Free-standing chimneys - Part 6: Steel liners - Design and execution

This document deals with special requirements and performance criteria for the design of lining systems made of steel for free standing chimneys. It specifies the requirements for cylindrical steel liners as stated in EN 13084 1.
This document covers the design of the following three basic types of liners located in a load bearing structure:
a)   base supported liner;
b)   sectional liner;
c)   top hung liner.
Additionally this document applies to single wall chimneys regarding their contact with flue gases.
For simplicity, these various designs will generally be referred to herein as "liners".
The mechanical requirement is not part of this document, for information see prEN 1993 3.
NOTE   Liners built from prefabricated metal chimneys in accordance with EN 1856 1:2009 and
EN 1856 2:2009 are installed as base supported liners with additional supports and guides as defined in this document.

Freistehende Schornsteine - Teil 6: Innenrohre aus Stahl - Bemessung und Ausführung

Dieses Dokument befasst sich mit den besonderen Anforderungen und Ausführungskriterien für das Bemessen und Konstruieren von Innenrohrkonstruktionen aus Stahl bei freistehenden Schornsteinen. Es legt die Anforderungen an zylindrische Innenrohre aus Stahl, wie in EN 13084 1 angegeben, fest.
Dieses Dokument gilt für das Bemessen und Konstruieren folgender drei Grundtypen von Innenrohren, die sich in einer tragenden Konstruktion befinden:
a)   unten abgestütztes Innenrohr;
b)   Etageninnenrohr;
c)   hängendes Innenrohr.
Das vorliegende Dokument gilt zusätzlich für einwandige Schornsteine, die mit den Abgasen in Berührung kommen.
Der Einfachheit halber werden verschiedene Bemessungen hier grundsätzlich als "Innenrohre" bezeichnet.
Die mechanischen Anforderungen sind nicht Teil dieses Dokuments. Für Informationen siehe prEN 1993 3.
ANMERKUNG   Innenrohre aus vorgefertigten Metallschornsteinen nach EN 1856 1:2009 und EN 1856 2:2009 werden als unten abgestützte Innenrohre mit zusätzlichen Abstützungen und Führungen, wie in diesem Dokument definiert, eingebaut.

Cheminées autoportantes - Partie 6: Parois intérieures en acier - Conception et mise en oeuvre

Le présent document traite des exigences spécifiques et des critères de performance concernant la conception de systèmes de parois intérieures en acier destinés aux cheminées autoportantes. Il spécifie les exigences relatives aux parois intérieures cylindriques en acier données dans l’EN 13084 1.
Ce document couvre la conception des trois types de paroi de base qui se trouvent dans la structure porteuse :
a)   paroi intérieure soutenue à la base ;
b)   paroi intérieure en tronçons ;
c)   paroi intérieure suspendue par le haut.
De plus, ce document s’applique aux cheminées à paroi simple en ce qui concerne leur contact avec les fumées.
Par souci de simplicité, ces différentes conceptions sont généralement désignées ci-après par le terme de « parois intérieures ».
Les exigences mécaniques ne font pas partie du présent document. Pour plus d’informations, voir le prEN 1993 3.
NOTE   Les parois réalisées à partir de conduits métalliques préfabriqués conformément à l’EN 1856 1:2009 et l’EN 1856 2:2009 sont installées comme parois intérieures soutenues à la base avec des supports et guides supplémentaires tels que définis dans le présent document.

Prostostoječi dimniki - 6. del: Jeklene tuljave - Projektiranje in izvedba

General Information

Status
Not Published
Publication Date
10-Dec-2025
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
03-Oct-2024
Due Date
25-Jul-2024
Completion Date
03-Oct-2024

Relations

Buy Standard

Draft
prEN 13084-6:2024
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2024
Prostostoječi dimniki - 6. del: Jeklene tuljave - Projektiranje in izvedba
Free-standing chimneys - Part 6: Steel liners - Design and execution
Freistehende Schornsteine - Teil 6: Innenrohre aus Stahl - Bemessung und Ausführung
Cheminées autoportantes - Partie 6: Parois intérieures en acier - Conception et mise en
oeuvre
Ta slovenski standard je istoveten z: prEN 13084-6
ICS:
91.060.40 Dimniki, jaški, kanali Chimneys, shafts, ducts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2024
ICS 91.060.40 Will supersede EN 13084-6:2015
English Version
Free-standing chimneys - Part 6: Steel liners - Design and
execution
Cheminées autoportantes - Partie 6: Parois intérieures Freistehende Schornsteine - Teil 6: Innenrohre aus
en acier - Conception et mise en oeuvre Stahl - Bemessung und Ausführung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 297.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13084-6:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Material . 6
4.1 General. 6
4.2 Steels. 7
5 General design and construction requirements . 7
5.1 General. 7
5.2 Construction details . 7
5.2.1 General. 7
5.2.2 Supports and/or guides . 8
5.2.3 Openings in liners . 8
5.2.4 Drainage system . 9
5.2.5 Seals, gaskets and jointing compounds . 9
5.2.6 Expansion joints . 9
5.2.7 Insulation . 9
5.2.8 Coating . 9
5.2.9 Cladding . 10
5.2.10 Internal protection . 10
5.2.11 Lightning protection . 10
5.3 Gas tightness . 10
5.4 Temperature classes. 11
6 Structural design . 11
6.1 Altimetry and geometry . 11
6.2 Actions . 13
6.2.1 General. 13
6.2.2 Permanent action . 13
6.2.3 Deflection of bearing system . 13
6.2.4 Wind suction . 13
6.2.5 Thermal actions . 14
6.2.6 Internal pressure at design conditions . 15
6.3 Verification . 16
6.3.1 General. 16
6.3.2 Mechanical characteristics . 16
7 Fabrication . 16
7.1 Tolerances . 16
7.2 Surface protection against chemical attack . 16
Bibliography . 17
European foreword
This document (prEN 13084-6:2024) has been prepared by Technical Committee CEN/TC 297 “Free-
standing industrial chimneys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13084-6:2015.
EN 13084-6:2015:
— reformulation of the scope,
— additions to the terms and definitions,
— revision and addition of subclause 5.2, “Construction details“,
— revision and addition of Clause 6 “Structural design“,
— deletion of Annex A which was transfered in FprEN 13084-1.
This document is part one of the package of standards listed below:
— EN 13084-1, Free-standing chimneys — Part 1: General requirements
— EN 13084-2, Free-standing chimneys — Part 2: Concrete chimneys
— EN 13084-4, Free-standing chimneys — Part 4: Brick liners — Design and execution
— EN 13084-5, Free-standing chimneys — Part 5: Material for brick liners — Product specifications
— EN 13084-6, Free-standing chimneys — Part 6: Steel liners — Design and execution
— EN 13084-7, Free-standing chimneys — Part 7: Product specifications of cylindrical steel fabrications
for use in single wall steel chimneys and steel liners
— EN 13084-8, Free-standing chimneys — Part 8: Design and execution of mast construction with
satellite components
— EN 13084-9, Free-standing chimneys — Part 9: Monitoring, inspection, maintenance, remedial and
reporting; operations and actions required
— prEN 1993-3, Eurocode 3: Design of steel structures — Part 3: Towers, masts and chimneys
1 Scope
This document deals with special requirements and performance criteria for the design of lining
systems made of steel for free standing chimneys. It specifies the requirements for cylindrical steel
liners as stated in EN 13084-1.
This document covers the design of the following three basic types of liners located in a load bearing
structure:
a) base supported liner;
b) sectional liner;
c) top hung liner.
Additionally this document applies to single wall chimneys regarding their contact with flue gases.
For simplicity, these various designs will generally be referred to herein as “liners”.
The mechanical requirement is not part of this document, for information see prEN 1993-3.
NOTE Liners built from prefabricated metal chimneys in accordance with EN 1856-1:2009 and
EN 1856-2:2009 are installed as base supported liners with additional supports and guides as defined in this
document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1090-2:2018, Execution of steel structures and aluminium structures — Part 2: Technical
requirements for steel structures
EN 1443:2019, Chimneys — General requirements
EN 1856-1:2009, Chimneys — Requirements for metal chimneys — Part 1: System chimney products
EN 1856-2:2009, Chimneys — Requirements for metal chimneys — Part 2: Metal flue liners and
connecting flue pipes
EN 1859:2009+A1:2013, Chimneys — Metal chimneys — Test methods
EN 1991-1-4, Eurocode 1: Actions on structures — Part 1-4: General actions — Wind actions
EN 1993-1-6, Eurocode 3 — Design of steel structures — Part 1-6: Strength and Stability of Shell
Structures
prEN 1993-3, Eurocode 3 — Design of steel structures — Part 3: Towers, masts and chimneys
EN 10028 (all parts), Flat products made of steels for pressure purposes
EN 10088 (all parts), Stainless steels
EN 10095, Heat resisting steels and nickel alloys
FprEN 13084-1:2024, Free-standing chimneys — Part 1: General requirements
EN 13084-7:2012, Free-standing chimneys — Part 7: Product specifications of cylindrical steel
fabrications for use in single wall steel chimneys and steel liners
EN 62305-1, Protection against lightning — Part 1: General principles
EN ISO 5817:2014, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam
welding excluded) — Quality levels for imperfections (ISO 5817:2014)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in FprEN 13084-1:2024 and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
base supported liner
liner which is supported vertically only at the liner base
3.2
chemical resistance of steel liners
ability of the lining system to withstand corrosion due to the corrosivity of the flue gases which it
conveys
3.3
condensate and water resistance
ability of the liner to prevent condensate and/or water from escaping out of the liner to its outer
surface or in
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.