iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15091:2024

(Main)

Sanitary tapware - Electronic opening and closing sanitary tapware

Sanitary tapware - Electronic opening and closing sanitary tapware

The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.
The conditions of use for the supply system type are specified in Table 2:
[Table 2]
Annex B lists possible consequences of using a product outside its recommended operating range.
[Figure 1]
[Figure 2]

Sanitärarmaturen - Sanitärarmaturen mit elektronischer Öffnungs- und Schließfunktion

Dieses Dokument legt die Anforderungen an die Kennzeichnung, Identifizierung, Dichtheit, elektrische Sicherheit, Betriebssicherheit und mechanische Festigkeit von Sanitärarmaturen mit elektronisch geregelter Öffnungs- und Schließfunktion fest.
Die Einsatzbedingungen für die Wasserversorgungssysteme sind in Tabelle2 festgelegt:
[Tabelle 2]
AnhangB führt mögliche Auswirkungen für den Fall auf, dass ein Produkt außerhalb seines empfohlenen Betriebsbereiches verwendet wird.
[Bild 1]
[Bild 2]

Robinetterie sanitaire - Robinet sanitaire à ouverture et fermeture électroniques

L’objectif du présent document est de spécifier les exigences de marquage, d’identification, d’étanchéité, de sécurité électrique et de fonctionnement et de résistance mécanique pour la robinetterie sanitaire à ouverture et fermeture électroniques.
Les conditions d’utilisation relatives au type de système d’alimentation sont spécifiées dans le Tableau 2 :
[Tableau 2]
L’Annexe B indique les conséquences possibles en cas d’utilisation d’un produit en dehors du domaine de fonctionnement recommandé.
[Figure 1]
[Figure 2]

Sanitarne armature - Elektronsko odpiranje in zapiranje sanitarnih armatur

General Information

Status
Published
Publication Date
19-Mar-2024
ICS
91.140.70 - Sanitary installations
Technical Committee
CEN/TC 164 - Water supply
Drafting Committee
CEN/TC 164/WG 8 - Sanitary tapware
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Mar-2024
Due Date
02-Feb-2023
Completion Date
20-Mar-2024
Ref Project
SIST EN 15091:2024 - Sanitary tapware - Electronic opening and closing sanitary tapware

Relations

Replaces
EN 15091:2013 - Sanitary tapware - Electronic opening and closing sanitary tapware
Effective Date
18-Jan-2023

Buy Standard

prEN 15091:2022prEN 15091:2022
PreviousNext
Draft
prEN 15091:2022
English language
51 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15091:2022
01-maj-2022
Sanitarne armature - Elektronsko odpiranje in zapiranje sanitarnih armatur
Sanitary tapware - Electronic opening and closing sanitary tapware
Sanitärarmaturen - Sanitärarmaturen mit elektronischer Öffnungs- und Schließfunktion
Robinetterie sanitaire - Robinet sanitaire à ouverture et fermeture électroniques
Ta slovenski standard je istoveten z: prEN 15091
ICS:
91.140.70 Sanitarne naprave Sanitary installations
oSIST prEN 15091:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15091:2022

---------------------- Page: 2 ----------------------
oSIST prEN 15091:2022


DRAFT
EUROPEAN STANDARD
prEN 15091
NORME EUROPÉENNE

EUROPÄISCHE NORM

March 2022
ICS 91.140.70 Will supersede EN 15091:2013
English Version

Sanitary tapware - Electronic opening and closing sanitary
tapware
Robinetterie sanitaire - Robinet sanitaire à ouverture Sanitärarmaturen - Sanitärarmaturen mit
et fermeture électroniques elektronischer Öffnungs- und Schließfunktion
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 164.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15091:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15091:2022
prEN 15091:2022 (E)
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 7
2 Normative references . 9
3 Terms and definitions . 10
4 General requirements and testing . 11
4.1 General. 11
4.2 Identification . 11
4.3 Materials . 11
4.3.1 Chemical and hygienic requirements . 11
4.3.2 Exposed surface conditions . 11
4.4 Functions . 11
4.5 Backflow protection .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 200:2023(Main)
Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
SIST EN 200:2024

This document specifies:
a)   the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:
1)   a supply system of Type 1 (see Figure 1) with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar];
2)   a supply system of Type 2 (see Figure 2) with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar];
b)   the dimensional, leak tightness, pressure resistance, hydraulic performance, mechanical strength, endurance, corrosion resistance of the surface of the product, sequence of testing and acoustic characteristics with which sanitary tapware products including their components (flexible hose, pullout spray) need to comply where applicable;
c)   test methods to verify the characteristics.
The tests described in this document are type tests (laboratory tests) and not quality control or factory production control (FPC) tests carried out during manufacture.
This document is applicable to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for personal hygiene (cloakrooms, bathrooms etc.) and for food preparation (kitchens), i.e. for use with baths, basins, bidets, showers and sinks.
This document applies to sanitary draw-off taps of nominal size 3/8”, 1/2", 3/4" and 1” (PN 10).
The conditions of use and classifications are given in Table 1.
Table 1 - Conditions of use
[ table not reproduced here ]
[ figure not reporduced here ]
Figure 1- Supply system of Type 1 with a pressure range of (0,05 to 1,0) MPa [(0,5 to 10) bar]
[ figure not reporduced here ]
Figure 2 - Supply system of Type 2 with a pressure range of (0,01 to 1,0) MPa [(0,1 to 10) bar]
NOTE   Components which are part or can be delivered with sanitary tapware products are listed in Annex C.
Final materials included in the product are not covered by this document.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 246:2021(Main)
Sanitary tapware - General specifications for aerators
SIST EN 246:2022

This document specifies:
- the dimensional, mechanical, hydraulic and acoustic characteristics with which sanitary tapware aerators (with and without flow regulation) should comply;
- the procedures for testing these characteristics.
This document is applicable to:
- Sanitary tapware aerators intended to be mounted on tapware used with sanitary appliances in toilets, bathrooms and kitchens (e.g. single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
- Sanitary tapware aerators used under the following pressure and temperature conditions (see Table 1).
[Table 1: Conditions for the use of aerators]
NOTE 1   Sanitary tapware aerators can only be connected downstream of the obturator of the sanitary tapware product.
NOTE 2   For the purposes of brevity, sanitary tapware aerators will be detailed only as aerators in the rest of this document.
NOTE 3   The tests described in this document are type tests (laboratory tests) and not quality control tests carried out during manufacture.
NOTE 4   Aerator swivels are to be tested in combination with a specific aerator only and are therefore considered to be sanitary tapware accessories. (Testing of the stand-alone swivels is therefore not covered by the scope of this document. Where swivels are used they are considered to be part of the tapware constructions, e.g. for bidet taps).

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1287:2017(Main)
Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification
SIST EN 1287:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature - 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilet and cloakrooms) and bathrooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve, controlling a shower, bath, basin and/or, bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 816:2017(Main)
Sanitary tapware - Automatic shut-off valves PN 10
SIST EN 816:2017

This European Standard is applicable to single and mixer taps with automatic shut-off for use with sanitary appliances installed in washrooms.
It does not apply to urinal or WC flushing valves or valves which open automatically.
The purpose of this standard is to specify the marking, identification, chemical/hygiene, dimensional, leaktightness, pressure resistance, hydraulic, mechanical endurance, and acoustical characteristics of automatic shut-off tapware.
The tests described in all the standard are type tests (laboratory tests) and not quality control tests carried out during manufacture
The following conditions of pressure and temperature apply:
Table 1 - Conditions for the use of self closing tapware
(The pressures given are flow pressures)

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1111:2017(Main)
Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
SIST EN 1111:2017

This European Standard specifies general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available. When these devices are used to provide anti-scald protection for children, elderly and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature approximately 38 °C) as children are at risk to scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
It applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g. toilets and cloakrooms) and bath rooms operating under the conditions specified in Table 1.
This standard allows TMVs to supply a single outlet or a small number of outlets in a "domestic" application (e.g. one valve controlling a shower, bath, basin and/or bidet), excluding valves specifically designed for supplying a large number of outlets (i.e. for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Table 1 - Conditions of use

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1113:2015(Main)
Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
SIST EN 1113:2015

This European Standard specifies:
-   the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply;
-   the procedures for testing these characteristics.
This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers.
This European Standard applies to shower hoses connected downstream of the obturator of the tapware.
Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard.
Details of pressures and temperatures are given in Table 1.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16146:2012+A1:2014(Main)
Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
SIST EN 16146:2013+A1:2015

This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard.
This European Standard specifies:
-   the dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets shall comply;
-   the procedures for testing these characteristics.
Details of pressures and temperatures are given in Table 1.
(...)

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16145:2012(Main)
Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification
SIST EN 16145:2013

This European Standard specifies:
-   the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply;
-   the procedures for testing these characteristics.
It applies to extractable outlets made from any material which is intended for equipping and supplementing sanitary tapware for sinks and wash-basins used for culinary or ablutionary purposes. Such extractable outlets shall only be connected downstream of the obturator of the tapware.
Extractable outlets with total closing device fitted after the obturator of the tapware are not covered by this standard. Such products will be tested in accordance with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see [1], [2], [3], [5] and [6]).
The conditions of use and classification are specified in Table 1.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 817:2008(Main)
Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications
SIST EN 817:2009

This European Standard specifies:
   the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics with which mechanical mixing valves need to comply;
   test methods to verify the characteristics;
   the tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.
This European Standard applies to PN 10 mechanical mixing valves for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms, etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks.
The conditions of use and classifications are given in Table 1.
Table 1   - Conditions of use/classifications

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14124:2004(Main)
Inlet valves for flushing cisterns with internal overflow
SIST EN 14124:2004

The purpose of this document is to specify:
- the dimensional, hygiene, tightness, pressure performance, hydraulic, acoustic, mechanical and physico chemical characteristics which inlet valves for flushing cisterns shall comply with;
- the test methods for  testing these characteristics;
- marking and presentation.
This document applies exclusively to the valve itself and it does not prejudge compliance with health regulations as the inlet valve is being fitted into the cistern.
This document does not cover valves intended to equip flushing cisterns with external overflow.
This document applies to valves such as float valves limit operating at pressures up to NP 10 (whose operating range is from 0,05 MPa to 1 MPa - 0,5 bar to 10 bar) designed to supply cold water to flushing cisterns for use with WC pans, that are permanently connected to a potable water supply system.
The working range can be extended downwards (< 0,05 MPa - 0,5 bar) down to 0,01 MPa (0,1 bar), in which case the manufacturer's instructions shall indicate this possibility as well as the recommended working range.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day