EN ISO 11296-9:2022
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system.
NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 9: Lining mit einer fest verankerten Kunststoffauskleidung (ISO 11296-9:2022)
Dieses Dokument legt in Verbindung mit ISO 11296 1 die Anforderungen und Prüfverfahren für Rohre und Formstücke fest, die für die Renovierung erdverlegter druckloser Entwässerungsnetze (Freispiegelleitungen) durch Lining mit einem einzelnen biegesteifen Ringraum aus einem tragenden zementhaltigen Mörtel hinter einer Kunststoffauskleidung verwendet werden. Diese Kunststoffauskleidung dient als Dauerform, die mit dem Mörtel verankert ist.
Dieses Dokument ist anwendbar für Kunststoffauskleidungen und Mörtelsysteme mit oder ohne Stahlbewehrung. Es behandelt nicht die statische Auslegung des Lining-Systems.
ANMERKUNG Es gibt Systeme mit mehreren Ringräumen, die jedoch durch Patentrechte geschützt sind und in diesem Dokument nicht behandelt werden.
Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 9: Tubage par coffrage plastique interne rigidement ancré (ISO 11296-9:2022)
Le présent document, conjointement avec l’ISO 11296‑1, spécifie les exigences et les méthodes d’essai pour les tuyaux et raccords pour la rénovation des réseaux de branchements et de collecteurs d’assainissement enterrés sans pression par tubage avec un simple espace annulaire en coulis de ciment structurel formé derrière un coffrage plastique interne. Ce coffrage plastique sert de moule permanent ancré au coulis.
Le présent document est applicable aux coffrages plastiques internes et aux systèmes de coulis avec ou sans armature en acier. Il ne s’applique pas à la conception structurelle du système de tubage.
NOTE Il existe des systèmes ayant plusieurs espaces annulaires, mais ils sont soumis à des droits de propriété industrielle et ne sont pas abordés par le présent document.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 9. del: Oblaganje s trdno zasidrano notranjo plastjo iz plastike (ISO 11296-9:2022)
Ta dokument skupaj s standardom EN ISO 11296-1 določa zahteve in preskusne metode za cevi ter spojnike za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) z oblaganjem s trdno zasidranim vmesnim prostorom strukturne cementne injekcijske mase za notranjo plastjo iz plastike. Ta plast iz plastike se uporablja kot stalni opaž, ki je pritrjen na maso.
Uporablja se za notranje obloge iz plastike in sisteme za nanašanje malte z jekleno armaturo ali brez nje.
Ne uporablja se za projektiranje konstrukcij sistema oblog.
OPOMBA: Sistemi z več vmesnimi prostori so na voljo, vendar so nadzorovani s patentnimi pravicami in niso vključeni v tem standardu.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2023
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 9.
del: Oblaganje s trdno zasidrano notranjo plastjo iz plastike (ISO 11296-9:2022)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO
11296-9:2022)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 9: Lining mit einer fest verankerten
Kunststoffauskleidung (ISO 11296-9:2022)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 9:
Tubage par coffrage plastique interne rigidement ancré (ISO 11296-9:2022)
Ta slovenski standard je istoveten z: EN ISO 11296-9:2022
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11296-9
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030
English Version
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 9:
Lining with a rigidly anchored plastics inner layer (ISO
11296-9:2022)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux de branchements et de von erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 9: Lining mit einer fest
Partie 9: Tubage par coffrage plastique interne verankerten Kunststoffauskleidung (ISO 11296-
rigidement ancré (ISO 11296-9:2022) 9:2022)
This European Standard was approved by CEN on 27 May 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-9:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11296-9:2022) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 165 “Waste water engineering” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 11296-9:2022 has been approved by CEN as EN ISO 11296-9:2022 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-9
First edition
2022-09
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 9:
Lining with a rigidly anchored plastics
inner layer
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 9: Tubage par coffrage plastique interne rigidement ancré
Reference number
ISO 11296-9:2022(E)
ISO 11296-9:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 11296-9:2022(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Symbols and abbreviated terms.4
4.1 General . 4
4.2 Symbols . 4
4.3 Abbreviated terms . 5
5 Pipes at the “M” stage . 5
5.1 Materials . 5
5.1.1 Product variants . 5
5.1.2 Components of RAPL . 6
5.2 General characteristics . 7
5.3 Material characteristics . 7
5.3.1 Material characteristics of studded PE sheet and PE profiled plastics strip . 7
5.3.2 Material characteristics of PVC-U profiled plastics strips . 8
5.3.3 Material characteristics of seam sealant . 8
5.3.4 Material characteristics of the grout system . 8
5.4 Geometric characteristics . 10
5.4.1 General . 10
5.4.2 Studded PE sheet . 10
5.4.3 Profiled plastics strips . 10
5.5 Mechanical characteristics . 11
5.6 Physical characteristics . 11
5.7 Jointing.12
5.7.1 General .12
5.7.2 Welding of studded PE sheet to form it into tube .12
5.7.3 Mechanical jointing of spirally wound PVC-U plastics profiled strips .13
5.7.4 Mechanical jointing of PE plastics profile strips . 14
5.8 Marking . 14
5.8.1 Marking of plastics inner layers . 14
5.8.2 Marking of packaged or bulk containerised grout . 14
5.9 Regional requirements for pipes . 15
6 Fittings at the “M” stage .15
6.1 General . 15
6.2 Materials . 15
6.3 Geometric characteristics .15
7 Ancillary components .16
8 Fitness for purpose of the installed lining system at the “I” stage .16
8.1 Materials . 16
8.2 General ch
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.