Road vehicles - Rechargeable batteries with internal energy storage - Performance of alkali-Ion (Li-Ion, Na-Ion), Pb, NiMH and combined chemistries EV modules and batteries

The standard shall describe the necessary steps and conditions for the measurement of the parameters, which are relevant for rechargeable batteries with internal energy storage used for road vehicles. The parameters shall reflect current industry practice for the applications based on existing international standards. The standard shall consider the most appropriate metric based on application and the objective of the metric to enable comparison of electrical performance between different models/products on the market. It shall in particular take into account the following:
- rated capacity (in Ah);
- rated power (in W);
- internal resistance (in ꭥ);
- energy round trip efficiency (in %).
The measurement tests of the standard shall be relevant for batteries, battery packs, and battery modules intended for the following applications:
- motor vehicles, including M and N categories referred to in Article 2 of Regulation (EU) 2018/858 of the European Parliament and of the Council with traction battery;
- L-category vehicles referred to in Article 2 of Regulation EU 168/2013 of the European Parliament and of the Council with traction battery of more than 25kg.

Straßenfahrzeuge - Wiederaufladbare Batterien mit internem Speicher - Unmittelbare Leistung von Modulen und Batterien für Elektrofahrzeuge mit Li-Ion, Pb, NiMH und kombinierter Chemie

Véhicules routiers - Batteries rechargeables avec stockage interne d'énergie - Performance des modules et batteries alcali-ion (Li-Ion, Na-Ion), Pb, NiMH et chimies combinées pour véhicules électriques

Le présent document décrit les procédures d'essai de performance et les méthodes de calcul pour les systèmes de batteries, les assemblages-batteries et les modules de batterie de VE de composition chimique métaux alcalins-ion (par exemple, Li-ion, Na-ion), Pb, NiMH et combinée. Le présent document prend en compte le paramètre le plus approprié, en fonction de l'application des performances électriques entre différents modèles/produits sur le marché. Il spécifie les procédures d'essai de performance et les méthodes de calcul permettant d'obtenir des valeurs de performance pour :
•   la capacité nominale (en Ah) ;
•   la puissance (en W) ;
•   la résistance interne (en ꭥ) ;
•   le rendement énergétique aller-retour (en %) ;
•   la durée de vie attendue (nombre de cycles de référence).
Les essais présentés dans le présent document sont pertinents pour les systèmes de batteries, les assemblages-batteries et les modules de batterie des VE destinés aux applications suivantes :
•   les véhicules à moteur, y compris les véhicules de catégories M, N et O visés à l'Article 2 du règlement (UE) 2018/858 du Parlement européen et du Conseil avec une batterie de traction ;
•   les véhicules de catégorie L visés à l'Article 2 du règlement (UE) 168/2013 du Parlement européen et du Conseil avec une batterie de traction de plus de 25 kg.
NOTE 1   D'autres compositions chimiques peuvent être incluses dans le domaine d'application du présent document.
NOTE 2   Ces procédures peuvent être utilisées pour l'essai de type d'un modèle/produit au début de sa durée de vie (statut « d'origine ») et pour l'essai individuel de la batterie après un changement de statut (statut « réutilisée » et « remanufacturée »).
Les essais applicables aux paramètres ci-dessus sont effectués au niveau des composants à l'extérieur du véhicule.

Cestna vozila - Polnilne baterije z notranjim shranjevanjem energije - Delovanje alkalno-ionskih (Li-Ion, Na-Ion), Pb, NiMH in kombiniranih kemikalij Moduli in baterije za električna vozila

General Information

Status
Not Published
Publication Date
01-May-2025
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
13-Jun-2024
Due Date
08-Mar-2024
Completion Date
13-Jun-2024

Buy Standard

Draft
prEN 18060:2024 - BARVE
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2024
Cestna vozila - Polnilne baterije z notranjim shranjevanjem energije - Delovanje
alkalno-ionskih (Li-Ion, Na-Ion), Pb, NiMH in kombiniranih kemikalij Moduli in
baterije za električna vozila
Road vehicles - Rechargeable batteries with internal energy storage - Performance of
alkali-Ion (Li-Ion, Na-Ion), Pb, NiMH and combined chemistries EV modules and
batteries
Straßenfahrzeuge - Wiederaufladbare Batterien mit internem Speicher - Unmittelbare
Leistung von Modulen und Batterien für Elektrofahrzeuge mit Li-Ion, Pb, NiMH und
kombinierter Chemie
Véhicules routiers - Batteries rechargeables avec stockage interne d'énergie -
Performance des modules et batteries alcali-ion (Li-Ion, Na-Ion), Pb, NiMH et chimies
combinées pour véhicules électriques
Ta slovenski standard je istoveten z: prEN 18060
ICS:
29.220.99 Drugi členi in baterije Other cells and batteries
43.120 Električna cestna vozila Electric road vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2024
ICS
English Version
Road vehicles - Rechargeable batteries with internal
energy storage - Performance of alkali-Ion (Li-Ion, Na-Ion),
Pb, NiMH and combined chemistries EV modules and
batteries
Véhicules routiers - Batteries rechargeables avec Straßenfahrzeuge - Wiederaufladbare Batterien mit
stockage d'énergie interne - Performance instantanée internem Speicher - Unmittelbare Leistung von
des modules et batteries Li-Ion, Pb, NiMH et chimies Modulen und Batterien für Elektrofahrzeuge mit Li-Ion,
combinées pour véhicules électriques Pb, NiMH und kombinierter Chemie
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 301.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18060:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Abbreviated terms . 14
5 General requirements . 14
5.1 Prerequisites for performance tests . 14
5.2 Accuracy of measurement equipment and measured values . 15
6 Requirements . 15
6.1 Preconditioning cycles . 15
6.1.1 Purpose . 15
6.1.2 Test procedure . 15
6.2 Standard cycle (SC) . 16
6.2.1 Purpose . 16
6.2.2 Test procedure . 16
6.3 Capacity (in Ah) . 17
6.3.1 Purpose . 17
6.3.2 Test procedure . 17
6.3.3 Determination of capacity (in Ah) . 17
Ω
) . 18
6.4 Determination of internal resistance (in
6.5 Testing of partly charged DUT . 19
6.6 Determination of power (in W) . 19
6.7 Determination of energy round trip efficiency (in %) . 20
6.8 Determination of nominal power . 21
6.9 Beginning of life (BOL) full equivalent cycles (for expected lifetime determination)
................................................................................................................................................................... 21
7 Test report . 22
Annex A (normative) Simplified requirements for individual battery testing due to change
of status (status ‘reused’ and ‘remanufactured’) . 23
A.1 Preconditioning – Purpose . 23
A.2 Capacity (in Ah) . 23
A.2.1 Purpose . 23
A.2.2 Test procedure . 23
A.2.3 Determination of capacity (in Ah) . 24
Ω
A.3 Determination of internal resistance (in ) . 24
A.4 Testing of partly charged DUT . 24

A.5 Determination of power (in W) . 25
A.6 Determination of energy round trip efficiency (in %) . 25
Annex ZA (informative) Relationship between this European Standard and the requirements
of Regulation (EU) 2023/1542 of the European Parliament and of the Council of 12
July 2023 concerning batteries and waste batteries, amending Directive 2008/98/EC
and Regulation (EU) 2019/1020 and repealing Directive 2006/66/EC aimed to be
covered . 26
Bibliography . 28

European foreword
This document (prEN 18060:2024) has been prepared by Technical Committee CEN/TC 301 “Road
vehicles”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Introduction
European Commission published the standardization request M/579 to the European standardization
organisations as regards to performance and sustainability requirements for batteries.
Battery systems are an efficient energy storage system for electrically propelled vehicles. The
performance requirements for electric road vehicles battery systems are significantly different from
those batteries used for consumer electronics or stationary energy storage. The state of charge window
that is accessible for the vehicle application is defined by durability and safety requirements.
This document provides specific performance test procedures for EV battery systems, battery packs and
battery modules.
It enables vehicle manufacturers to choose test procedures to evaluate the characteristics of EV battery
systems, battery packs and battery modules for their specific requirements.
This document specifies test procedures for alkali-Ion (Li-Ion, Na-Ion), Pb, NiMH and combined
chemistries for EV battery systems, battery packs and battery modules to obtain performance values for
rated capacity, rated power, internal resistance, and energy round trip efficiency.
NOTE EV cells performance standard is under drafting in CLC/TC21X/WG 7.
1 Scope
This document describes the performance test procedures and calculation methods for alkali-ion (for
example Li-ion, Na-ion), Pb, NiMH and combined chemistries EV battery systems, battery packs and
battery modules. This document considers the most appropriate metric based on application for
electrical performance between different models/products on the market. It specifies performance test
procedures and calculation methods to obtain performance values for:
• rated capacity (in Ah);
• power (in W);
• internal resistance (in ꭥ);
• energy round trip efficiency (in %);
• expected lifetime (number of reference cycles).
The tests in this document are relevant for EV battery systems, battery packs and battery modules
intended for the following applications:
• motor vehicles, including M, N and O categories referred to in Article 2 of Regulation (EU) 2018/858
of the European Parliament and of the Council with traction battery;
• L-category vehicles referred to in Article 2 of Regulation EU 168/2013 of the European Parliament
and of the Council with traction battery of more than 25kg.
NOTE 1 Other chemistry can be included in the scope of this document.
NOTE 2 These procedures could be used for type testing of a model/product at begin of life (status ‘original’)
and for individual battery testing after change of status (status ‘reused’ and ‘remanufactured’).
These tests for parameters above are performed at component level outside the vehicle.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
battery
device delivering electrical energy generated by direct conversion of chemical energy, having internal or
external storage, and consisting of one or more non-rechargeable or rechargeable battery cells, modules
or of packs of them, including a battery that has been subject to preparing for re-use, preparing for
repurpose or repurposing, or remanufacturing
[SOURCE: regulation (EU) 2023/1542]
3.2
battery cell
basic functional unit in a battery constituted by electrodes, electrolyte, container, terminals and, if
applicable, se
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.