EN ISO 8028:2024
(Main)Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:2024)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:2024)
This document specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
Gummi- und/oder Kunststoffschläuche und ‑schlauchleitungen für das luftfreie Farbspritzen - Spezifikation (ISO 8028:2024)
Dieses Dokument legt die Anforderungen an vier Typen von Schläuchen und Schlauchleitungen für die Verwendung beim luftfreien Farbspritzen fest. Die vier Typen werden nach Berstdruck und Betriebstemperatur unterschieden, und können aus Gummi oder Kunststoffmaterialien oder einer Kombination aus Gummi und Kunststoff hergestellt sein.
WARNUNG — Die in diesem Dokument beschriebene Prüfung sollte von erfahrenem Personal durchgeführt werden. In diesem Dokument werden nicht alle Sicherheitsprobleme behandelt, die bei Anwendung der Norm auftreten können. Der Anwender ist für die Einführung geeigneter Maßnahmen zur Einhaltung der Anforderungen an Sicherheit und Gesundheit verantwortlich.
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des peintures - Spécifications (ISO 8028:2024)
Le présent document spécifie les exigences relatives à quatre types de tuyaux et flexibles utilisés dans la pulvérisation des peintures sans air. Les quatre types sont différenciés par la pression de rupture et la température d’utilisation, et peuvent être réalisés à partir de matériaux en caoutchouc ou en plastique, ou une combinaison de matériaux en caoutchouc et en plastique.
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve - Specifikacija (ISO 8028:2024)
Standard ISO 8028:2017 določa zahteve za štiri vrste cevi in cevnih priključkov za brezzračno brizganje barve. Te štiri vrste se ločujejo glede na razpočni tlak in delovno temperaturo, mogoče pa jih je izdelati iz gumenih ali polimernih materialov ali s kombiniranjem teh dveh vrst materialov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve -
Specifikacija (ISO 8028:2024)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying -
Specification (ISO 8028:2024)
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie
Farbspritzen - Spezifikation (ISO 8028:2024)
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation (AIRLESS) des
peintures - Spécifications (ISO 8028:2024)
Ta slovenski standard je istoveten z: EN ISO 8028:2024
ICS:
83.140.40 Gumene cevi Hoses
87.100 Oprema za nanašanje Paint coating equipment
premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8028
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 83.140.40; 87.100 Supersedes EN ISO 8028:2018
English Version
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying - Specification (ISO 8028:2024)
Tuyaux et flexibles en caoutchouc et/ou en plastique Gummi- und/oder Kunststoffschläuche und -
pour pulvérisation (AIRLESS) des peintures - schlauchleitungen für das luftfreie Farbspritzen -
Spécifications (ISO 8028:2024) Spezifikation (ISO 8028:2024)
This European Standard was approved by CEN on 9 August 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8028:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 8028:2024) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards
shall be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8028:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8028:2024 has been approved by CEN as EN ISO 8028:2024 without any modification.
International
Standard
ISO 8028
Fourth edition
Rubber and/or plastics hoses and
2024-07
hose assemblies for airless paint
spraying — Specification
Tuyaux et flexibles en caoutchouc et/ou en plastique pour
pulvérisation (AIRLESS) des peintures — Spécifications
Reference number
ISO 8028:2024(en) © ISO 2024
ISO 8028:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8028:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types of hose and hose assemblies . 1
5 Construction and materials . 2
6 Dimensions and tolerances . 2
7 Performance requirements for finished hose . 2
7.1 Adhesion requirements .2
7.2 Ultraviolet resistance (plastics cover only) .3
7.3 Resistance to ozone (rubber cover only) .3
8 Performance requirements for finished hose and hose assemblies . 3
8.1 Hydrostatic requirements .3
8.2 Impulse test requirements .3
8.3 Electrical-continuity requirements .3
9 Physical requirements of lining for hose only . 3
10 Frequency of testing . . 4
11 Test report . 4
12 Marking . . 4
13 Recommendations for packaging and storage . 5
Annex A (normative) Test frequency for type tests and routine tests . 6
Bibliography . 7
iii
ISO 8028:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 218, Rubber and plastics hoses and hose assemblies, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 8028:2017), which has been technically
revised.
The main changes are as follows:
— subclause 8.1 and Table A.2 (merged with Table A.1) have been re-written to clarify the conditions for the
number of test samples;
— subclause 8.2 has been re-written to make appropriate minimum bend radius and to confirm the
Electrical-continuity requirements after the impulse test;
— subclause 8.3 has been re-written to cite appropriate subclauses in ISO 8031;
— in Clause 12, year of publication has been deleted, and the unit of working pressure to MPa as a main unit
has been changed;
— Annex B has been deleted;
— the Normative references have been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 8028:2024(en)
Rubber and/or plastics hoses and hose assemblies for airless
paint spraying — Specification
WARNING — Persons using this document should be familiar with normal laboratory practice. This
document does not purport to address all of the safety problems, if any, associated with its use. It is
the responsibility of the user to establish appropriate safety and health practices.
1 Scope
This document specifies the requir
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.