Aerospace series - Titanium Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) - Rm ≥ 1 300 MPa - Bars - De < 110 mm

This standard specifies the requirements relating to:
Titanium Ti-P63002 (Ti5Al5Mo5V3Cr0,4Fe)
Rm >or= 1 300 MPa
Bars
De for aerospace applications.

Luft- und Raumfahrt - Titan Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) - Rm ≥ 1 300 MPa - Stangen - De < 110 mm

Diese Norm legt die Anforderungen an
Titan Ti-P63002 (Ti5Al5Mo5V3Cr0,4Fe) Rm >/= 1 300 MPa Stangen De zur Anwendung in der Luft- und Raumfahrt fest.

Série aérospatiale - Titanium Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) - Rm ≥ 1 300 MPa - Barres - De < 110 mm

Aeronavtika - Titan Ti-P63002 (Ti5Al5Mo5V3Cr0,4Fe) - Rm ≥ 1300 MPa - Palice - De < 110 mm

Ta standard določa zahteve, ki se nanašajo na:
titan Ti-P63002 (Ti5Al5Mo5V3Cr0,4Fe),
Rm ≥ = 1300 MPa
palice
De < 110 mm
za uporabo v aeronavtiki.

General Information

Status
Published
Publication Date
28-Jun-2011
Technical Committee
Drafting Committee
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
01-Jun-2017

Buy Standard

Standard
EN 4675:2011
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.49.025.30TitanTitaniumICS:Ta slovenski standard je istoveten z:EN 4675:2011SIST EN 4675:2011en01-december-2011SIST EN 4675:2011SLOVENSKI

STANDARD
SIST EN 4675:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4675
June 2011 ICS 49.025.30 English Version

Aerospace series - Titanium Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) -Rm ≥ 1 300 MPa - Bars - De < 110 mm

Série aérospatiale - Titanium Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) - Rm ≥ 1 300 MPa - Barres - De < 110 mm

Luft- und Raumfahrt - Titan Ti-P63002 (Ti5Al5Mo5V3Cr0.4Fe) - Rm ≥ 1 300 MPa - Stangen -De < 110 mm This European Standard was approved by CEN on 9 October 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,

B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4675:2011: ESIST EN 4675:2011

EN 4675:2011 (E) 2 Contents Page Foreword .............................................................................................................................................................. 3 Introduction ......................................................................................................................................................... 4 1 Scope ...................................................................................................................................................... 5 2 Normative references ............................................................................................................................ 5

SIST EN 4675:2011

EN 4675:2011 (E) 3 Foreword This document (EN 4675:2011) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.