EN 754-2:2008

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties

This document specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy cold drawn rod/bar and tube.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 2: Mechanische Eigenschaften

Dieses Dokument legt die Grenzwerte für die mechanischen Eigenschaften von gezogenen Stangen und
Rohren aus Aluminium und Aluminiumlegierungen fest.
Die technischen Lieferbedingungen, einschließlich Erzeugnis- und Prüfanforderungen, sind in EN 754-1
festgelegt. Die Bezeichnungen der Werkstoffzustände sind in EN 515 definiert. In EN 573-3 sind die Grenzen
der chemischen Zusammensetzung für diese Werkstoffe angegeben.

Aluminium et alliages d'aluminium - Barres et tubes étirés - Partie 2: Caractéristiques mécaniques

Le présent document spécifie les limites des caractéristiques mécaniques provenant de l’essai de traction applicables aux barres et tubes étirés en aluminium et alliages d’aluminium.
Les conditions techniques de contrôle et de livraison, y compris les produits et les exigences d’essai, sont spécifiées dans l’EN 754-1. La désignation des états métallurgiques sont définis dans l’EN 515. Les limites de composition chimique de ces matériaux sont données dans l’EN 573-3.

Aluminij in aluminijeve zlitine - Hladno vlečene palice/drogovi in cevi - 2. del: Mehanske lastnosti

General Information

• Status: Withdrawn
• Publication Date: 18-Mar-2008
• Withdrawal Date: 01-Oct-2013
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 5 - Extruded and drawn products
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 02-Oct-2013
• Completion Date: 02-Oct-2013
• Ref Project: SIST EN 754-2:2008 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties

Relations

• Replaces: EN 754-2:1997 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
• Effective Date: 22-Dec-2008
• Replaced By: EN 754-2:2013 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
• Effective Date: 09-Oct-2013

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical propertiesAluminium et alliage d'aluminium - Barre et tubes étirés - Partie 2: Caractéristiques mécaniquesAluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 2: Mechanische EigenschaftenTa slovenski standard je istoveten z:EN 754-2:2008SIST EN 754-2:2008en,de77.150.10ICS:SIST EN 754-2:19981DGRPHãþDSLOVENSKI
STANDARDSIST EN 754-2:200801-maj-2008

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 754-2March 2008ICS 77.150.10Supersedes EN 754-2:1997
English VersionAluminium and aluminium alloys - Cold drawn rod/bar and tube -Part 2: Mechanical propertiesAluminium et alliages d'aluminium - Barres et tubes étirés -Partie 2: Caractéristiques mécaniquesAluminium und Aluminiumlegierungen - Gezogene Stangenund Rohre - Teil 2: Mechanische EigenschaftenThis European Standard was approved by CEN on 10 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 754-2:2008: E

List of tempers used in Tables 1 to 35.42 Bibliography.44

2 Normative references The following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (including any amendments) applies. EN 754-1:2008, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 1: Technical conditions for inspection and delivery EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature 3 Mechanical property limits 3.1 General The mechanical properties shall be in conformity with those specified in Tables 1 to 35 or those agreed upon between supplier and purchaser and stated in the order document. For all alloys the condition F (as fabricated) can be used, but without guaranteed mechanical properties. Tables 1 to 35 contain limits of mechanical property values obtained by tensile testing according to EN 10002-1 after sampling and test piece preparation according to EN 754-1. NOTE The mechanical properties refer to test pieces taken in the longitudinal direction. Mechanical properties of test pieces taken in other directions can differ from those for the longitudinal direction quoted in this standard. Brinell hardness values given in Tables 1 to 35 expressed as HBW values are for information only. 3.2 Elongation If not otherwise agreed, the A value shall be used.
The A value for elongation is the % elongation measured over a gauge length of 065,5S (where S0 is the initial cross-sectional area of the test-piece), and expressed in percent. For certain products the supplier may choose (if not otherwise specified in the order documents) to use the elongation based on A50mm. Consequently values for the A50mm are included in the following tables.
The A50mm value is the elongation measured over a gauge length of 50 mm and expressed in percent. Test pieces and their location in the specimen are given in EN 754-1.

Page Table 1
: Aluminium EN AW-1050A [Al 99,5]7 Table 2
: Aluminium EN AW-1200 [AI 99,0] 8 Table 3
: Alloy EN AW-2007 [Al Cu4PbMgMn] 9 Table 4
: Alloy EN AW-2011 [AI Cu6BiPb] 10 Table 5
: Alloy EN AW-2011A [AI Cu6BiPb(A)] 11 Table 6
: Alloy EN AW-2014 [AI Cu4SiMg] 12 Table 7
: Alloy EN AW-2014A [AI Cu4SiMg(A)] 13 Table 8
: Alloy EN AW-2017A [AI Cu4MgSi(A)] 14 Table 9
: Alloy EN AW-2024 [AI Cu4Mg1] 15 Table 10 : Alloy EN AW-2030 [AI Cu4PbMg] 16 Table 11 : Alloy EN AW-3003 [AI Mn1Cu]17 Table 12 : Alloy EN AW-3103 [AI Mn1] 18 Table 13 : Alloy EN AW-5005 [AI Mg1(B)] 19 Table 14 : Alloy EN AW-5005A [AI Mg1(C)] 20 Table 15 : Alloy EN AW-5019 [AI Mg5] 21 Table 16 : Alloy EN AW-5049 [Al Mg2Mn0,8] 22 Table 17 : Alloy EN AW-5251 [AI Mg2Mn0,3] 23 Table 18 : Alloy EN AW-5052 [AI Mg2,5] 24 Table 19 : Alloy EN AW-5154A [AI Mg3,5(A)] 25 Table 20 : Alloy EN AW-5754 [AI Mg3] 26 Table 21 : Alloy EN AW-5083 [AI Mg4,5Mn0,7] 27 Table 22 : Alloy EN AW-5086 [AI Mg4] 28 Table 23 : Alloy EN AW-6012 [AI MgSiPb]29 Table 24 : Alloy EN AW-6060 [AI MgSi] 30 Table 25 : Alloy EN AW-6061 [AI Mg1SiCu] 31 Table 26 : Alloy EN AW-6262 [AI Mg1SiPb] 32 Table 27 : Alloy EN AW-6262A [AI Mg1SiSn] 33 Table 28 : Alloy EN AW-6063 [AI Mg0,7Si] 34 Table 29 : Alloy EN AW-6063A [AI Mg0,7Si(A)] 35 Table 30 : Alloy EN AW-6065 [AI Mg1Bi1Si] 36 Table 31 : Alloy EN AW-6082 [AI Si1MgMn]37 Table 32 : Alloy EN AW-7020 [AI Zn4,5Mg1] 38 Table 33 : Alloy EN AW-7022 [AI Zn5Mg3Cu]39 Table 34 : Alloy EN AW-7049A [AI Zn8MgCu] 40 Table 35 : Alloy EN AW-7075 [AI Zn5,5MgCu] 41

Table 5 — Alloy EN AW-2011A [Al Cu6BiPb(A)] Drawn rod/bar Dimensions mm Rm MPa R p0,2 MPa Temper D a S b min. max. min. max. A % min. A50 mm % min. HBW Typical value T3 ≤ 40 40 < D ≤ 50 50 < D ≤ 80 ≤ 40 40 < S ≤ 50 50 < S ≤ 80 320 300 280 - - - 270 250 210 - - - 10 10 10 8 - - 90 90 90 T8 ≤ 80 ≤ 80 370 - 270 - 8 6 115 Drawn tube Rm MPa R p0,2 MPa Temper Wall thickness t mm min. max. min. max. A % min. A50 mm % min. HBW Typical value T3 c ≤ 5 5 < t ≤ 20 310 290 - - 260 240 - - 10 8 8 6 90 90 T8 ≤ 20 370 - 275 - 8 6 115 a D = Diameter for round bar c S = Width across flats for square and hexagonal bar, thickness for rectangular bar c Properties may be obtained by press quenching
...