EN ISO 18473-4:2023
(Main)Functional pigments and extenders for special applications - Part 4: Nanoscale titanium dioxide for photocatalytic application (ISO 18473-4:2022)
Functional pigments and extenders for special applications - Part 4: Nanoscale titanium dioxide for photocatalytic application (ISO 18473-4:2022)
This document specifies requirements and corresponding test methods for nanoscale titanium dioxide (TiO2) in either powder or suspension form for photocatalytic application.
This document is applicable to modified nanoscale titanium dioxide for photocatalytic application.
NOTE Such modification can be surface treatment, coating, doping and combination thereof.
Funktionelle Pigmente und Füllstoffe für besondere Anwendungen - Teil 4: Titandioxid im Nanomaßstab für photokatalytische Zwecke (ISO 18473-4:2022)
Pigments et matières de charges fonctionnels pour applications spéciales - Partie 4: Dioxyde de titane à l'échelle nanométrique pour des applications photocatalytiques (ISO 18473-4:2022)
Funkcionalni pigmenti in polnila za posebno uporabo - 4. del: Nano titanov dioksid za fotokatalitsko uporabo (ISO 18473-4:2022)
Za dokument določa zahteve in ustrezne preskusne metode za nano titanov dioksid (TiO2) v prahu ali suspenziji za fotokatalitsko uporabo.
Ta dokument se uporablja za modificiran nano titanov dioksid za fotokatalitsko uporabo. To je lahko površinska obdelava, premazovanje, dopiranje ali kombinacija le-teh.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2023
Funkcionalni pigmenti in polnila za posebno uporabo - 4. del: Nano titanov dioksid
za fotokatalitsko uporabo (ISO 18473-4:2022)
Functional pigments and extenders for special applications - Part 4: Nanoscale titanium
dioxide for photocatalytic application (ISO 18473-4:2022)
Funktionelle Pigmente und Füllstoffe für besondere Anwendungen - Teil 4: Titandioxid im
Nanomaßstab für photokatalytische Zwecke (ISO 18473-4:2022)
Pigments et matières de charges fonctionnels pour applications spéciales - Partie 4:
Dioxyde de titane à l'échelle nanométrique pour des applications photocatalytiques (ISO
18473-4:2022)
Ta slovenski standard je istoveten z: EN ISO 18473-4:2023
ICS:
87.060.10 Pigmenti in polnila Pigments and extenders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 18473-4
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2023
EUROPÄISCHE NORM
ICS 87.060.10
English Version
Functional pigments and extenders for special applications
- Part 4: Nanoscale titanium dioxide for photocatalytic
application (ISO 18473-4:2022)
Pigments et matières de charges fonctionnels pour Funktionelle Pigmente und Füllstoffe für besondere
applications spéciales - Partie 4: Dioxyde de titane à Anwendungen - Teil 4: Titandioxid im Nanomaßstab
l'échelle nanométrique pour des applications für photokatalytische Zwecke (ISO 18473-4:2022)
photocatalytiques (ISO 18473-4:2022)
This European Standard was approved by CEN on 16 July 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18473-4:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 18473-4:2022 has been prepared by Technical Committee ISO/TC 256 "Pigments,
dyestuffs and extenders” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 18473-4:2023 by Technical Committee CEN/TC 298 “Pigments and extenders” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2024, and conflicting national standards shall
be withdrawn at the latest by January 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 18473-4:2022 has been approved by CEN as EN ISO 18473-4:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 18473-4
First edition
2022-02
Functional pigments and extenders for
special applications —
Part 4:
Nanoscale titanium dioxide for
photocatalytic application
Reference number
ISO 18473-4:2022(E)
ISO 18473-4:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 18473-4:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification and designation . 2
4.1 Classification . 2
4.2 Designation . 2
5 Requirements and test methods . 3
5.1 Appearance . 3
5.2 Technical requirements . 3
6 Sampling . 4
7 Marking and labelling . 4
8 Test report . 4
Bibliography . 5
iii
ISO 18473-4:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 256, Pigments, dyestuffs and extenders.
A list of all parts in the ISO 18473 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html
iv
ISO 18473-4:2022(E)
Introduction
Metal nanoparticles are promising materials as the heterogeneous catalyst in a variety of organic
transformations. Their catalytic properties are functions of their size and crystal lattice parameters,
and they show amazing levels of performance in terms of selectivity, activity and improved yield of
products. In particular, nanoscale titanium dioxide (TiO ) particles exhibited many special properties
because the band gap of the nanoparticles increased with the decrease in size. The use of TiO
nanoparticles has received considerable attention in green synthetic organic chemistry, decomposition
and removal of air and water contaminants, deodorization, and antibacterial, antifungal, self-cleaning
and antifogging actions.
v
INTERNATIONAL STANDARD ISO 18473-4:2022(E)
Functional pigments and extenders for special
applications —
Part 4:
Nanoscale titanium dioxide for photocatalytic application
1 Scope
This document specifies requirements and corresponding test methods for nanoscale titanium dioxide
(TiO ) in either powder or suspension form for photocatalytic application.
This document is applicable to modified nanoscale titanium dioxide for photocatalytic application.
NOTE Such modification can be surface treatment, coating, doping and combination thereof.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 591-1:2000, Titanium dioxide pigments for paints — Part 1: Specifications and methods of test
ISO 787-2, General methods of test for pigments and extenders — Part 2: Determination of matter volatile
at 105 °C
ISO 787-9, General methods of test for pigments and extenders — Part 9: Determination of pH value of an
aqueous suspension
ISO 787-11, General methods of test for pigments and extenders — Part 11: Determination of tamped
volume and apparent density after tamping
ISO 787-18, General methods of test for pigments and extenders — Part 18: Determination of residue on
sieve — Mechanical flushing procedure
ISO 3262-1, Extenders — Specifications and methods of test — Part 1: Introduction and general test
methods
ISO 6227, Chemical products for industrial use — General method for determination of chloride ions —
Potentiometric method
ISO 9277, Determination of th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.