prEN ISO 7719
(Main)Fasteners - Prevailing torque hexagon nuts - Regular nuts (all metal) (ISO/DIS 7719:2024)
Fasteners - Prevailing torque hexagon nuts - Regular nuts (all metal) (ISO/DIS 7719:2024)
ISO 7719:2012 specifies the characteristics of prevailing torque type all-metal hexagon regular nuts with threads from M5 up to and including M36, in product grade A for threads up to and including M16 and product grade B for threads above M16, and with property classes 5, 8 and 10.
Verbindungselemente - Sechskantmuttern mit Klemmteil - Normalhohe Muttern (Ganzmetallmuttern) (ISO/DIS 7719:2024)
Fixations - Écrous hexagonaux autofreinés - Écrous normaux (tout métal) (ISO/DIS 7719:2024)
L'ISO 7719:2012 spécifie les caractéristiques des écrous hexagonaux normaux autofreinés tout métal, de diamètre de filetage M5 à M 36 inclus, de grade A pour les filetages jusqu'à M 16 et de grade B pour les filetages supérieurs à M16, et de classes de qualité 5, 8 et 10.
Vezni elementi - Šestrobe zaščitne matice - Navadni matice (vse kovine) (ISO/DIS 7719:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Nadomešča:
SIST EN ISO 7719:2014/AC:2014
Vezni elementi - Šestrobe zaščitne matice - Navadni matice (vse kovine) (ISO/DIS
7719:2024)
Fasteners - Prevailing torque hexagon nuts - Regular nuts (all metal) (ISO/DIS
7719:2024)
Verbindungselemente - Sechskantmuttern mit Klemmteil - Normalhohe Muttern
(Ganzmetallmuttern) (ISO/DIS 7719:2024)
Fixations - Écrous hexagonaux autofreinés - Écrous normaux (tout métal) (ISO/DIS
7719:2024)
Ta slovenski standard je istoveten z: prEN ISO 7719
ICS:
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 7719
ISO/TC 2/SC 12
Fasteners — Prevailing torque
Secretariat: DIN
hexagon nuts — Regular nuts (all
Voting begins on:
metal)
2024-06-06
Fixations — Écrous hexagonaux autofreinés — Écrous normaux
Voting terminates on:
(tout métal)
2024-08-29
ICS: 21.060.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 7719:2024(en)
DRAFT
ISO/DIS 7719:2024(en)
International
Standard
ISO/DIS 7719
ISO/TC 2/SC 12
Fasteners — Prevailing torque
Secretariat: DIN
hexagon nuts — Regular nuts
Voting begins on:
(all metal)
Fixations — Écrous hexagonaux autofreinés — Écrous normaux
Voting terminates on:
(tout métal)
ICS: 21.060.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 7719:2024(en)
ii
ISO/DIS 7719:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 3
6 Marking and labelling . 4
6.1 Marking on product . .4
6.2 Labelling on package .5
7 Designation . 5
Bibliography . 6
iii
ISO/DIS 7719:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO’s adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners
with metric internal thread.
This fourth edition cancels and replaces the third edition (ISO 7719:2012) which has been technically
revised.
The main changes are as follows:
— the design principles of these nuts have been clarified in scope (see Note);
— style, relevant property classes and related quenching and tempering conditions for steel nuts have been
specified in Clause 5 in accordance with ISO 898-2 (see Table 3);
— stainless steel nuts have been added in accordance with ISO 3506-2;
— M7, M27, M33 and M39 have been added;
— d , d and m have been specified with two decimal places;
a,max w,min w,min
— d for M5 has been changed from s – IT16 to s – IT15 in order to have a larger bearing surface
w,min min min
area and thus less contact pressure;
— h for M5 and M6 has been amended to style 1 in accordance with the scope of this document, and h
min max
has been decreased accordingly (see Table 1);
— specifications for marking and labelling have been added as Clause 6.
Any feedback or questions on this document should be directed to the user's national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT International Standard ISO/DIS 7719:2024(en)
Fasteners — Prevailing torque hexagon nuts — Regular nuts
(all metal)
1 Scope
This document specifies the characteristics of prevailing torque (all metal) hexagon regular nuts, in steel
and stainless steel, with metric coarse pitch thread M5 to M39, and with product grades A and B.
NOTE These nuts are designed with an overall height h = m (as specified in ISO 898-2 and ISO 4032 for style
min min
1) plus the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.