EN 10058:2018

Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions

This document specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel flat bars and steel wide flats for general purposes.
This document is not applicable to spring leaves, see EN 10092-1.

Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung - Maße, Formtoleranzen und Grenzabmaße

Diese Europäische Norm legt die Nennmaße, Grenzabmaße und Formtoleranzen für warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung fest.
Diese Norm gilt nicht für Flachstäbe für Federn, siehe EN 10092-1.

Plats et larges plats en acier laminés à chaud pour usages généraux - Dimensions et tolérances sur la forme et les dimensions

La présente Norme européenne spécifie les dimensions nominales et les tolérances sur les dimensions et la forme des plats et larges plats en acier laminés à chaud pour usages généraux.
La présente norme ne s’applique pas aux lames de ressorts, voir l’EN 10092-1.

Vroče valjane ploske jeklene palice in jeklene široke plošče za splošne namene - Mejni odstopki mer in tolerance oblik

Ta evropski standard določa nazivne mejne odstopke mer in tolerance oblik vroče valjanih ploskih jeklenih palic in jeklenih širokih plošč za splošne namene.
Ta standard se ne uporablja za listnate vzmeti, glej standard EN 10092-1.

General Information

• Status: Published
• Publication Date: 27-Nov-2018
• Withdrawal Date: 30-May-2019
• ICS: 77.140.60 - Steel bars and rods
• Technical Committee: ECISS/TC 103 - Structural steels other than reinforcements
• Drafting Committee: ECISS/TC 103/WG 5 - Hot rolled steel channels, I and H sections
• Ref Project: SIST EN 10058:2019 - Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions

Relations

• Replaces: EN 10058:2003 - Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape and dimensions
• Effective Date: 23-Jan-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung - Maße, Formtoleranzen und GrenzabmaßePlats et larges plats en acier laminés à chaud pour usages généraux - Dimensions et tolérances sur la forme et les dimensionsHot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions77.140.60Jeklene palice in drogoviSteel bars and rodsICS:Ta slovenski standard je istoveten z:EN 10058:2018SIST EN 10058:2019en,fr,de01-februar-2019SIST EN 10058:2019SLOVENSKI
STANDARDSIST EN 10058:20041DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10058
November
t r s z ICS
y yä s v rä x r Supersedes EN
s r r w zã t r r uEnglish Version
Hot rolled flat steel bars and steel wide flats for general purposes æ Dimensions and tolerances on shape and dimensions Plats et larges plats en acier laminßs à chaud pour usages gßnßraux æ Dimensions et tolßrances sur la forme et les dimensions
Warmgewalzte Flachstäbe aus Stahl und Breitflachstahl für allgemeine Verwendung æ Maßeá Formtoleranzen und Grenzabmaße This European Standard was approved by CEN on
w October
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r r w zã t r s z ESIST EN 10058:2019

European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Designation. 4 5 Dimensions . 4 6 Tolerances on dimensions and shape . 6 6.1 Thickness (t) . 6 6.2 Width (b) . 6 6.3 Length (L) . 6 6.4 Straightness (q) . 6 6.5 Out-of-squareness (u) . 6 6.6 Maximum permissible variation in thickness across the width for wide flats . 6 7 Measurement . 8 7.1 Thickness and width . 8 7.2 Length . 8 7.3 Straightness . 8 7.4 Out-of-squareness . 8 7.5 Maximum permissible variation in thickness across the width for wide flats . 8 Bibliography . 9
...