CEN/TS 16165:2016

Determination of slip resistance of pedestrian surfaces - Methods of evaluation

This Technical Specification specifies test methods for the determination of the slip resistance of surfaces in the most commonly encountered situations in which pedestrians walk.
This Technical Specification does not cover sports surfaces and road surfaces for vehicles (skid resistance).

Bestimmung des Gleitwiderstandes von Fußgängerbereichen - Ermittlungsverfahren

Détermination de la résistance à la glissance des surfaces piétonnières - Méthodes d’évaluation

La présente Spécification technique spécifie les méthodes d’essai pour la détermination de la résistance à la glissance des surfaces sur lesquelles des piétons marchent dans les situations les plus courantes.
La présente Spécification technique ne couvre pas les surfaces destinées à un usage sportif ni les revêtements de route pour véhicules (résistance au dérapage).

Ugotavljanje odpornosti talnih površin proti zdrsu - Metoda vrednotenja

Ta tehnična specifikacija določa preskusne metode za ugotavljanje odpornosti površin proti zdrsu v najobičajnejših okoliščinah pri hoji peščev. Ta tehnična specifikacija ne zajema športnih in cestnih površin za vozila (torna sposobnost).

General Information

• Status: Withdrawn
• Publication Date: 30-Aug-2016
• Withdrawal Date: 26-Oct-2021
• ICS: 17.040.20 - Properties of surfaces
• ICS: 93.080.10 - Road construction
• Technical Committee: CEN/TC 339 - Slip resistance of pedestrian surfaces - Methods of evaluation
• Drafting Committee: CEN/TC 339 - Slip resistance of pedestrian surfaces - Methods of evaluation
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 27-Oct-2021
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/127 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on construction adhesives
• Ref Project: SIST-TS CEN/TS 16165:2016 - Determination of slip resistance of pedestrian surfaces - Methods of evaluation

Relations

• Replaces: CEN/TS 16165:2012 - Determination of slip resistance of pedestrian surfaces - Methods of evaluation
• Effective Date: 16-Nov-2014
• Replaced By: EN 16165:2021 - Determination of slip resistance of pedestrian surfaces - Methods of evaluation
• Effective Date: 03-Nov-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST-TS CEN/TS 16165:2014
Ugotavljanje odpornosti talnih površin proti zdrsu - Metoda vrednotenja
Determination of slip resistance of pedestrian surfaces - Methods of evaluation
Bestimmung des Gleitwiderstandes von Fußgängerbereichen - Ermittlungsverfahren
Détermination de la résistance à la glissance des surfaces piétonnières - Méthode
d'évaluation
Ta slovenski standard je istoveten z: CEN/TS 16165:2016
ICS:
17.040.20 Lastnosti površin Properties of surfaces
93.080.10 Gradnja cest Road construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN/TS 16165
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
August 2016
TECHNISCHE SPEZIFIKATION
ICS 17.040.20; 93.080.10 Supersedes CEN/TS 16165:2012
English Version
Determination of slip resistance of pedestrian surfaces -
Methods of evaluation
Détermination de la résistance à la glissance des Bestimmung des Gleitwiderstandes von
surfaces piétonnières - Méthodes d'évaluation Fußgängerbereichen - Ermittlungsverfahren
This Technical Specification (CEN/TS) was approved by CEN on 12 June 2016 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16165:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Test methods . 9
Annex A (normative) Barefoot Ramp Test . 10
A.1 Principle . 10
A.2 Test equipment . 10
A.2.1 Test apparatus. 10
A.2.2 Test surface . 11
A.2.3 Contaminant . 11
A.3 Calibration . 12
A.3.1 General . 12
A.3.2 Validation of the test person . 12
A.4 Test procedure . 13
A.5 Evaluation . 14
A.6 Precision . 15
A.7 Test report . 15
Annex B (normative) Shod Ramp Test . 16
B.1 Principle . 16
B.2 Test equipment . 16
B.2.1 Test apparatus with safety devices . 16
B.2.2 Test surface . 17
B.2.3 Contaminant . 17
B.2.4 Test footwear . 18
B.3 Calibration . 18
B.3.1 General . 18
B.3.2 Validation of the test person . 18
B.4 Test procedure . 19
B.5 Evaluation . 20
B.6 Precision . 21
B.7 Test report . 21
Annex C (normative) Pendulum friction test . 22
C.1 Principle . 22
C.2 Apparatus . 22
C.2.1 Pendulum friction tester . 22
C.2.2 Additional items required for testing . 27
C.3 Preparation . 27
C.3.1 General . 27
C.3.2 Preparation of the slider . 29
C.3.3 Small units . 31
C.3.4 Flatness of the surface . 31
C.4 Verification . 31
C.5 Conducting the test . 32
C.5.1 Procedure . 32
C.5.2 Checking for error . 33
C.5.3 Calculating the pendulum test value (PTV) . 33
C.6 Pendulum measurements on site, additional information . 33
C.7 Precision . 35
C.8 Test report . 35
C.9 Pendulum scale dimensions . 36
C.10 Calibration procedure for the pendulum friction tester . 37
C.10.1 General . 37
C.10.2 Pre-calibration verification . 37
C.10.3 Detailed condition check . 38
C.10.4 Checking/setting the centre of gravity of the pendulum arm and slider assembly . 38
C.10.5 Checking/setting the effective spring tension . 40
C.10.6 Checking/setting the slider force/deflection characteristics . 42
C.10.7 Checking/setting the levelness of the frame . 43
C.10.8 Final calibration . 44
C.10.9 Calibration report and marking (external calibration). 44
Annex D (normative) Tribometer test . 46
D.1 Principle . 46
D.2 Apparatus and test equipment . 46
D.2.1 Apparatus . 46
D.3 Test equipment. 47
D.4 Verification and checking . 48
D.4.1 Verification of the load cell . 48
D.4.2 Checking of the slider material . 49
D.5 Sampling and preparation of the test sample for laboratory tests . 49
D.6 Preparation of the test surface for on-site tests. 50
D.7 Preparation of the sliders . 51
D.8 Procedure.
...