FprEN 6101
(Main)Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application.
Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-Reihe
No Scope available
Série aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inches
Le présent document spécifie les dimensions, les tolérances et la masse des rivets de précision à tête fraisée moyenne 100°, série en inches, pour les applications aérospatiales.
Aeronavtika - Kovice, 100° srednje ugrezna glava, ozka toleranca - Palčne mere
General Information
RELATIONS
Standards Content (sample)
SLOVENSKI STANDARD
oSIST prEN 6101:2019
01-januar-2019
$HURQDYWLND.RYLFHƒVUHGQMHSRJOREOMHQDJODYDR]NDWROHUDQFD3DOþQHPHUH
Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch seriesLuft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inches
Ta slovenski standard je istoveten z: prEN 6101ICS:
49.030.60 Kovice Rivets
oSIST prEN 6101:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN 6101:2019
---------------------- Page: 2 ----------------------
oSIST prEN 6101:2019
DRAFT
EUROPEAN STANDARD
prEN 6101
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2018
ICS 49.030.60 Will supersede EN 6101:2016
English Version
Aerospace series - Rivet, 100° medium flush head, close
tolerance - Inch series
Série aérospatiale - Rivets de précision, tête fraisée Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf,
moyenne 100° - Série en inches enge Toleranz - Zoll-ReiheThis draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 6101:2018 E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
oSIST prEN 6101:2019
prEN 6101:2018 (E)
Contents Page
European foreword ....................................................................................................................................................... 3
Introduction .................................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 6
4 Requirements ................................................................................................................................................... 6
4.1 Configuration, dimensions, tolerances and mass ................................................................................ 6
4.2 Material and surface treatment .............................................................................................................. 11
5 Designation..................................................................................................................................................... 13
6 Marking ............................................................................................................................................................ 13
6.1 Material identification ............................................................................................................................... 13
6.2 Manufacturer's identification .................................................................................................................. 14
6.3 Identification of oversize rivets .............................................................................................................. 14
7 Technical specification ............................................................................................................................... 15
7.1 Aluminium alloy rivet ................................................................................................................................. 15
7.2 Titanium alloy rivet ..................................................................................................................................... 15
7.3 Heat resisting alloy NI-P9001 (NiCu31) rivets .................................................................................. 15
8 Quality management system .................................................................................................................... 15
Annex A (informative) Record of revision .......................................................................................................... 16
Bibliography ................................................................................................................................................................. 17
---------------------- Page: 4 ----------------------oSIST prEN 6101:2019
prEN 6101:2018 (E)
European foreword
This document (prEN 6101:2018) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.This document is currently submitted to the CEN Enquiry.
This document will supersede EN 6101:2016.
---------------------- Page: 5 ----------------------
oSIST prEN 6101:2019
prEN 6101:2018 (E)
Introduction
This document is published at Airbus agreed version prEN 6101 edition P3. Former issue 1 and 2 and
drafts may exist of Airbus development only but without any ASD–STAN official publication. In
consequence configuration management discrepancies with these unofficial documents are under
Airbus responsibility.---------------------- Page: 6 ----------------------
oSIST prEN 6101:2019
prEN 6101:2018 (E)
1 Scope
This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head,
close tolerance, inch series, for aerospace application.2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
FprEN 2114, Aerospace series - Aluminium 1050A-H14 - Wire for solid rivets – D ≤ 10 mm
EN 2115, Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets – D ≤ 10 mm
EN 2116, Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets – D ≤ 10 mm
EN 2117, Aerospace series - Aluminium alloy AL-P5056A (5056A)-H32 - Wire for solid rivets – D ≤ 10 mm
EN 2424, Aerospace series - Marking of aerospace productsEN 2941, Aerospace series - Nickel alloy rivets - Technical specification
EN 3115, Aerospace series - Aluminium alloy 7050-T73 - Wire for solid rivets – D ≤ 10 mm
EN 4372, Aerospace series - Heat resisting nickel alloy with copper NI-PD9001 (NiCu31) - Wire for solid
rivets - D ≤ 10 mmprEN 6104, Aerospace series - Rivets, solid, in aluminium or aluminium alloy - Inch series - Technical
SpecificationprEN 6118, Aerospace series - Process specification - Aluminium base protection for fasteners
ISO 8080, Aerospace - Anodic treatment of titanium and titanium alloys - Sulfuric acid process
AMS 4982, Titanium alloy wire 44.5 CbAMS-QQ-P-416, Plating, cadmium (electrodeposited)
MIL-A-8625, Anodic coatings for aluminum and aluminum alloys
MIL-C-5541, Chemical conversion coatings on aluminium and aluminium alloys
NAS 9800, Head protrusion gaging, 100° flush head fasteners, gage block, gage diameters and stylus
Under preparation. Published as ASD Prestandard at the date of publication of this standard.
Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA.
Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA.
Published by: Aerospace Industries Association of America, Inc. (AIA), 1250 Eye Street, N.W., Washington, D.C.
20005-3924, USA.---------------------- Page: 7 ----------------------
oSIST prEN 6101:2019
prEN 6101:2018 (E)
NASM 5674, Rivets, structural, aluminium alloy, titanium columbium alloy, general specification for
3 Terms and definitionsNo terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.