose of testing
3.25
cavity
space within a mould to be filled to form the moulded product

EXAMPLE That part of an injection mould which gives the form to the injection moulded product

4 Abbreviated terms and symbols

To avoid misunderstanding, the abbreviations in this Clause are defined as being the same in each

language. For the same reason, the terms are given in the three languages, English, French and German.

EN FR DE
AT audit test essai d’audit Überwachungsprüfung

BRT batch release test essai de libération de campagne de Freigabeprüfung einer Charge

fabrication
PVT process essai de vérification du procédé de Prozessüberprüfung
verification test fabrication
TT type test essai de type Typprüfung
5 General

Materials, products and fitness for purpose shall conform to the requirements given in EN 13598-1 and

EN 13598-2.

Materials and products shall be produced by the manufacturer under a quality management system

which includes a quality plan.
6 Testing (EN 13598-1)
6.1 Group
6.1.1 General

For the purposes of this document, the groups specified in 6.1.2 and 6.1.3 apply.

6.1.2 Size groups

For ancillary fittings the size groups are defined in Table 1 and for shallow chambers in Table 2.

The nominal diameter of ancillary fittings (excluding mechanical saddles) shall be that of the pipe which

can be connected to its outlet.

Mechanical saddles are sized by the nominal diameter of the main pipe that they are intended to joint to.

---------------------- Page: 11 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
Table 1 — Size groups for ancillary fittings
Size group Nominal outside diameter, d
1 d ≤ 200
2 200 < d ≤ 500
3 d 500
n >

For shallow chambers, size relates to the nominal internal diameter (DN/ID) of the riser (see Table 2).

Table 2 — Size groups for shallow chambers
Size group Nominal inside diameter, d
1 180 < d ≤ 450
2 450 < d < 800
6.1.3 Fitting groups

For ancillary fittings and shallow chambers, the fitting groups are defined in Table 3.

Table 3 — Fitting groups for ancillary fittings and shallow chambers
Fitting group Type of fitting
1 Sealed access fittings
2 Rodding point covers
3 Rodding tees
4 Mechanical saddles
5 Shallow chambers
Each group shall consist of a range of products of the same material and design.
6.2 Type testing
6.2.1 General

Type testing is intended to demonstrate the ability of the product to fulfil the intended use and

characteristics detailed in the referring product standard.

Type testing shall be performed as described in Table 7 and Table 8 whenever there is:

a. a new system (N);
b. a change in design (D);
c. a change in material (M);
---------------------- Page: 12 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021

d. a change in production processing method (P), other than routine in-process adjustments;

e. and an extension of the product range (E).

NOTE 1 Type testing may need to be revalidated as a result of deviation of process verification test (see 6.4).

— An example of a new system (N) would be understood as a manufacturer’s first application for a new

fitting group in accordance with EN 13598-1 or a change to more than one of the other categories.

— An example of a change in design (D) would be understood as changes that only have an influence on

the jointing and/or performance characteristics of the fittings.

— An example of a change in production processing method (P) would be understood as a change in

production method from e.g. injection moulding to rotational moulding.

— An example of an extension of the product range (E) would be understood as an extension with a new

size group.

For a change of material (M), Clauses 6.2.2 to 6.2.4 apply. A change of generic material (e.g. PP to PE) is

considered as a new system (N).

When a change of production site occurs, the manufacturer shall determine which type tests need to be

revalidated.

Unless any of the conditions a) to e) above occurs, the type test results remain valid.

A type test may be performed by the manufacturer or outsourced on behalf of the manufacturer.

NOTE 2 If certification is involved, the certification body may request the location of the test.

Type tests shall demonstrate that the products conform to all requirements for the characteristics given

in Tables 7 and 8, as applicable.
6.2.2 Change of material – PVC-U

Each formulation, including if applicable non-virgin material, shall be specified by the manufacturer in

the quality plan, including the ingredients and their tolerances.

If the dosage level in the formulation exceeds the tolerance band given in Table 4, or if there is a change

of type, this variation is considered to be a change in material.

In Table 4, for the virgin part of the formulation the values of the parts X added to 100 parts by mass of

PVC shall be specified by the manufacturer in the quality plan.

For the non-virgin part of the formulation (if applicable) the part X shall be given as a % of the mass of

the virgin part.
---------------------- Page: 13 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021
Table 4 — Formulation tolerances
Ingredients Type Tolerance
Virgin part of the formulation
PVC resin Nominal K value as specified ±3 units
by the manufacturer
Type of stabilizer or 1) OBS (Organic Based X : ± 25 %
masterbatch Stabilizers)
2) Ca-Zn
3) Sn
4) Ca-Sn
5) Others
Lubricants All for X ≤ 0,2: X : ± 50 %
2 2
for X > 0,2: X : ± 0,1
2 2
phr
Fillers 1) CaCO X : ± 3 phr
3 3
2) Others X : ± 25 %
Impact modifiers All X : ± 1 phr
Flow agents All for X ≤ 2: X : ± 25 %
6 6
for X > 2: : ± 0,5 phr
6 X6
Pigments All No requirement
Non-virgin part of the formulation
Own reprocessed EN 13598-1:2020, Clause 5 No requirement
material
External reprocessed EN 13598-1:2020, Clause 5 ≤ X
and/or recycled
material with a defined
agreed specification

NOTE A change of the supplier does not necessarily constitute a change in formulation.

phr means parts per hundred resin.

The manufacturer quality plan shall allow the source and content of own reprocessed

material formulation to be demonstrated.

X7 shall not exceed the declared values as required in EN 13598-1:2020, Clause 5. This

means that a lower content of external reprocessed and/or recycled material in the

formulation which has already been type tested and which is fulfilling the agreed

specification is not considered as a material change.
6.2.3 Change of material - Polypropylene

Each compound, including if applicable non-virgin material, shall be specified by the manufacturer in the

quality plan, including the ingredients and their tolerances.

When a pigment masterbatch is used, it shall be considered as a change of compound if the type of

pigment carrier is changed.
---------------------- Page: 14 ----------------------
SIST-TS CEN/TS 13598-3:2022
CEN/TS 13598-3:2021

If the content of the mineral modifier by mass is higher than the measured content by mass at type testing

or a new type of mineral modifier is used, this shall be considered as a change of material.

In Table 5,the values of the parts X shall add up to 100 % by mass (excluding own reprocessed material)

and be specified by the manufacturer in the quality plan.
Table 5 — PP compound tolerances
Ingredients Type Tolerance
Virgin part of compound
PP Trade name X % ≥ as specified by
the manufacturer
Pigment masterbatch Pigment carrier No requirement
Mineral modifier (if 1) CaCO3 X % ≤ as specified by
applicable) the manufacturer
2) Talc
Non virgin part of compound
Own reprocessed EN 13598-1:2020, Clause 5 No requirement
material
External reprocessed EN 13598-1:2020, Clause 5 ≤ X %
and/or recycled
material with a defined
agreed specification
NOTE A chang
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.