iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14336:2004

(Main)

Heating systems in buildings - Installation and commissioning of water based heating systems

Heating systems in buildings - Installation and commissioning of water based heating systems

This European Standard specifies the requirements for the installation and commissioning of water-based heating systems in buildings with a maximum operating temperature of 110 oC and a maximum operating pressure of 6 bar.
This standard covers the system's requirements for the installation and commissioning of individual components of the system (e.g. heat generators, pumps, controls). It does not cover the specific commissioning requirements for these components.
This standard does not cover the installation or commissioning of attached systems (e.g. air conditioning, domestic hot water or ventilation systems).
This standard covers only the technical requirements, and does not cover any commercial or contractual arrange-ments between parties.

Heizungsanlagen in Gebäuden - Installation und Abnahme der Warmwasser-Heizungsanlagen

Diese Norm legt Anforderungen für die Installation und die Abnahme von Warmwasserheizungsanlagen in Gebäuden mit einer maximalen Betriebstemperatur bis 110°C und einem maximalen Betriebsdruck von 6 bar fest.
Diese Norm gilt nicht für die Installation und die Abnahme von zugeschalteten Anlagen (z. B. Klimaanlagen, Hauswasseranlagen oder Lüftungsanlagen).
Diese Norm legt nur die technischen Voraussetzungen fest und regelt nicht das vertragliche Verhältnis zwischen Auftraggeber und Auftragnehmer (Planer und Ausführenden).

Systèmes de chauffage dans les bâtiments - Installation et commissionnement des systèmes de chauffage à eau

Le présent document spécifie les exigences relatives à l'installation et au commissionnement des systèmes de chauffage à eau des bâtiments fonctionnant avec une  température maximale de 110 °C et une pression maximale de fonctionnement  de 6 bars.
Le présent document couvre les spécifications pour l'installation et le commissionnement des composants du système (par exemple les générateurs, circulateurs, régulateurs). Il ne concerne pas les opérations de commissionnement spécifiques à ces composants.  
La présente norme ne couvre pas l'installation ou le commissionnement des systèmes connexes (p.ex. systèmes de conditionnement d'air, de production d'eau chaude domestique ou de ventilation).
Le présent document couvre les spécifications techniques, il ne concerne pas les accords contractuels ou commerciaux entre les parties.

Ogrevalni sistemi v stavbah - Vgradnja in zagon toplovodnih sistemov

General Information

Status
Published
Publication Date
05-Oct-2004
Withdrawal Date
29-Apr-2005
ICS
91.140.10 - Central heating systems
Technical Committee
CEN/TC 228 - Heating systems in buildings
Drafting Committee
CEN/TC 228/WG 2 - Installation and commissioning
Current Stage
9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
Completion Date
05-Mar-2023
Ref Project
SIST EN 14336:2005 - Heating systems in buildings - Installation and commissioning of water based heating systems

Relations

Revised
prEN 14336 - Heating systems in buildings - Installation and commissioning of water based heating systems
Effective Date
29-Aug-2018

Buy Standard

EN 14336:2005EN 14336:2005
PreviousNext
Standard
EN 14336:2005
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ogrevalni sistemi v stavbah - Vgradnja in zagon toplovodnih sistemovHeizungsanlagen in Gebäuden - Installation und Abnahme der Warmwasser-HeizungsanlagenSystemes de chauffage dans les bâtiments - Installation et commissionnement des systemes de chauffage a eauHeating systems in buildings - Installation and commissioning of water based heating systems91.140.10Sistemi centralnega ogrevanjaCentral heating systemsICS:Ta slovenski standard je istoveten z:EN 14336:2004SIST EN 14336:2005en01-marec-2005SIST EN 14336:2005SLOVENSKI
STANDARD



SIST EN 14336:2005



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14336October 2004ICS 91.140.10 English versionHeating systems in buildings - Installation and commissioning ofwater based heating systemsSystèmes de chauffage dans les bâtiments - Installation etmise en systèmes de chauffage à eauHeizungsanlagen in Gebäuden - Installation und Abnahmeder Warmwasser-HeizungsanlagenThis European Standard was approved by CEN on 29 July 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14336:2004: ESIST EN 14336:2005



EN 14336:2004 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Installation.6 4.1 Coordination of the work.6 4.2 Inventory and inspection.6 4.3 Handling.6 4.4 Storage.6 4.5 Installation of components.6 4.5.1 General.6 4.5.2 Heat supply.7 4.5.3 Heat distribution.7 4.5.4 Heat emission.7 4.5.5 Control and monitoring.7 4.5.6 Thermal insulation.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 11855-5:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 5: Installation (ISO 11855-5:2021)
SIST EN ISO 11855-5:2021

This document establishes requirements for the installation of embedded radiant heating and cooling systems. It specifies general and uniform requirements for the design and construction of heating and cooling floors, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application. The requirements specified by this document are applicable only to the components of the heating/cooling systems and the elements which are part of the heating/cooling surface and which are installed due to the heating/cooling systems.
This document is applicable to water-based embedded surface heating and cooling systems in residential, commercial and industrial buildings. The methods apply to systems integrated into the wall, floor or ceiling construction without any open-air gaps, but are not applicable to panel systems with open-air gaps which are not integrated into the building structure.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-4:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) (ISO 11855-4:2021)
SIST EN ISO 11855-4:2021

This document allows the calculation of peak cooling capacity of Thermo Active Building Systems (TABS), based on heat gains, such as solar gains, internal heat gains, and ventilation, and the calculation of the cooling power demand on the water side, to be used to size the cooling system, as regards the chiller size, fluid flow rate, etc.
This document defines a detailed method aimed at the calculation of heating and cooling capacity in non-steady state conditions.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-3:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning (ISO 11855-3:2021)
SIST EN ISO 11855-3:2021

This document establishes a system design and dimensioning method to ensure the heating and cooling capacity of the radiant heating and cooling systems.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11855-1:2021(Main)
Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria (ISO 11855-1:2021)
SIST EN ISO 11855-1:2021

This document specifies the basic definitions, symbols, and comfort criteria for embedded radiant heating and cooling systems.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15316-4-2:2017/AC:2017(Corrigendum)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
SIST EN 15316-4-2:2018/AC:2018
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12831-1:2017(Main)
Energy performance of buildings - Method for calculation of the design heat load - Part 1: Space heating load, Module M3-3
SIST EN 12831-1:2018

This European Standard covers methods for the calculation of the design heat load for single rooms, building entities and buildings, where the design heat load is defined as the heat supply (power) needed to maintain the required internal design temperature under design external conditions.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 -1.
NOTE 1   In CEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
(...)

  • Standard
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12831-3:2017(Main)
Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3
SIST EN 12831-3:2018

This European Standard describes a method to calculate the power and the storage volume required for the dimensioning of domestic hot water systems (DHW). The applicability ranges from direct water heaters (no storage volume and a comparatively large effective heating power) to larger storage systems with a comparatively small heating power and large storage volumes.
This European Standard is applicable to the following water storage systems:
-   storage systems characterized by a minimal mixing zone, (such as stratified charging storage tanks or storage tanks with external heat exchangers): these systems are nominated in this standard as "charging storage systems";
-   storage tank water heaters and warm water storage tanks with a pronounced mixing zone (such as DHW storage tanks with internal heat exchangers), nominated in this standard as "mixed storage systems";
and for different uses.
The Scope also includes standardization methods for determining the energy need for domestic hot water. This European Standard covers the domestic hot water needs in buildings.
The calculation of the energy needs for DHW-Systems applies to residential and non-residential buildings, a building or a zone of a building.
Figure 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000-1.
NOTE 1   In CEN ISO/TR 52000-2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
Table 1 shows the relative position of this standard within the EPB package of standards.
(...)

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15459-1:2017(Main)
Energy performance of buildings - Economic evaluation procedure for energy systems in buildings - Part 1: Calculation procedures, Module M1-14
SIST EN 15459-1:2018

This European Standard provides a calculation method for the economic issues of heating systems and other systems that are involved in the energy demand and consumption of the building. It applies to all types of new and existing buildings.
The fundamental principles and terminology are explained in the standard.
The main items of the standard will be:
-   the definitions and the structure of the types of costs which should be taken into account for the calculation of the economic efficiency of saving options in buildings;
-   data needed for definition of costs related to systems under consideration;
-   the calculation method(s);
-   expression of the result of the economic study.
This European Standard is part of the method for calculation of economic performance of energy saving options in buildings (e.g. insulation, better performing generators and distribution systems, efficient lighting, renewable sources, combined heat and power...).
The scope of this specific part is to standardize:
-   the required inputs;
-   the required outputs;
-   the calculation formulas;
-   the type of energy systems concerned with the energy performance of the building.
NOTE 1   This is the revision of EN 15459:2007. The revision has been made consistent with the EU regulation on cost-optimal. This revision includes the definition of payback for investment, and inclusion of the costs due to the deconstruction of the building. The method presenting annualized costs has been suppressed.
NOTE 2   This standard does not consider financial advantages for higher productivity, higher attractiveness for tenants due to higher indoor comfort, when relevant for comparison of different options.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000-1.
NOTE 3   In CEN ISO/TR 52000-2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 4   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
(...)

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15316-4-1:2017(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-1: Space heating and DHW generation systems, combustion systems (boilers, biomass), Module M3-8-1, M8-8-1
SIST EN 15316-4-1:2018

This European Standard is part of a series of standards on the method for calculation of system energy requirements and system efficiencies of space heating systems and domestic hot water systems.
This standard (EN 15316 4 1) specifies:
-   required inputs;
-   a calculation method;
-   resulting outputs;
-   a method to take into account the energy performance of heat generation devices based on fuel combustion;
for space heating generation by combustion sub-systems (boilers, biomass), including control.
This standard specifies methods for the calculation of:
-   thermal losses from the heating and the domestic hot water generation system;
-   recoverable thermal losses for space heating from the heating and the domestic hot water generation system;
-   auxiliary energy of the heating and the domestic hot water generation systems.
This standard specifies the energy performance calculation of water based heat generation sub-systems including control based on combustion of fuels ("boilers"), operating with conventional fossil fuels as well as renewable fuels. This standard does not cover sizing or inspection of boilers.
This standard is also applicable to heat generators for heating or for combined service as domestic hot water, ventilation, cooling and heating. Generators for domestic hot water only are taken into account into part M8-8.
This European Standard is the general standard on generation by combustion sub-systems (boilers, biomass) and is also intended for generation for domestic hot water production and/or space heating. These values are input data for calculation of the overall energy use according to EN ISO 52000 1 and EN 15316 1.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 1.
NOTE 1   In CEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15316-5:2017(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 5: Space heating and DHW storage systems (not cooling), Module M3-7, M8-7
SIST EN 15316-5:2018

This European Standard covers energy performance calculation of water based storage sub-systems used for heating, for domestic hot water or for combination of these.
This standard does not cover sizing or inspection of such storage systems.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000-1.
NOTE 1   In CEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day