FprEN 16510-2-3
(Main)Residential solid fuel burning appliances - Part 2-3: Cookers
Residential solid fuel burning appliances - Part 2-3: Cookers
This Part 2-3 of EN 16510 is applicable to hand fired residential cookers whose primary function is to cook and whose secondary function is to provide heat into the space in which they are installed. Additionally, where fitted with a boiler, they also provide domestic hot water and/or central heating. These appliances may burn one or more types of the following solid fuels in accordance with the appliance manufacturer’s instructions:
- wood logs
- compressed untreated wood
- wood pellets
- solid mineral fuels
- peat briquettes.
This Part 2-3 of EN 16510 is not applicable to appliances with fan assisted combustion air or appliances that are mechanically fired.
This Part 2-3 of EN 16510 is to be used in conjunction with EN 16510-1 of which it is an integral part.
Häusliche Feuerstätten für feste Brennstoffe - Teil 2-3: Herde
Dieser Teil 2-3 der EN 16510 gilt für handbeschickte Herde, deren Hauptfunktion das Kochen und deren weitere Funktion die Beheizung des Aufstellungsraumes ist. Heizungsherde liefern zusätzlich Heizwasser und/oder dienen der Zentralbeheizung.
Diese Feuerstätten können entsprechend der Bedienungsanleitung des Herstellers einen oder mehrere der folgenden festen Brennstoffe verfeuern:
- Scheitholz;
- Holzbriketts;
- Holzpellets;
- feste mineralische Brennstoffe;
- Torfbriketts.
Dieser Teil 2-3 der EN 16510 gilt nicht für Feuerstätten mit Verbrennungsluftgebläse oder mechanisch beschickte Feuerstätten.
Dieser Teil 2-3 der EN 16510 ist in Verbindung mit EN 16510-1 anzuwenden, die Bestandteil dieser Norm ist.
Appareils de chauffage domestiques à combustible solide - Partie 2-3: Cuisinières
La présente Partie 2-3 de l'EN 16510 s'applique aux cuisinières domestiques alimentées manuellement dont la fonction principale est de cuire et la fonction secondaire de chauffer l’espace dans lequel elles sont installées. De plus, lorsqu’elles sont équipées d’un bouilleur, elles produisent également de l’eau chaude à usage domestique et/ou du chauffage central. Ces appareils peuvent utiliser des combustibles minéraux solides, des briquettes de lignite, des briquettes de tourbe, des bûches de bois naturelles ou reconstituées, ou plusieurs combustibles conformément aux instructions du fabricant.
La présente Partie 2-3 de l'EN 16510 ne s'applique pas aux appareils équipés d'un ventilateur pour l'alimentation en air de combustion ou aux appareils à alimentation mécanique.
Stanovanjske grelne naprave na trdna goriva - 2-3. del: Štedilniki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 16510-2-3:2013
01-marec-2013
Stanovanjske grelne naprave na trdna goriva - 2-3. del: Štedilniki
Residential solid fuel burning appliances - Part 2-3: Cookers
Häusliche Heizgeräte für feste Brennstoffe - Teil 2-3: Herde
Equipement de chauffage domestique - Partie 2-3 : Cuisinières
Ta slovenski standard je istoveten z: prEN 16510-2-3
ICS:
97.040.20 âWHGLOQLNLGHORYQLSXOWL Cooking ranges, working
SHþLFHLQSRGREQLDSDUDWL tables, ovens and similar
appliances
97.100.30 Grelniki na trdo gorivo Solid fuel heaters
oSIST prEN 16510-2-3:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 16510-2-3:2013
oSIST prEN 16510-2-3:2013
EUROPEAN STANDARD
DRAFT
prEN 16510-2-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2013
ICS 97.100.30 Will supersede EN 12815:2001
English Version
Residential solid fuel burning appliances - Part 2-3: Cookers
Equipement de chauffage domestique - Partie 2-3 : Häusliche Heizgeräte für feste Brennstoffe - Teil 2-3: Herde
Cuisinières
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 295.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16510-2-3:2013: E
worldwide for CEN national Members.
oSIST prEN 16510-2-3:2013
prEN 16510-2-3:2013 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Classification of appliances and system boundary for roomsealed appliances .4
5 Materials, design and construction .4
6 Safety requirements .6
7 Performance requirements .6
8 Appliance instructions .8
9 Evaluation of conformity .8
10 Marking .8
Annex A (normative) Test methods .9
Annex B (normative) Test fuels and recommended fuels. 20
Annex C (informative) Installation for roomsealed appliances . 21
Annex D (informative) Arrangement for measuring the leakage rate . 22
Annex E (normative) Measuring procedure for nitrogen oxides (NO ). 23
x
Annex F (normative) Measuring procedure for organic gaseous compounds (OGC) . 24
Annex G (normative) Measuring procedure for particulate matter (PM) . 25
Annex H (informative) Guideline for the characteristics to be taken into account in order to decide
on families of appliances . 26
Annex AA (normative) Browning chart for oven heating test . 27
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive . 28
oSIST prEN 16510-2-3:2013
prEN 16510-2-3:2013 (E)
Foreword
This document (prEN 16510-2-3:2013) has been prepared by Technical Committee CEN/TC 295 “Residential
solid fuel burning appliances”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12815:2001.
EN 13240:2001, EN 13229:2001, EN 12815:2001 and EN 12809:2001 will be totally superseded by EN 16510
series. The revision of these European Standards takes into account the comments received at their 5-year
review.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive 89/106/EEC, see informative Annex ZA, which is an integral part of this
document.
The structure of EN 16510, Residential solid fuel burning appliances, is as follows:
Part 1: General requirements and test methods;
Part 2-1: Roomheaters;
Part 2-2: Inset appliances including open fires;
Part 2-3: Cookers;
Part 2-4: Independent boilers – Nominal heat output up to 50 kW.
Principally it is possible to add further parts 2 at a later stage in order to cover other residential solid fuel
burning appliances such as pellet stoves or slow heat release appliances.
This Part 2-3 is to be used in conjunction with the latest edition of EN 16510-1 and its amendments. It was
established on the basis of prEN 16510-1:2013.
This Part 2-3 supplements or modifies the corresponding clauses in EN 16510-1, so as to convert that
publication into the European Standard: Residential solid fuel burning appliances – Requirements and test
methods for cookers.
When a particular subclause of Part 1 is not mentioned in this Part 2-3, that subclause applies as far as is
reasonable. When this Part 2-3 states "addition", "modification" or "replacement", the relevant text in Part 1 is
to be adapted accordingly.
NOTE The following numbering system is used:
subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those
in a replaced clause or subclause;
additional annexes are lettered AA, BB, etc.
oSIST prEN 16510-2-3:2013
prEN 16510-2-3:2013 (E)
1 Scope
This Part 2-3 of EN 16510 is applicable to hand fired residential cookers whose primary function is to cook
and whose secondary function is to provide heat into the space in which they are installed. Additionally, where
fitted with a boiler, they also provide domestic hot water and/or central heating. These appliances may burn
either solid mineral fuels, lignite briquettes, peat briquettes, natural or manufactured wood logs or be multi-fuel
in accordance with the appliance manufacturer's instructions.
This Part 2-3 of EN 16510 is not applicable to appliances with fan assisted combustion air or appliances that
are mechanically fired.
2 Normative references
prEN 16510-1:2013, Clause 2, is applicable.
3 Terms and definitions
prEN 16510-1:2013, Clause 3 is applicable.
4 Classification of appliances and system boundary for roomsealed appliances
prEN 16510-1:2013, Clause 4, is applicable.
5 Materials, design and construction
prEN 16510-1:2013, Clause 5, is applicable with the following modifications.
5.2.2.2.2 Nominal minimum wall thicknesses (steel)
Addition:
Differing from the requirement given in Table 2 for walls of water backed surfaced of the combustion chamber
in contact with burning fuel or products of combustion the minimum wall thickness for non-alloy steels is 4 mm
for cookers.
5.2.6 Ashpan and ash removal
prEN 16510-1:2013, 5.2.6, is applicable with the following modification.
Replacement of the 1st paragraph:
A means of removing ash residue from the appliance shall be provided. Where an ashpan is provided its
3 3
capacity shall be not less than 0,75 dm per kW nominal output for appliances without a boiler and 0,3 dm per
kW nominal output for appliances with a boiler whilst retaining sufficient space above to allow adequate
primary air - flow through the bottomgrate or firebed. If the ashpan resides in the appliance it shall locate in the
ashpit in such a way that it allows the free passage of primary air and in such a position that it does not
obstruct any primary air inlet control.
5.2.7 Bottomgrate
prEN 16510-1:2013, 5.2.7, is applicable with the following modification.
Replacement of the 1st paragraph:
The bottomgrate, excluding those with water - cooled firebars, shall be capable of being removed and shall be
so designed or marked as to ensure correct assembly. A de-ashing mechanism shall be fitted where fuels
other than wood are burned. The bottomgrate shall not become dislodged during the de-ashing process.
oSIST prEN 16510-2-3:2013
prEN 16510-2-3:2013 (E)
5.2.10 Firedoors and charging doors
prEN 16510-1:2013, 5.2.10, is not applicable.
Replacement of the whole subclause 5.2.10:
Firedoors and charging doors shall be designed to prevent accidental opening and to facilitate positive
closure. Door seals shall be either metal to metal or of flexible non-combustible material.
Means shall be provided to maintain the fit of any door sealed with flexible non-combustible material.
When open firedoors shall not obstruct the firebox opening and shall be capable of opening to an angle
greater than 90°.
If fitted, hotplate charging doors shall either be removable or capable of being opened to an angle greater
than 90°.
NOTE Designed air inlets around the periphery of the door(s) are permitted.
Addition of the following new subclause:
5.101 Additional requirements for cookers
5.101.1 Oven door
When open, side hinged oven doors shall not obstruct the oven opening and shall be capable of opening to an
angle greater than 90°.
When drop down doors are completely open, they shall form an angle of between 85° and 90° to the vertical
and remain in this position. When tested in accordance with A.4.101.5, the drop down door shall not sag by
more than 15 mm, and the cooker shall not tilt.
5.101.2 Hotplate and top plate
The top plate shall incorporate a metal or ceramic surface in the form of a hotplate. Part of the hotplate shall
be designed as a boiling plate area.
When the cooker is assembled in accordance with the appliance manufacturer’s installation instructions,
complete with any legs or plinth supplied as an integral part of the appliance, the height from the floor to the
cooking surface(s) shall be between 800 mm and 930 mm.
5.101.3 Main/additional ovens
Where a compartment or compartments are provided as an oven or ovens, their purpose shall be specified in
the appliance operating instructions.
The main oven and any additional oven shall be provided with at least two shelf runner positions.
When tested in accordance with the test method detailed in A.4.101.4, the angle of inclination of any oven
shelf when under load shall not exceed 10° from the horizontal.
5.101.4 Ashpit and ashpit cover/door
The ashpit shall be so designed that when the ashpan is in position it shall not restrict the primary air inlet.
The ashpit cover/door shall be designed to ensure that
its closure is not prevented by spilled residue material,
oSIST prEN 16510-2-3:2013
prEN 16510-2-3:2013 (E)
it cannot be accidentally dislodged,
when hot it can be handled safely with the tools provided,
the ashpit is of sufficient size to accommodate the ashpan.
5.101.5 Oven temperature indicators
For a cooker with an oven(s) to which an oven temperature indicator is fitted, the indicator shall be readable
without opening the oven door.
6 Safety requirements
prEN 16510-1:2013, Clause 6, is applicable.
7 Performance requirements
prEN 16510-1:2013, Clause 7, is applicable with the following modifications.
7.3 Efficiency
prEN 16510-1:2013, 7.3, is applicable with the following modification.
st
Addition after 1 paragraph:
The manufacturer’s declared efficiency value shall be equal to or exceed 70 %.
7.5 Recovery test
prEN 16510-1:2013, 7.5, is applicable with the following modification.
nd
Replacement of the 2 paragraph:
Recovery shall be deemed to be satisfactory if the refuel charge is visibly ignited under the test conditions
+2
described in A.4.8.4 within a time of 30 min with a fl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.