Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements

This European Standard contains the relevant functional requirements for gas pressure regulating stations, which form part of gas transmission or distribution systems. It is applicable to the design, materials, construction, testing, operation and maintenance of gas pressure regulating stations.
This European Standard does not apply to gas pressure regulating stations commissioned prior to the publication of this standard.
The stations covered by this European Standard have a maximum upstream operating pressure which does not exceed 100 bar. For higher maximum upstream operating pressures this standard should be used as a guideline.
If the inlet pipework of the station is a service line and the maximum upstream operating pressure does not exceed 16 bar and the design flow rate is equal to or less than 200 m3/h under normal conditions, EN 12279 applies.
Basic system requirements for gas pressure regulating stations are contained in this European Standard. Requirements for individual components (valves, regulators, safety devices, pipes, etc.) or installation of the components are contained in the appropriate European Standards.
NOTE   For combined regulating and measuring stations, the additional requirements of EN 1776 can apply.
The requirements in this European Standard do not apply to the design and construction of auxiliary facilities such as sampling, calorimetering, odorization systems and density measuring. These facilities are covered by the appropriate European Standards, where existing, or other relevant standards.
The requirements of this European Standard are based on good gas engineering practice under conditions normally encountered in the gas industry. Requirements for unusual conditions cannot be specifically provided for, nor are all engineering and construction details prescribed.
The requirements in this European Standard are based on the physical and chemical data of gaseous fuels – including non-conventional gases – in accordance with Table 1 of EN 437:2003+A1:2009 for first and second family gases. Additional requirements in the case of gaseous fuels heavier than air and/or sour gases are not covered by this European Standard.
The objective of this European Standard is to ensure the safe operation of such stations. This does not, however, relieve all concerned of the responsibility for taking the necessary care and applying effective quality management during the design, construction and operation.

Gasinfrastruktur - Gas-Druckregelanlagen für Transport und Verteilung - Funktionale Anforderungen

Diese Europäische Norm beinhaltet die wesentlichen funktionalen Anforderungen für Gas-Druckregelanlagen in Gastransport- oder -verteilungssystemen. Sie gilt für Planung, Werkstoffe, Bau, Prüfung, Betrieb und Instandhaltung von Gas-Druckregelanlagen.
Diese Europäische Norm gilt nicht für Gas-Druckregelanlagen, die vor der Publikation dieser Norm in Betrieb genommen worden sind.
Diese Europäische Norm gilt für Anlagen mit maximal zulässigen eingangsseitigen Betriebsdrücken bis 100 bar. Für höhere, maximal zulässige, eingangsseitige Betriebsdrücke sollte diese Norm als eine Leitlinie herangezogen werden.
Wenn die Eingangsleitung der Anlage eine Anschlussleitung ist und der maximal zulässige eingangsseitige Betriebsdruck nicht höher als 16 bar und der Auslegungsdurchfluss nicht größer als 200 m3/h im Normzustand ist, gilt EN 12279.
Diese Europäische Norm behandelt grundsätzliche Systemanforderungen an Gas-Druckregelanlagen. Die Anforderungen an einzelne Komponenten (Armaturen, Regelgeräte, Sicherheitseinrichtungen, Rohre usw.) oder für den Einbau der Komponenten werden in den einschlägigen Europäischen Normen behandelt.
ANMERKUNG   Im Falle von kombinierten Mess- und Regelanlagen können die zusätzlichen Anforderungen nach EN 1776 zur Anwendung kommen.
Diese Europäische Norm gilt nicht für Planung und Errichtung von Hilfseinrichtungen, wie beispielsweise Probenahme, Brennwertmessung, Odorierung und Dichtemessung. Solche Einrichtungen werden in den einschlägigen Europäischen Normen, soweit vorhanden, oder anderen geeigneten Normen behandelt.
Die Anforderungen dieser Europäischen Norm basieren auf allgemein anerkannten Regeln der Gastechnik, wie sie unter gewöhnlichen Bedingungen in der Gasindustrie zur Anwendung kommen. Anforderungen hinsichtlich ungewöhnlicher Bedingungen sowie bautechnischer Details können nicht besonders berücksichtigt werden.
Diese Europäische Norm basiert auf den physikalischen und chemischen Daten von gasförmigen Brennstoffen – einschließlich der nicht-konventionellen Gase – der ersten und zweiten Gasfamilie entsprechend von EN 437:2009, Tabelle 1. Zusätzliche Anforderungen im Falle von gasförmigen Brennstoffen schwerer als Luft oder Sauergasen werden in dieser Europäischen Norm nicht behandelt.
Ziel dieser Europäischen Norm ist, den sicheren Betrieb der Gas-Druckregelanlagen sicherzustellen. Dies befreit jedoch die Verantwortlichen nicht davon, bei Planung, Bau und Betrieb mit der erforderlichen Sorgfalt vorzugehen und ein wirkungsvolles Qualitätsmanagement anzuwenden.

Infrastructures gazières - Postes de détente régulation de pression de gaz pour le transport et la distribution - Prescriptions fonctionnelles

La présente norme contient les prescriptions fonctionnelles relatives aux postes de détente régulation de pression de gaz faisant partie de réseaux de transport ou de distribution de gaz. Elle s'applique à la conception, aux matériaux, à la construction, aux essais, à l'exploitation et à la maintenance des postes de détente-régulation de pression de gaz (dénommés ci-après "postes de détente-régulation").
La présente Norme européenne ne s’applique pas aux postes de détente-régulation mis en service avant la publication de cette norme.
Les postes couverts par la présente Norme européenne ont une pression maximale de service en amont inférieure ou égale à 100 bar. Pour des pressions maximales de service en amont plus élevées, il convient d'utiliser la présente norme comme guide.
Si la tuyauterie d'entrée du poste est un branchement, et si la pression maximale de service en amont est inférieure à 16 bar et le débit de conception inférieur ou égal à 200 m3/h dans des conditions normales, l'EN 12279 s'applique.
Des prescriptions de base concernant les postes de détente-régulation de pression de gaz font partie de cette Norme européenne. Les prescriptions relatives aux composants individuels (robinets, détendeurs-régulateurs, dispositifs de sécurité, tubes, etc.) ou à l'installation des composants sont traitées dans les Normes européennes correspondantes.
NOTE   Dans le cas de postes de régulation et de comptage combinés, les prescriptions supplémentaires issues de l’EN 1776 peuvent être appliquées.
Les prescriptions de la présente Norme européenne ne s'appliquent pas à la conception et à la construction d'installations auxiliaires telles que systèmes d'échantillonnage, de calorimétrie, d'odorisation et de mesure de la densité. Ces types d’installations sont traités dans les Normes européennes appropriées, si elles existent, ou dans d’autres normes pertinentes.
Les prescriptions de la présente Norme européenne sont fondées sur une bonne pratique de l'ingénierie gazière, dans les conditions normalement rencontrées dans l'industrie du gaz. Les prescriptions pour les conditions inhabituelles ne peuvent pas être spécifiquement traitées, ni tous les détails relatifs à l'ingénierie et à la construction prescrits.
Les prescriptions de la présente Norme européenne s'appuient sur les données physiques et chimiques relatives aux gaz combustibles, y compris les gaz dits non conventionnels, conformément au Tableau 1 de l'EN 437:2003+A1:2009 pour les gaz des première et deuxième familles. Des prescriptions complémentaires pour les gaz combustibles plus lourds que l’air et/ou les gaz corrosifs, ne sont pas traitées dans la présente Norme européenne.
La présente Norme européenne a pour objet de garantir le fonctionnement en toute sécurité de ces postes. Toutefois, cela ne dégage pas de leur responsabilité l'ensemble des personnes concernées, qui doivent accorder toute l'attention nécessaire et mettre en application une gestion de la qualité efficace lors des phases de conception, de construction et d'exploitation.

Infrastruktura za plin - Plinske postaje za regulacijo tlaka za prenos in distribucijo - Funkcionalne zahteve

Ta evropski standard vsebuje relevantne funkcionalne zahteve za plinske postaje za regulacijo tlaka, ki so del plinskih sistemov za prenos ali distribucijo. Uporablja se pri obliki, materialih, konstrukciji, testiranju, obratovanju in vzdrževanju plinskih postaj za regulacijo tlaka.
Ta evropski standard se ne uporablja za plinske postaje za regulacijo tlaka, ki so obratovale pred objavo tega standarda.
Postaje, vključene v ta evropski standard, delujejo z največjim vhodnim delovnim tlakom, ki ne presega 100 barov. Pri višjih največjih vhodnih delovnih tlakih naj bi ta standard služil kot smernica.
Če je sesalni cevovod postaje priključni vod, največji vhodni delovni tlak ne preseže 16 barov, načrtovani pretok pa je enak ali manjši od 200 m³/h v normalnih razmerah, potem velja standard EN 12279.
V tem evropskem standardu so vključene osnovne sistemske zahteve za plinske postaje za regulacijo tlaka. Zahteve za posamezne sestavne dele (ventili, regulatorji, varnostne naprave, cevi itd.) ali inštalacija sestavnih delov so vsebovani v ustreznih evropskih standardih.
Pri kombiniranih postajah za regulacijo in merjenje je mogoče, da veljajo dodatne zahteve standarda EN 1776.
Zahteve v tem evropskem standardu se ne uporabljajo za projektiranje in gradnjo pomožnih obratov, kot so sistemi za vzorčenje, kalorimetrijo, odišavljenje in merjenje gostote. Ti obrati so zajeti v ustreznih evropskih standardih, če obstajajo, ali v drugih relevantnih standardih.
Zahteve tega evropskega standarda temeljijo na dobri tehnološki praksi oskrbe s plinom v razmerah, ki so običajne v plinski industriji. Zahtev za neobičajne razmere ni mogoče izrecno določiti, niti niso predpisane vse inženirske in gradbene podrobnosti.
Zahteve v tem evropskem standardu temeljijo na fizikalnih in kemijskih podatkih plinastih goriv, vključno z nekonvencionalnimi plini, v skladu s preglednico 1 standarda EN 437 2009 za pline prve in druge družine. Dodatne zahteve v primeru plinastih goriv, težjih od zraka, in/ali kislih plinov niso vključene v tem evropskem standardu.
Cilj tega evropskega standarda je zagotoviti varno delovanje takih postaj. To pa ne odvezuje vseh vpletenih, da med načrtovanjem, gradnjo in obratovanjem ne bi poskrbeli za ustrezne ukrepe in učinkovit sistem upravljanja kakovosti.
Ta evropski standard določa splošna osnovna načela za infrastrukturo za plin. Uporabniki tega evropskega standarda naj bi se zavedali, da lahko v državah članicah CEN obstajajo podrobnejši nacionalni standardi in/ali kodeksi ravnanja.
Ta evropski standard je namenjen uporabi v povezavi s temi nacionalnimi standardi in/ali kodeksi ravnanja, ki določajo zgoraj navedena osnovna načela.
Kadar so strožje zahteve v nacionalni zakonodaji/predpisih v nasprotju z zahtevami iz tega standarda, ima prednost nacionalna zakonodaja/predpis, kot je navedeno v standardu CEN/TR 13737 (vsi deli). CEN/TR 13737 navaja:
– pojasnitev celotne zakonodaje/vseh predpisov, ki veljajo v državi članici,
– po potrebi strožje nacionalne zahteve,
– nacionalno kontaktno točko za najnovejše informacije.

General Information

Status
Published
Publication Date
21-Oct-2014
Withdrawal Date
29-Apr-2015
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
03-Jun-2020
Completion Date
03-Jun-2020

Relations

Buy Standard

Standard
EN 12186:2015
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 12186:2013
English language
34 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Infrastruktura za plin - Plinske postaje za regulacijo tlaka za prenos in distribucijo - Funkcionalne zahteveGasinfrastruktur - Gas-Druckregelanlagen für Transport und Verteilung - Funktionale AnforderungenInfrastructures gazières - Postes de détente régulation de pression de gaz pour le transport et la distribution - Prescriptions fonctionnellesGas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements75.200Petroleum products and natural gas handling equipment23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 12186:2014SIST EN 12186:2015en,fr,de01-januar-2015SIST EN 12186:2015SLOVENSKI
STANDARDSIST EN 12186:2000/A1:2005SIST EN 12186:20001DGRPHãþD



SIST EN 12186:2015



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12186
October 2014 ICS 23.060.40; 27.060.20; 75.200 Supersedes EN 12186:2000English Version
Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
Infrastructures gazières - Postes de détente régulation de pression de gaz pour le transport et la distribution - Prescriptions fonctionnelles
Gasinfrastruktur - Gas-Druckregelanlagen für Transport und Verteilung - Funktionale Anforderungen This European Standard was approved by CEN on 13 September 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12186:2014 ESIST EN 12186:2015



EN 12186:2014 (E) 2 Contents Page
Foreword .4 1 Scope .6 2 Normative references .6 3 Terms, definitions, symbols and abbreviations .7 3.1 General .7 3.2 Station .8 3.3 Pressure, design and testing . 10 3.4 Pressure control . 11 3.5 Continuity of supply . 12 4 Quality and management system . 13 5 Environmental impact . 13 6 Layout of the gas pressure regulating station . 13 6.1 General . 13 6.2 Layout of the site . 14 6.3 Site security .
...

SLOVENSKI STANDARD
oSIST prEN 12186:2013
01-julij-2013
Infrastruktura za plin - Plinske postaje za regulacijo tlaka za prenos in distribucijo -
Funkcionalne zahteve
Gas infrastructure - Gas pressure regulating stations for transmission and distribution -
Functional requirements
Gasinfrastruktur - Gas-Druckregelanlagen für Transport und Verteilung - Funktionale
Anforderungen
Infrastructures gazières - Postes de détente régulation de pression de gaz pour le
transport et la distribution - Prescriptions fonctionnelles
Ta slovenski standard je istoveten z: prEN 12186
ICS:
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
75.200 2SUHPD]DVNODGLãþHQMH Petroleum products and
QDIWHQDIWQLKSURL]YRGRYLQ natural gas handling
]HPHOMVNHJDSOLQD equipment
oSIST prEN 12186:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12186:2013

---------------------- Page: 2 ----------------------
oSIST prEN 12186:2013


EUROPEAN STANDARD
DRAFT
prEN 12186
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2013
ICS 75.200; 27.060.20; 23.060.40 Will supersede EN 12186:2000
English Version
Gas infrastructure - Gas pressure regulating stations for
transmission and distribution - Functional requirements
Infrastructures gazières - Postes de détente régulation de Gasinfrastruktur - Gas-Druckregelanlagen für Transport
pression de gaz pour le transport et la distribution - und Verteilung - Funktionale Anforderungen
Prescriptions fonctionnelles
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 234.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12186:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12186:2013
prEN 12186:2013 (E)
Contents Page
Foreword .4
1 Scope .5
2 Normative references .6
3 Terms, definitions, symbols and abbreviations .6
3.1 General .6
3.2 Station .7
3.3 Pressure, design and testing .9
3.4 Pressure control . 10
3.5 Continuity of supply . 11
4 Quality and management system .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.