EN ISO 1927-8:2012
(Main)Monolithic (unshaped) refractory products - Part 8: Determination of complementary properties (ISO 1927-8:2012)
Monolithic (unshaped) refractory products - Part 8: Determination of complementary properties (ISO 1927-8:2012)
ISO 1927-8:2012 specifies methods for the determination of the properties of unshaped refractory materials from test pieces prepared and stored in accordance with ISO 1927-5. The methods complement those described in ISO 1927-6.
The methods have been adapted from standards for shaped refractory products to make them applicable to dense and insulating castables, and ramming materials as defined in ISO 1927-1, before and after firing.
Ungeformte (monolithische) feuerfeste Erzeugnisse - Teil 8: Bestimmung zusätzlicher Eigenschaften (ISO 1927-8:2012)
Dieser Teil der ISO 1927 legt Verfahren zur Bestimmung der Eigenschaften von ungeformten feuerfesten Werkstoffen fest, die an nach ISO 1927 5 hergestellten und gelagerten Probekörpern ermittelt werden. Die Verfahren sind eine Ergänzung zu den in ISO 1927 6 beschriebenen.
Die Verfahren basieren auf Normen für geformte feuerfeste Erzeugnisse und wurden so abgeändert, dass sie auf die in ISO 1927 1 festgelegten dichten und wärmedämmenden Feuerbetone und Rammmassen im ungebrannten und gebrannten Zustand anwendbar sind.
Produits réfractaires monolithiques (non façonnés) - Partie 8: Détermination des caractéristiques complémentaires (ISO 1927-8:2012)
L'ISO 1927-8:2012 spécifie des méthodes pour la détermination des propriétés de matériaux réfractaires monolithiques (non façonnés) à partir d'éprouvettes préparées et conservées conformément à l'ISO 1927-5. Les méthodes complètent celles décrites dans l'ISO 1927-6.
Les méthodes ont été adaptées à partir de Normes internationales pour produits réfractaires façonnés pour les rendre applicables aux bétons denses et isolants ainsi qu'aux matériaux moulables tels que définis dans l'ISO 1927-1, avant et après cuisson.
Neoblikovani ognjevzdržni izdelki - 8. del: Ugotavljanje komplementarnih lastnosti (ISO 1927-8:2012)
Ta del standarda ISO 1927 določa metode za ugotavljanje lastnosti neoblikovanih ognjevzdržnih izdelkov iz vzorcev, pripravljenih in skladiščenih v skladu s standardom ISO 1927-5. Te metode dopolnjujejo metode iz standarda ISO 1927-6. Te metode izhajajo iz standardov za oblikovane ognjevzdržne izdelke ter so prilagojene zgoščenim in izolacijskim betonom ter mašilnim materialom, kot je opredeljeno v standardu ISO 1927-1, pred žganjem in po njem.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2013
1DGRPHãþD
SIST EN 1402-8:2004
Neoblikovani ognjevzdržni izdelki - 8. del: Ugotavljanje komplementarnih lastnosti
(ISO 1927-8:2012)
Unshaped refractory materials - Part 8: Determination of complementary properties (ISO
1927-8:2012)
Ungeformte feuerfeste Erzeugnisse - Teil 8: Bestimmung zusätzlicher Eigenschaften
(ISO 1927-8:2012)
Produits réfractaires non façonnés - Partie 8: Détermination des caractéristiques
complémentaires (ISO 1927-8:2012)
Ta slovenski standard je istoveten z: EN ISO 1927-8:2012
ICS:
81.080 Ognjevzdržni materiali Refractories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 1927-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 81.080 Supersedes EN 1402-8:2003
English Version
Monolithic (unshaped) refractory products - Part 8:
Determination of complementary properties (ISO 1927-8:2012)
Produits réfractaires monolithiques (non façonnés) - Partie Ungeformte (monolithische) feuerfeste Erzeugnisse - Teil 8:
8: Détermination des caractéristiques complémentaires Bestimmung zusätzlicher Eigenschaften (ISO 1927-8:2012)
(ISO 1927-8:2012)
This European Standard was approved by CEN on 30 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1927-8:2012: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Foreword
This document (EN ISO 1927-8:2012) has been prepared by Technical Committee ISO/TC 33 "Refractories"
in collaboration with Technical Committee CEN/TC 187 “Refractory products and materials” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1402-8:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1927-8:2012 has been approved by CEN as a EN ISO 1927-8:2012 without any modification.
INTERNATIONAL ISO
STANDARD 1927-8
First edition
2012-12-01
Monolithic (unshaped) refractory
products —
Part 8:
Determination of complementary
properties
Produits réfractaires monolithiques (non façonnés) —
Partie 8: Détermination des caractéristiques complémentaires
Reference number
ISO 1927-8:2012(E)
©
ISO 2012
ISO 1927-8:2012(E)
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 1927-8:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Determination of permeability to gases . 2
4.1 Principle . 2
4.2 Test pieces . 2
4.3 Procedure . 2
5 Determination of the resistance to thermal shock . 2
5.1 Principle . 2
5.2 Test pieces . 2
5.3 Procedure . 2
6 Determination of thermal conductivity . 3
6.1 Principle . 3
6.2 Test pieces . 3
6.3 Procedure . 3
7 Determination of sulfuric acid resistance . 3
7.1 Principle . 3
7.2 Test pieces . 3
7.3 Procedure . 3
8 Tests for products containing carbon . 3
8.1 Principle . 3
8.2 Test pieces . 4
8.3 Procedure . 4
9 Determination of the resistance to carbon monoxide . 4
10 Determination of resistance to abrasion at ambient temperature .4
11 Test report . 4
ISO 1927-8:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1927-8 was prepared by Technical Committee ISO/TC 33, Refractories.
ISO 1927 consists of the following parts, under the general title Monolithic (unshaped) refractory products:
— Part 1: Introduction and classification
— Part 2: Sampling for testing
— Part 3: Characterization as received
— Part 4: Determination of consistency of castables
— Part 5: Preparation and treatment of test pieces
— Part 6: Measurement of physical properties
— Part 7: Tests on pre-formed shapes
— Part 8: Determination of complementary properties
iv © ISO 2012 – All rights reserved
INTERNATIONAL STANDARD ISO 1927-8:2012(E)
Monolithic (unshaped) refractory products —
Part 8:
Determination of complementary properties
1 Scope
This part of ISO 1927 specifies methods for the determination of the properties of unshaped refractory
materials from test pieces prepared and stored in accordance with ISO 1927-5. The methods complement
those described in ISO 1927-6.
The methods have been adapted from standards for shaped refractory products to make them applicable
to dense and insulating castables, and ramming materials as defined in ISO 1927-1, before and after firing.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8841, Dense, shaped refractory products — Determination of permeability to gases
ISO 1927-1, Monolithic (unshaped) refractory products — Part 1: Introduction and classification
ISO 1927-2, Monolithic (unshaped) refractory products — Part 2: Sampling for testing
ISO 1927-3, Monolithic (unshaped) refractory products — Part 3: Characterization as received
ISO 1927-5, Monolithic (unshaped) refractory products — Part 5: Preparation and treatment of test pieces
ISO 1927-6, Monolithic (unshaped) refractory products — Part 6: Measurement of physical properties
ISO 8894-1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.