iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13852-1:2004

(Main)

Cranes - Offshore cranes - Part 1: General - purpose offshore cranes

Cranes - Offshore cranes - Part 1: General - purpose offshore cranes

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures.
This standard applies to cranes manufactured after the date of issue of this standard.
This European Standard does not cover:
a) Fabrication, assembly, dismantling or changing the configuration of the crane;
b) Lifting accessories, i.e. any item between the hook and the load;
c) Sub-sea lifting operations;
d) Design temperature below -20 °C;
e) Operations at an ambient temperature above 40 °C;
f) Lifting operations involving more than one crane;
g) Transportation of the crane;
h) Loads due to earthquake;
i) Cranes on seagoing vessels, excluded from the scope of the Machinery Directive.
The significant hazards covered by this European Standard are identified in clause 4.
This standard includes requirements for the lifting of personnel.
Where National Authorities permit the use of a general-purpose offshore crane for the lifting of personnel, the crane would at least need to fulfil the requirements of this standard.

Krane - Offshore-Krane - Teil 1: Offshore-Krane für allgemeine Verwendung

Diese Europäische Norm spezifiziert die Anforderungen an Offshore-Krane für allgemeine Verwendung einschließlich ihrer Tragsäulen und Fundamente.
Diese Norm ist auf Krane anzuwenden, die nach dem Datum der Herausgabe dieser Norm hergestellt werden.
Diese Europäische Norm gilt nicht für:
a)   Herstellung, Montage, Demontage oder Änderung des Kranrüstzustands;
b)   Lastaufnahmemittel, d. h. alle Teile zwischen dem Haken und der Last ;
c)   Unterwasser-Hebearbeiten;
d)   Entwurfstemperaturen unter - 20 °C;
e)   Arbeiten bei Umgebungstemperaturen über 40 °C;
f)   Hebearbeiten mit mehr als einem Kran;
g)   Transport der Krane;
h)   Beanspruchungen durch Erdbeben;
i)   Krane auf Seeschiffen, die nicht den Bestimmungen der Maschinenrichtlinie unterliegen.
Die durch diese Europäische Norm erfassten wesentlichen Gefährdungen sind in Abschnitt 4 aufgeführt.
Diese Norm schließt Bestimmungen für den Transport von Personal ein.
Wenn nationale Behörden den Einsatz eines Offshore-Kranes für allgemeine Verwendung für den Transport von Personal erlauben, muss der Kran mindestens die Anforderungen dieser Norm erfüllen.

Appareils de levage à charge suspendue - Grues offshore - Partie 1 : Grues offshore pour usage général

La présente Norme européenne spécifie les exigences relatives aux grues offshore d'usage général y compris leurs socles et structures.
Cette norme s'applique aux appareils de levage à charge suspendue construits après sa date de publication.
La présente Norme européenne ne couvre pas :
a)   la fabrication, le montage, le démontage ou la modification de configuration de l'appareil de levage à charge suspendue ;
b)   les accessoires de levage, c'est à dire tout élément entre le crochet et la charge ;
c)   les opérations de levage en milieu sous-marin ;
d)   les températures de calcul inférieure à - 20 °C ;
e)   les opérations effectuées température ambiante supérieure à 40 °C ;
f)   les opérations impliquant plus d'une grue ;
g)   le transport de la grue ;
h)   les charges dues au séisme ;
i)   les grues sur navires en mer, exclues du domaine de la Directive machine.
Les phénomènes dangereux significatifs couverts dans la présente Norme européenne sont identifiés à l'Article 4.
La présente Norme européenne comprend les prescriptions relatives au levage des personnes.
Lorsque les autorités nationales autorisent l'utilisation de grues offshore d'usage général pour le levage des personnes, il convient que la grue satisfasse au moins les exigences de la présente norme.

Dvigala - Dvigala na plavajočih objektih - 1. del: Dvigala na plavajočih objektih za splošne namene

General Information

Status
Withdrawn
Publication Date
25-May-2004
Withdrawal Date
24-Sep-2013
ICS
47.020.40 - Lifting and cargo handling equipment
53.020.20 - Cranes
Technical Committee
CEN/TC 147 - Cranes - Safety
Drafting Committee
CEN/TC 147 - Cranes - Safety
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
25-Sep-2013
Completion Date
25-Sep-2013
Directive
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
SIST EN 13852-1:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes

Relations

Replaced By
EN 13852-1:2013 - Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
Effective Date
22-May-2010
Corrected By
EN 13852-1:2004/AC:2007 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
Effective Date
08-Jun-2022
Corrected By
EN 13852-1:2004/AC:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
Effective Date
08-Jun-2022
Child
EN 13852-2:2004 - Cranes - Offshore cranes - Part 2: Floating cranes
Effective Date
22-Dec-2008

Buy Standard

EN 13852-1:2004EN 13852-1:2004
PreviousNext
Standard
EN 13852-1:2004
English language
81 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Krane - Offshore-Krane - Teil 1: Offshore-Krane für allgemeine VerwendungAppareils de levage a charge suspendue - Grues offshore - Partie 1 : Grues offshore pour usage généralCranes - Offshore cranes - Part 1: General - purpose offshore cranes53.020.20DvigalaCranes47.020.40Dvigalna oprema in oprema za pretovorLifting and cargo handling equipmentICS:Ta slovenski standard je istoveten z:EN 13852-1:2004SIST EN 13852-1:2004en01-september-2004SIST EN 13852-1:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13852-1May 2004ICS 47.020.01; 53.020.20English versionCranes - Offshore cranes - Part 1: General - purpose offshorecranesAppareils de levage - Appareils de levage offshore - Partie1: Appareils de levage offshore pour usage généralKrane - Offshore Krane - Teil 1: Offshore-Krane fürallgemeine VerwendungThis European Standard was approved by CEN on 24 March 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13852-1:2004: ESIST EN 13852-1:2004

Selection of a suitable set of crane standards for a given application.41 Annex B (normative)
Determination of factors.42 B.1 Calculation of the dynamic coefficient ΦΦΦΦn by the simplified method.42 B.2 Calculation of dynamic coefficient ΦΦΦΦn by motion response analysis.43 B.3 Out of plane influences.44 B.3.1 General.44 B.3.2 Offlead load.44 B.3.3 Sidelead load.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
SIST EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   Supporting pedestal and structures such as columns and boom rests, are covered by this document to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all of the following characteristics:
-   maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;
-   limitation for off-board lifting operation up to Hs = 2,0 m and wind speed 15 m/s (3 s gust);
-   maximum number of working cycles class U1 (C ≤ 3,15 × 104) according to EN 13001-1.
This document provides requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion compensated cranes.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-1:2013(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
SIST EN 13852-1:2013

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures.
The standard is applicable to general-purpose offshore cranes covered by the scope of this European Standard which are manufactured after the date of its publication as EN.
This European Standard is not applicable to general-purpose offshore cranes which are manufactured before the date of its publication as an EN.
This European Standard does not cover use of - or hazards relating to the following:
a)   fabrication, transportation, assembly, dismantling, disabling, scrapping or changing the configuration of the crane;
b)   lifting accessories, i.e. any item between the hook and the load;
c)   minimum design temperature below −20 °C;
d)   operations at an ambient temperature above 45 °C;
NOTE:   For equipment designed for operation in explosive atmospheres, the normal ambient temperature range is −20 °C to +40 °C, unless otherwise specified and marked. See Annex O and relevant standards indicated for complete information.
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions;
g)   hand powered cranes and other cranes with a rated capacity less than 2 t or outreach less than 8 m;
h)   emergency rescue operations; (except training)
i)   subsea lifting operations.
The significant hazards covered by this European standard are identified in Clause 4.
This European Standard includes requirements for the lifting of personnel by a general-purpose offshore crane.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2009

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2021

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
SIST EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   Supporting pedestal and structures such as columns and boom rests, are covered by this document to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all of the following characteristics:
-   maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;
-   limitation for off-board lifting operation up to Hs = 2,0 m and wind speed 15 m/s (3 s gust);
-   maximum number of working cycles class U1 (C ≤ 3,15 × 104) according to EN 13001-1.
This document provides requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion compensated cranes.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-1:2013(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
SIST EN 13852-1:2013

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures.
The standard is applicable to general-purpose offshore cranes covered by the scope of this European Standard which are manufactured after the date of its publication as EN.
This European Standard is not applicable to general-purpose offshore cranes which are manufactured before the date of its publication as an EN.
This European Standard does not cover use of - or hazards relating to the following:
a)   fabrication, transportation, assembly, dismantling, disabling, scrapping or changing the configuration of the crane;
b)   lifting accessories, i.e. any item between the hook and the load;
c)   minimum design temperature below −20 °C;
d)   operations at an ambient temperature above 45 °C;
NOTE:   For equipment designed for operation in explosive atmospheres, the normal ambient temperature range is −20 °C to +40 °C, unless otherwise specified and marked. See Annex O and relevant standards indicated for complete information.
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions;
g)   hand powered cranes and other cranes with a rated capacity less than 2 t or outreach less than 8 m;
h)   emergency rescue operations; (except training)
i)   subsea lifting operations.
The significant hazards covered by this European standard are identified in Clause 4.
This European Standard includes requirements for the lifting of personnel by a general-purpose offshore crane.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2009

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13852-1(Main)
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
oSIST prEN 13852-1:2021

This document applies to general purpose offshore cranes including their supporting pedestals and structures.
This document is applicable to general purpose offshore cranes, whose structures are made of steel.
This document provides requirements for all significant hazards, hazardous situations and events relevant to general purpose offshore cranes, for lifting of goods and lifting of persons, when used as intended and under the conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to general purpose offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below - 20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7 ;
f)   floating cranes (covered by EN13852-2), light offshore cranes (covered by FprEN13852-3) and 2D/3D motion compensated cranes;
g)   subsea lifting operations;
h)   lifting operations involving more than one crane;
i)   emergency rescue operations (except training).

  • Draft
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 16931-8:2024(Main)
Electronic invoicing - Part 8: Semantic data model of the elements of an e-receipt or a simplified electronic invoice
kSIST FprEN 16931-8:2024

This document establishes a semantic data model of an e-receipt or a simplified electronic invoice.
NOTE   In the remainder of this document, when “e-receipt” is mentioned, “simplified invoice” is also meant.
The semantic model includes essential information elements that an electronic receipt needs to ensure legal (including fiscal) compliance and to enable interoperability for cross-border, cross sector and domestic trade. The semantic model can be used by organizations in the private and the public sector for documenting by issuing a receipt for the purchase of services and /or goods. It can also be used for documenting a purchase between private sector enterprises. In addition, it has been designed for the use of consumers.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-5:2024(Main)
Paints and varnishes - Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2024)
kSIST FprEN ISO 19403-5:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids by optical methods. The method can be applied for the characterization of liquid coating materials.
If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day