Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2023)

This document specifies the method for Rockwell regular and Rockwell superficial hardness tests for scales A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T, and 45T for metallic materials and is applicable to stationary and portable hardness testing machines.
For specific materials and/or products, other specific International Standards apply (e.g. ISO 3738-1 and ISO 4498).

Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil 1: Prüfverfahren (ISO 6508-1:2023)

Dieses Dokument legt die Härteprüfung nach dem Standard-Rockwell- und Superrockwell-Verfahren für die Skalen A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T und 45T für metallene Werkstoffe fest und ist anwendbar für ortsfeste und mobile Härteprüfmaschinen.
Für Sonderwerkstoffe und/oder -erzeugnisse gelten andere besondere Internationale Normen (z. B. ISO 3738 1 und ISO 4498).

Matériaux métalliques - Essai de dureté Rockwell - Partie 1: Méthode d'essai (ISO 6508-1:2023)

Le présent document spécifie la méthode d’essai de dureté Rockwell normale et de dureté Rockwell superficielle pour les échelles A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T et 45T pour les matériaux métalliques. Elle s'applique aux machines d’essai de dureté fixes et portables.
Pour des matériaux et/ou produits spécifiques, d’autres Normes internationales spécifiques s’appliquent (par exemple, ISO 3738-1 et ISO 4498).

Kovinski materiali - Preskus trdote po Rockwellu - 1. del: Preskusna metoda (ISO 6508-1:2023)

Ta dokument določa metodo običajnega preskusa trdote po Rockwellu in preskusa trdote z majhnimi obremenitvami po Rockwellu za
vrednosti A, B, C, D, E, F, G, H, K,15N, 30N, 45N, 15T, 30T in 45T za kovinske materiale in se uporablja za nepremične in premične naprave za preskušanje trdote.
Za določene materiale in/ali izdelke se uporabljajo drugi ustrezni mednarodni standardi (na primer ISO 3738-1 in ISO 4498).

General Information

Status
Published
Publication Date
19-Dec-2023
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Dec-2023
Completion Date
20-Dec-2023

Relations

Buy Standard

Standard
EN ISO 6508-1:2024
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2024
Kovinski materiali - Preskus trdote po Rockwellu - 1. del: Preskusna metoda (ISO
6508-1:2023)
Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2023)
Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil 1: Prüfverfahren (ISO 6508-
1:2023)
Matériaux métalliques - Essai de dureté Rockwell - Partie 1: Méthode d'essai (ISO 6508-
1:2023)
Ta slovenski standard je istoveten z: EN ISO 6508-1:2023
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 6508-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 6508-1:2016
English Version
Metallic materials - Rockwell hardness test - Part 1: Test
method (ISO 6508-1:2023)
Matériaux métalliques - Essai de dureté Rockwell - Metallische Werkstoffe - Härteprüfung nach Rockwell -
Partie 1: Méthode d'essai (ISO 6508-1:2023) Teil 1: Prüfverfahren (ISO 6508-1:2023)
This European Standard was approved by CEN on 13 November 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6508-1:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 6508-1:2023) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee CEN/TC 459/SC 1 “Test
methods for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2024, and conflicting national standards shall be
withdrawn at the latest by June 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6508-1:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 6508-1:2023 has been approved by CEN as EN ISO 6508-1:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 6508-1
Fifth edition
2023-12
Metallic materials — Rockwell
hardness test —
Part 1:
Test method
Matériaux métalliques — Essai de dureté Rockwell —
Partie 1: Méthode d'essai
Reference number
ISO 6508-1:2023(E)
ISO 6508-1:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 6508-1:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols, abbreviated terms and designations . 1
5 Rockwell hardness . .3
6 Testing machine.4
7 Test piece . 5
8 Procedure .5
9 Uncertainty of the results . 7
10 Test report . 7
11 Conversions to other hardness scales or tensile strength values .8
Annex A (normative) Special HR30TSm and HR15TSm test for thin products .9
Annex B (normative) Minimum thickness of the test piece in relation to the Rockwell
hardness .10
Annex C (normative) Corrections to be added to Rockwell hardness values obtained on
convex cylindrical surfaces .13
Annex D (normative) Corrections to be added to Rockwell hardness C scale values obtained
on spherical test surfaces of various diameters .16
Annex E (normative) Daily verification procedure .17
Annex F (normative) Inspection of diamond indenters .20
Annex G (informative) Uncertainty of the measured hardness values .21
Annex H (informative) CCM — Working group on hardness .26
Annex I (informative) Rockwell hardness measurement traceability .27
Bibliography .31
iii
ISO 6508-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals,
Subcommittee SC 3, Hardness testing, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 459, ECISS - European Committee for Iron and Steel Standardization,
in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This fifth edition cancels and replaces the fourth edition (ISO 6508-1:2016), which has been technically
revised.
The main changes are as follows:
— removal of note related to the use of tungsten and steel ball indenters (Clause 1);
— removal of the year from the Normative References specified and various places throughout the
body of the standard (Clause 2);
— addition of Clause 3, Terms and definitions;
— added additional information for the use of single-piece spherically tipped indenters (6.3 NOTE 1);
— added the table reference and table title (7.4);
— modified the uncertainty of the results section to only provide a single reference for the determination
of uncertainty (Clause 9);
— modified Annex G to remove the “procedure without bias (M2)” method for determining uncertainty.
A list of all parts in the ISO 6508 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 6508-1:2023(E)
Metallic materials — Rockwell hardness test —
Part 1:
Test method
1 Scope
This document specifies the method for Rockwell regular and Rockwell superficial hardness tests for
scales A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T, and 45T for metallic materials and is applicable to
stationary and portable hardness testing machines.
For specific materials and/or products, other specific International Standards apply (e.g. ISO 3738-1
and ISO 4498).
2 Normative references
The following documents are
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.