prEN ISO 1089
(Main)Resistance welding equipment - Electrode taper fits for spot welding equipment - Dimensions (ISO/DIS 1089:2021)
Resistance welding equipment - Electrode taper fits for spot welding equipment - Dimensions (ISO/DIS 1089:2021)
Refers to taper dimensions and tolerances for electrode caps, electrode adaptors, electrode holders and similar parts, where the electrode force Fmax, given for diameter d1 in tables 1, 2 and 3 is not exceeded. Establishes dimensions, designation and marking. Cancels and replaces ISO Recommendation R 1089-1969, of which it constitutes a technical revision.
Widerstandsschweißeinrichtungen - Elektrodensitze für Punktschweißeinrichtungen - Maße (ISO/DIS 1089:2021)
Dieses Dokument legt Kegelmaße und zulässige Abweichungen von Kegelsitzen für Punktschweiß-Elektrodenkappen, -Schäften, -Haltern und ähnliche Teile fest, wobei die in den Tabelle 1, Tabelle 2 und Tabelle 3 für den Durchmesser d1 festgelegte Elektrodenkraft Fmax nicht überschritten wird.
Matériel de soudage par résistance - Emmanchements coniques d'électrodes pour machines à souder par points - Dimensions (ISO/DIS 1089:2021)
La présente Norme internationale fixe les dimensions et tolérances des emmanchements coniques d'électrodes pour l'embout amovible de pointes d'électrodes pour soudage par points, des corps de pointes d'électrodes, porte-électrodes et éléments similaires, où la force d'électrode, Fmax,donnée pour le diamètre d1, n'excède par les valeurs données dans les tableaux 1, 2 et 3.
Oprema za uporovno varjenje - Nastavki elektrod pri opremi za točkovno varjenje - Mere (ISO/DIS 1089:2021)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 1089:2021
01-marec-2021
Uporovno varjenje - Nasedi elektrod pri napravah za elektrouporovno točkovno
varjenje - Mere (ISO/DIS 1089:2021)
Resistance welding equipment - Electrode taper fits for spot welding equipment -
Dimensions (ISO/DIS 1089:2021)
Widerstandsschweißeinrichtungen - Elektrodensitze für Punktschweißeinrichtungen -
Maße (ISO/DIS 1089:2021)
Emmanchements coniques d'électrodes pour machines à souder par points -
Dimensions (ISO/DIS 1089:2021)
Ta slovenski standard je istoveten z: prEN ISO 1089
ICS:
25.160.30 Varilna oprema Welding equipment
oSIST prEN ISO 1089:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 1089:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 1089:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 1089
ISO/TC 44/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2021-02-11 2021-05-06
Resistance welding equipment — Electrode taper fits for
spot welding equipment – Dimensions
ICS: 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 1089:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 1089:2021
ISO/DIS 1089:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 1089:2021
ISO/DIS 1089:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
5 Designation . 1
6 Marking . 2
© ISO 2021 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 1089:2021
ISO/DIS 1089:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is inform
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.