EN 1434-6:2015+A1:2019

Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance

This European Standard specifies commissioning, operational monitoring and maintenance and applies to thermal energy meters. Thermal energy meters are instruments intended for measuring the energy which in a heat-exchange circuit is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The thermal energy meter indicates the quantity of heat in legal units.
Electrical safety requirements are not covered by this European Standard.
Pressure safety requirements are not covered by this European Standard.
Surface mounted temperature sensors are not covered by this European Standard.
This standard covers meters for closed systems only, where the differential pressure over the thermal load is limited.

Thermische Energiemessgeräte - Teil 6: Einbau, Inbetriebnahme, Überwachung und Wartung

Diese Europäische Norm gilt für !thermische Energiemessgeräte" und legt die Inbetriebnahme, die Überwachung und die Wartung von diesen fest. !Thermische Energiemessgeräte" sind Geräte, die dazu dienen, die Energiemenge zu messen, die in einem Wärmeübertragerkreislauf durch eine als Wärmeträgerflüssigkeit bezeichnete Flüssigkeit aufgenommen (Kühlen) oder abgegeben (Heizen) wird. Das !thermische Energiemessgerät" zeigt die Wärmemenge in gesetzlichen Einheiten an.
Elektrische Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Den Druck betreffende Sicherheitsanforderungen werden in dieser Europäischen Norm nicht behandelt.
Oberflächenmontierte Temperaturfühler werden in dieser Europäischen Norm nicht behandelt.
Die vorliegende Norm behandelt ausschließlich Zähler für geschlossene Systeme, in denen der Differenz-druck über die Wärmemenge begrenzt ist.

Compteurs d'énergie thermique - Partie 6 : Installation, mise en service, surveillance et maintenance

La présente Norme européenne spécifie l'installation, la mise en service, à la surveillance de fonctionnement et la maintenance et s'applique aux compteurs d'énergie thermique. Les compteurs d'énergie thermique sont des instruments destinés à mesurer l'énergie thermique qui, dans un circuit d'échange thermique, est absorbée (refroidissement) ou cédée (chauffage) par un liquide appelé
« liquide caloporteur ». Le compteur d'énergie thermique fournit la quantité d'énergie thermique en unités de mesure légales.
La présente Norme européenne ne traite pas des prescriptions de sécurité électrique.
La présente Norme européenne ne traite pas des prescriptions de sécurité relative à la pression.
La présente Norme européenne ne traite pas des sondes de température montées en surface.
La présente norme couvre les compteurs pour les systèmes fermés uniquement, où la pression différentielle dans la charge thermique est limitée.

Merilniki toplote - 6. del: Vgradnja, zagon, nadzor in vzdrževanje (vključno z dopolnilom A1)

Ta evropski standard določa zagon, nadzor delovanja in vzdrževanje ter se uporablja za merilnike toplotne energije. Merilniki toplote so instrumenti, namenjeni merjenju energije, ki jo v krogotoku toplotne izmenjave absorbira (hlajenje) ali oddaja (ogrevanje) tekočina, imenovana tekočina za prenos toplote. Merilnik toplote podaja toploto v predpisanih enotah.
Ta evropski standard ne zajema električnih varnostnih zahtev.
Ta evropski standard ne zajema tlačnih varnostnih zahtev.
Ta evropski standard ne zajema površinsko nameščenih senzorjev temperature.
Ta standard zajema samo števce za zaprte sisteme, kjer je diferencialni tlak nad toplotno obremenitvijo omejen.

General Information

• Status: Withdrawn
• Publication Date: 12-Feb-2019
• Withdrawal Date: 06-Sep-2022
• ICS: 17.200.10 - Heat. Calorimetry
• Technical Committee: CEN/TC 176 - Heat meters
• Drafting Committee: CEN/TC 176/WG 2 - Heat Meters - Requirements, test methods and technical editing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 07-Sep-2022
• Directive: 2014/32/EU - Directive 2014/32/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of measuring instruments
• Mandate: M/441 - Standardisation mandate to CEN, CENELEC and ETSI in the field of measuring instruments for the development of an open architecture for utility meters involving communication protocols enabling interoperability
• Mandate: M/541 - [C(2015)8558] Standardization request in support of the implementation of Directive 2014/32/EU on measuring instruments
• Ref Project: SIST EN 1434-6:2016+A1:2019 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance

Relations

• Merged From: EN 1434-6:2015 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 19-Jan-2023
• Merged From: EN 1434-6:2015/prA1 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 20-Jun-2018
• Replaced By: EN 1434-6:2022 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
• Effective Date: 14-Sep-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Thermische Energiemessgeräte - Teil 6: Einbau, Inbetriebnahme, Überwachung und WartungCompteurs d'énergie thermique - Partie 6 : Installation, mise en service, surveillance et maintenanceThermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance17.200.10Toplota. KalorimetrijaHeat. CalorimetryICS:Ta slovenski standard je istoveten z:EN 1434-6:2015+A1:2019SIST EN 1434-6:2016+A1:2019en,fr,de01-april-2019SIST EN 1434-6:2016+A1:2019SLOVENSKI
STANDARDSIST EN 1434-6:20161DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1434-6:2015+A1
February
t r s { ICS
s yä t r rä s r Supersedes EN
s v u væ xã t r s wEnglish Version
Thermal energy meters æ Part
xã Installationá commissioningá operational monitoring and maintenanceCompteurs d 5énergie thermique æ Partie
x ã Installationá mise en serviceá surveillance et maintenance
Thermische Energiemessgeräte æ Teil
xã Einbauá Inbetriebnahmeá Überwachung und Wartung This European Standard was approved by CEN on
w September
t r s w and includes Amendment
s approved by CEN on
w February
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s { CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u væ xã t r s w ªA sã t r s { ESIST EN 1434-6:2016+A1:2019

!Thermal energy meter" installation . 8 Annex B (informative)
!Thermal energy meter" operational monitoring and maintenance. 18 Annex C (informative)
Suggested gauge for checking the dimensions of installed temperature sensor pockets . 21 Annex ZA (informative)
Relationship between this European Standard and the essential requirements of Directive 2014/32/EU aimed to be covered . 22 Bibliography . 23
This document supersedes !EN 1434-6:2015". The start and finish of text introduced or altered by amendment is indicated in the text by tags !". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. EN 1434, Thermal energy meters consists of the following parts: — Part 1: General requirements — Part 2: Constructional requirements — Part 3: Data exchange and interfaces1) — Part 4: Pattern approval tests — Part 5: Initial verification tests — Part 6: Installation, commissioning, operational monitoring and maintenance In comparison to EN 1434-6:2007, the following changes have been made: — special cases for combined !thermal energy meters" are added; — additional functionalities for smart metering applications are added; — installation requirements added for !thermal energy meters" which are located next to cables like data communication cables and mains supply cables; — installation requirement changed for 4-wire connections; — cooling meters are added. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
1) EN 1434-3 is maintained by CEN/TC 294.
system to the thermal energy mains 3.4 primary circuit circuit hydraulically connected to the thermal energy mains" 3.5 secondary circuit circuit hydraulically separated from the primary circuit SIST EN 1434-6:2016+A1:2019

3 5 10 20 30 40 50 60 0,5 0,2 0,2 0,1 0,1 0,1 0 0 0 1 0,5 0,4 0,3 0,2 0,1 0,1 0,1 0,1 2 0,9 0,7 0,5 0,3 0,2 0,2 0,1 0,1 3 1,4 1,1 0,8 0,5 0,3 0,2 0,2 0,2 4 1,8 1,5 1,0 0,6 0,4 0,3 0,3 0,2 5 2,3 1,9 1,3 0,8 0,5 0,4 0,3 0,3 6 2,7 2,2 1,5 0,9 0,6 0,5 0,4 0,3 7 3,2 2,6 1,9 1,1 0,7 0,6 0,5 0,4 8 3,6 3,0 2,0 1,2 0,9 0,7 0,5 0,4 9 4,1 3,3 2,3 1,4 1,0 0,7 0,6 0,5 10 4,5 4,0 2,5 1,5 1,1 0,8 0,7 0,5 The values are shown as fraction of the maximum permissible error for the calculator. The values below the marked line are higher than 1/3rd of the maximum permissible error for the heat calculator. If the resulting error is higher than 1/3rd of the maximum permissible error, it is recommended to change the installation to have smaller differential pressure. NOTE In cases where flows from two different loads with different temperatures (e.g. for space heating and domestic warm water) are merged together just before the temperature sensor, the optimum position for the sensor is after the flow sensor. SIST EN 1434-6:2016+A1:2019
...