Aerospace series - Designation of metallic semi-finished products - Rules

This document specifies the designation rules for metallic semi-finished products given in Table 1, used in aerospace construction.
It is applicable only if referred to in the metallic semi-finished product standard.

Luft- und Raumfahrt - Bezeichnung von metallischen Halbzeugen - Regeln

Série aérospatiale - Désignation des demi-produits métalliques - Règles

Aeronavtika - Označevanje kovinskih polizdelkov - Pravila

Ta dokument določa pravila za označevanje kovinskih polizdelkov iz tabele 1, ki se uporabljajo pri aeronavtiki.
Uporablja se le, če je naveden v standardu kovinskih polizdelkov.

General Information

Status
Published
Publication Date
18-Dec-2018
Withdrawal Date
29-Jun-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
19-Dec-2018
Completion Date
19-Dec-2018

Buy Standard

Standard
EN 2600:2019
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Bezeichnung von metallischen Halbzeugen - RegelnSérie aérospatiale - Désignation des demi-produits métalliques - RèglesAerospace series - Designation of metallic semi-finished products - Rules49.025.05Železove zlitine na splošnoFerrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2600:2018SIST EN 2600:2019en,fr,de01-marec-2019SIST EN 2600:2019SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2600
December
t r s z ICS
English Version
Aerospace series æ Designation of metallic semiæfinished products æ Rules Série aérospatiale æ Désignation des demiæproduits métalliques æ Règles
Luftæ und Raumfahrt æ Bezeichnung von metallischen Halbzeugen æ Regeln This European Standard was approved by CEN on
s y September
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t x r rã t r s z ESIST EN 2600:2019

Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Designation scheme . 4 Annex A (normative)
Codes for metallic semi-finished product standards . 7 Annex B (normative)
Codes for thickness, diameter, across-flats, width, length . 8 Annex C (normative)
Codes for cross-section dimensions of sections . 12 C.1 Beaded L-section, extruded . 12 C.2 L-section, extruded . 13 C.3 Chanel section, extruded . 14 C.4 T-section, extruded . 15 C.5 L-section, folded profiles . 16 C.6 L-section, folded profiles with internally lipped flanges . 17 C.7 U-section, folded profiles . 18 C.8 U-section, folded profiles with externally lipped flanges . 19 C.9 U-section, folded profiles with internally lipped flanges . 20 C.10 Z-section, folded profiles . 21 C.11 Z-section, folded profiles with one lipped flange . 22 C.12 Z-section, folded profiles with lipped flanges . 23 C.13 Top-hat section, folded profiles . 24 C.14 Bowler-hat section, folded profiles . 25 C.15 Top-hat section, folded profiles with lipped flanges . 26 Annex D (normative)
Identity block examples . 27
EN 2032-2, Aerospace series — Metallic materials — Part 2: Coding of metallurgical condition in delivery condition 3 Designation scheme The designation of a metallic semi-finished product is made up according to the directives in force. Among those directives concerning the description block, the originator code and the identity block, only the latter requires additional data. This data concerns the two components of the identity block: the “European standard block” and the “Particular product block”. Examples of the identity block are given in Annex D. 3.1 European standard block The European standard block consists of the material standard number. 3.2 Particular product block This particular product block consists, in sequence, of the following: 3.2.1 The delivery heat treatment condition code of the semi-finished product This alphabetical code (one character) defined in EN 2032-2 is called-up in the material standards. 3.2.2 The semi-finished product standard code This numerical code (two characters) is called-up in:  Annex A;  each semi-finished product standard;  the corresponding material standards. 3.2.3 Data concerning dimensions Depending on the use of the identity block, this data is either partial (method A) or complete (method B). SIST EN 2600:2019

Millimetres are systematically to be preceded by a hyphen (–).  the sequence of the codes for cross-sections, requiring more than one dimension, shall be indicated. Table 1 Semi-finished products Dimensions Thickness Diameter Across-flats Width Cross-section Sheet mm — — — — Plate Strip Foil Round bar — mm — — — Wire Square bar mm — — — — Hexagonal bar — — mm — — Rectangular bar 1 code* — 2 code* — — Round tube 2 code* 2 code* — — — Section — — — — code** * See Annex B. ** See Annex C.
3.2.3.2 Method B All dimensions of a semi-finished product are given in codes according to the sequence of Table 2.
Codes for metallic semi-finished product standards Table A.1 — European standards and related codes Semi-finished products Codes Semi-finished products Codes Semi-finished products Codes EN 2033 01 EN 2338 34 — 67 EN 2034 02 EN 2339 35 — 68 EN 2035 03 EN 2340 36 — 69 EN 2036 04 EN 2341 37 — 70 EN 2037 05 EN 2366 38 — 71 EN 2038 06 EN 2368 39 — 72 EN 2039 07 EN 2369 40 — 73 EN 2040 08 EN 2589 41 — 74 EN 2041 09 EN 2590 42 — 75 EN 2042 10 EN 2599 43 — 76 EN 2044 11 EN 2615 44 — 77 EN 2045 12 EN 2616 45 — 78 EN 2046 13 EN 2617 46 — 79 EN 2047 14 EN 2621 47 — 80 EN 2048 15 EN 2622 48 — 81 EN 2049 16 EN 3145 49 — 82 EN 2050 17 EN 3146 50 — 83 EN 2051 18 — 51 — 84 EN 2052 19 — 52 — 85 EN 2053 20 — 53 — 86 EN 2054 21 — 54 — 87 EN 2055 22 — 55 — 88 EN 2056 23 — 56 — 89 EN 2057 24 — 57 — 90 EN 2058 25 — 58 — 91 EN 2059 26 — 59 — 92 EN 2060 27 — 62 — 93 EN 2061 28 — 61 — 94 EN 2071 29 — 62 — 95 EN 2131 30 — 63 — 96 EN 2134 31 — 64 — 97 EN 2257 32 — 65 — 98 EN 2258 33 — 66 — 99 SIST EN 2600:2019

Codes for thickness, diameter, across-flats, width, length Table B.1 — Dimensions and related codes (1 of 4) Dimensions in millimetres Dimensions Codes Dimensions Codes Dimensions Codes Dimensions Codes 0,1 AA 5,4 CH 17 EQ 70 GY 0,2 AB 5,5 CJ 18 ER 71 GZ 0,3 AC 5,6 CK 19 ES 72 HA 0,4 AD 5,7 CL 20 ET 73 HB 0,5 AE 5,8 CM 21 EU 74 HC 0,6 AF 5,9 CN 22 EV 75 HD 0,7 AG 6,0 CP 23 EW 76 HE 0,8 AH 6,1 CQ 24 EY 77 HF 0,9 AJ 6,2 CR 25 EZ 78 HG 1,0 AK 6,3 CS 26 FA 79 HH 1,1 AL 6,4 CT 27 FB 80 HJ 1,2 AM 6,5 CU 28 FC 81 HK 1,3 AN 6,6 CV 29 FD 82 HL 1,4 AP 6,7 CW 30 FE 83 HM 1,5 AQ 6,8 CY 31 FF 84 HN 1,6 AR 6,9 CZ 32 FG 85 HP 1,7 AS 7,0 DA 33 FH 86 HQ 1,8 AT 7,1 DB 34 FJ 87 HR 1,9 AU 7,2 DC 35 FK 88 HS 2,0 AV 7,3 DD 36 FL 89 HT 2,1 AW 7,4 DE 37 FM 90 HU 2,2 AY 7,5 DF 38 FN 91 HV 2,3 AZ 7,6 DG 39 FP 92 HW 2,4 BA 7,7 DH 40 FQ 93 HY 2,5 BB 7,8 DJ 41 FR 94 HZ
9,7 EE 60 GM 165 JU 4,5 BY
9,8 EF 61 GN 170 JV 4,6 BZ 9,9 EG 62 GP 175 JW 4,7 CA 10 EH 63 GQ 180 JY 4,8 CB 11 EJ 64 GR 185 JZ 4,9 CC 12 EK 65 GS 190 KA 5,0 CD 13 EL 66 GT 195 KB 5,1 CE 14 EM 67 GU 200 KC 5,2 CF 15 EN 68 GV 210 KD 5,3 CG 16 EP 69 GW 220 KE
SN 240 KG 1 250 MS 11 000 QD 67 000 SP 250 KH 1 300 MT 12 000 QE 68 000 SQ 260 KJ 1 350 MU 13 000 QF 69 000 SR 270 KK 1 400 MV 14 000 QG 70 000 SS 280 KL 1 450
MW 15 000 QH 71 000 ST 290 KM 1 500 MY 16 000 QJ 72 000 SU 300 KN 1 550 MZ 17 000 QK 73 000 SV 310 KP 1 600 NA 18 000 QL 74 000 SW 320 KQ 1 650 NB 19 000 QM 75 000 SY 330 KR 1 700 NC 20 000 QN 76 000 SZ 340 KS 1 750 ND 21 000 QP 77 000 TA 350 KT 1 800 NE 22 000 QQ 78 000 TB 360 KU 1 850
NF 23 000 QR 79 000 TC 370 KV 1 900 NG 24 000 QS 80 000 TD 380 KW 1 950
NH 25 000 QT 81 000 TE 390 KY 2 000 NJ 26 000 QU 82 000 TF 400 KZ 2 100 NK 27 000 QV 83 000 TG 410 LA 2 200 NL 28 000 QW 84 000 TH 420 LB 2 300 NM 29 000 QY 85 000 TJ 430 LC 2 400 NN 30 000 QZ 86 000 TK 440 LD 2 500 NP 31 000 RA 87 000 TL 450 LE 2 600 NQ 32 000 RB 88 000 TM 460 LF 2 700 NR 33 000 RC 89 000 TN 470 LG 2 800
NS 34 000 RD 90 000 TP 480 LH 2 900 NT 35 000 RE 91 000 TQ 490 LJ 3 000 NU 36 000 RF 92 000 TR 500 LK 3 100 NV 37 000 RG 93 000 TS 520 LL 3 200 NW 38 000 RH 94 000 TT 540 LM 3 300 NY 39 000 RJ 95 000 TU 560 LN 3 400 NZ 40 000 RK 96 000 TV 580 LP 3 500 PA 41 000 RL 97 000 TW SIST EN 2600:2019

RZ — — 840 MD 4 800 PP 54 000 SA — — 860 ME 4 900 PQ 55 000 SB — — 880 MF 5 000 PR 56 000 SC — — 900 MG 5 500 PS 57 000
SD — — 920 MH 6 000 PT 58 000 SE — — 940 MJ 6 500 PU 59 000
SF — — 960 MK
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.