EN ISO 6877:1998
(Main)Dental root-canal obturating points (ISO 6877:1995)
Dental root-canal obturating points (ISO 6877:1995)
Gives limit dimensions of thread for metal or plastic and ceramic lampholders with shade holder rings made of metal or plastic. Dimensions
Zahnärztliche Wurzelkanalfüllstifte (ISO 6877:1995)
In der vorliegenden internationalen Norm werden Maße und Anforderungen an die Zusammensetzung für vorgefertigte Stifte oder Kegel auf Metall- oder Kunststoffbasis, die als Wurzelkanalfüllungen, jedoch nicht als Wurzelstifte für Kronenrestaurationen verwendet werden, festgelegt. Diese Norm spezifiziert außerdem numerische Systeme und ein Farbkennzeichnungssystem zur Größenbezeichnung. Zusätzlich zu den für das Produkt festgelegten Anforderungen enthält die vorliegende internationale Norm Angaben über die Verpackung des Produktes.
Cônes d'obturation dentaires pour canaux radiculaires (ISO 6877:1995)
Donne les limites des dimensions des filetages à filets ronds pour douilles en métal, en matière plastique et en céramique avec bague support d'abat-jour.
Les dimensions des calibres correspondant sont également inclues
Dental root-canal obturating points (ISO 6877:1995)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6877:2000
01-januar-2000
Dental root-canal obturating points (ISO 6877:1995)
Dental root-canal obturating points (ISO 6877:1995)
Zahnärztliche Wurzelkanalfüllstifte (ISO 6877:1995)
Cônes d'obturation dentaires pour canaux radiculaires (ISO 6877:1995)
Ta slovenski standard je istoveten z: EN ISO 6877:1998
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 6877:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6877:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 6877:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 6877:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 6877:2000
IS0
INTERNATIONAL
6877
STANDARD
First edition
1995-06-o 1
Dental root-canal obturating points
Ches d ’obturation den takes pour canaux radiculaires
Reference number
IS0 6877:1995(E)
---------------------- Page: 5 ----------------------
SIST EN ISO 6877:2000
IS0 6877:1995(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 6877 was prepared by Technical Committee
lSO/TC 106, Dentistry, Subcommittee SC 1, Filing and restorative
materials.
Annexes A and B of this International Standard are for information only.
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication mav be reproduced
or utilized in any form or by any means electronic or mechanical, rncluding photocopying and
microfilm, without permission in wnting from the publisher.
International Organization for Standardiza tion
Case postale 56 0 W-1 211 Geneve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 6 ----------------------
SIST EN ISO 6877:2000
0 IS0 IS0 6877:1995(E)
Introduction
The sizes of the obturating points (cones) specified in this International
Standard have been aligned with the corresponding sizes for root-canal
instruments specified in IS0 3630-I [I].
Specific qualitative and quantitative requirements for freedom from
biological hazard are not included in this International Standard but it is
recommended that, in assessing possible biological or toxicological
hazards, reference should be made to lSO/TR 7405:1984[21 or any more
recent edition.
Manufacturers wishing to declare conformity with this International
Standard should refer to lSO/IEC Guide 22f3!
---------------------- Page: 7 ----------------------
SIST EN ISO 6877:2000
This page intentionally left blank
---------------------- Page: 8 ----------------------
SIST EN ISO 6877:2000
INTERNATIONAL STANDARD o IS0 IS0 6877:1995(E)
Dental root-canal obturating points
IS0 3665: 1976, Photography - lntra-oral dental radio-
1 Scope
graphic film - Specification.
This International Standard specifies the dimensions
and compositional requirements for prefabricated
metallic or polymeric-based points or cones suitable
3 Definitions
for use in the obturation of the dental root-canal, but
not for support of a coronal restoration. It also
For the purposes of this International Standard, the
specifies numerical systems and a colour coding
following definitions apply.
system for designating the sizes.
In addition to the requirements for the product itself, 3.1 point: Complete prefabricated metallic or
this International Standard also contains information
polymeric dental root-canal obturating point.
about packaging the product. Although this infor-
mation is important, it is not included as part of the
3.2 end: Broad end of the point.
requirements because no test methods are available
(see annex A).
3.3 tip: Narrow end of the point.
Dental root-canal obturating points are marketed
3.4 unit pack: Smallest pack of points distributed,
sterilized or unsterilized. This International Standard
containing one or more sizes of point.
covers the physical attributes expected of such
products as supplied. Requirements for sterility are
3.5 standardized points: Points having uniform
not included, and any claim that the product is sterile
standardized tapers throughout all the ranges of sizes
is the responsibility of the manufacturer (see clause
available.
A.2).
3.6 taper-sized points: Points whose sizes are
determined by the tip sizes and the tapers.
2 Normative references
The following standards contain provisions which,
through reference in this text, constitute provisions of
4 Requirements
this International Standard. At the time of publication,
the editions indicated were valid. All standards are
subject to revision, and parties to agreements based
4.1 Materials
on this International Standard are encouraged to
investigate the possibility of applying the most recent
4.1.1 Metal points
editions of the standards indicated below. Members
of IEC and IS0 maintain registers of currently valid
Throughout their tapered length, the points shall be
lnternational Standards.
smooth, uniform in composition without surface
pitting and free from inclusions or extraneous matter.
IS0 209-I : 1989, Wrought aluminium and aiuminium
alloys - Chemical composition and form of products
- Part I: Chemical composition. Testing shall be carried out in accordance with 6.2.
---------------------- Page: 9 ----------------------
SIST EN ISO 6877:2000
IS0 6877:1995(E) 0 IS0
4.12 Polymeric-based points Samples tested shall meet the requirements of
table 1.
Choose ten samples at random. If all ten samples
Throughout their tapered length, the points shall
pass the requirement, the product passes. If eight or
appear uniform in composition and colour, smooth,
with an untracked surface and free from inclusions fewer samples pass, the product fails. If nine samples
and extraneous matter. pass, test five additional samples. When five
additional samples are tested all five shall comply for
the product to pass.
Testing shall be carried out in accordance with 6.2.
The taper of the points shall be uniform for a
minimum of 16 mm from the tip as illustrated in
figure 1 and as shown in table 1.
4.2 Biocompatibility
A tolerance of + 0,OZ mm for metallic points,
+ 0 05 mm for polymeric points of sizes 010 to 025
See the Introduction for guidance on biocompatibility.
and 0,07 mm for polymeric points of sizes 030 to 140
is permissible.
Testing shall be carried out in accordance with 6.4.
4.3 Length
Unless otherwise stated by the manufacturer, the
Table 1 - Size designation for standardized points
overall length shall be not less than 28 mm. If some
other length is stated, the points shall be within
Dimensions in millimetres
+ - 2 mm of the stated length.
Size. / Diyww 1 Diay;ter 1 Diayfter
designation
To check this, choose ten samples at random. If all
ten samples pass the requirement, the product
0,42
010 0,lO 0,16
passes. If eight or fewer samples pass, the product
015 0,15 0,21 0,47
fails. If nine samples pass, test five additional
020 0,20 0,26 0,52
samples. When the five additional samples are tested
025 0,25 0,31 0,57
all five shall comply for the product to pass.
030 0,30 0,36 0,62
Testing shall be carried out in accordance with 6.3.
035 0,35 0,41 0,67
040 0,46 0,72
0,40
045 0,45 0,51 0,77
050 0,50 0,56 0,82
0,55 0,61 0,87
4.4 Size designation and taper 055
0,92
060 0,60 0,66
The designation is a numerical indication of the
I,02
070 0,70 0,76
I
projected tip diameter, measured in millimetres.
I,12
080 0,80 0,86
0,90 0,96 I,22
090
I,06 I,32
100 1 ,oo
I,16 I,42
110 I,10
4.4.1 Standardized points
I,52
120 I,20 I,26
I,62
130 I,30 I,36
The size designation of standardized points shall be in
accordance with the numbering system shown in I,72
140 I,40 I,46
table 1.
---------------------- Page: 10 ----------------------
SIST EN ISO 6877:2000
IS0 6877:1995(E)
0 IS0
Dimensions in millimetres
Optional flattened end
C
Overall length
C
X
e
Datum line
I
---
b’
8
I
- Projected diameter at tip
NOTES
I The diameters are expressed in hundredths of a millimetre. Table 1 gives the values of d,, d, and d3 for each size.
2 The taper is 0,02 mm per I mm, length, therefore, d, = d, + 0,32 mm.
3 In detail X, the exact shape of the tip is left to the option of the manufacturer.
Figure l- Diagrammatic representation of standardized points
measured from the tip, or throughout its complete
4.42 Taper-sized points
length if shorter than 16 mm.
The size designation of taper points shall be in
Testing shall be carried out in accordance with 6.4.
accordance with the system shown in figure 2.
NOTE 1 The first three numbers of the system represent
the projected tip diameter measured in hundredths of
millimetres. The last two numbers indicate the taper.
4.5 Brittleness
Not less than eight out of ten measurements of each
diameter of the ten samples tested shall meet the
None of the five samples tested (see 6.5) shall show
requirements of figure 2.
any sign of fracture.
The taper of the poi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.