EN ISO 8836:2020
(Main)Suction catheters for use in the respiratory tract (ISO 8836:2019)
Suction catheters for use in the respiratory tract (ISO 8836:2019)
This document specifies dimensions and requirements for both open and closed suction catheters made of flexible materials and intended for use in suctioning of the respiratory tract.
Suction catheters intended for use with flammable anaesthetic gases or agents, lasers or electrosurgical equipment are not covered by this document.
NOTE For guidance on airway management during laser surgery of the upper airway, see ISO/TR 11991[4].
Absaugkatheter zur Verwendung im Atemtrakt (ISO 8836:2019)
Dieses Dokument legt Maße und Anforderungen an sowohl offene als auch geschlossene Absaugkatheter aus flexiblen Materialien zur Verwendung bei der Absaugung im Atemtrakt fest.
Absaugkatheter zur Verwendung mit brennbaren Anästhesiegasen oder Anästhesiemitteln, mit Lasern oder elektrochirurgischen Geräten sind nicht Gegenstand dieses Dokuments.
ANMERKUNG ISO/TR 11991 enthält einen Leitfaden zur Sicherung der Luftwege bei Laserchirurgie in den oberen Atemwegen [4].
Sondes d'aspiration pour les voies respiratoires (ISO 8836:2019)
Le présent document spécifie les dimensions et les exigences applicables aux sondes d'aspiration fermées, mais aussi ouvertes constituées de matériaux souples et destinées à une utilisation dans l'aspiration des voies respiratoires.
Les sondes d'aspiration destinées à une utilisation avec des gaz ou agents anesthésiques inflammables, des lasers ou des appareils électrochirurgicaux ne sont pas couvertes par le présent document.
NOTE Pour obtenir des recommandations relatives à la façon d'assurer la ventilation au cours d'opérations par laser des voies respiratoires supérieures, se reporter à l'ISO/TR 11991[4].
Aspiracijski katetri za čiščenje dihalnih poti (ISO 8836:2019)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2020
Nadomešča:
SIST EN ISO 8836:2015
Aspiracijski katetri za čiščenje dihalnih poti (ISO 8836:2019)
Suction catheters for use in the respiratory tract (ISO 8836:2019)
Absaugkatheter zur Verwendung im Atemtrakt (ISO 8836:2019)
Sondes d'aspiration pour les voies respiratoires (ISO 8836:2019)
Ta slovenski standard je istoveten z: EN ISO 8836:2020
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
11.040.25 Injekcijske brizge, igle in Syringes, needles an
katetri catheters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8836
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2020
EUROPÄISCHE NORM
ICS 11.040.10; 11.040.25 Supersedes EN ISO 8836:2014
English Version
Suction catheters for use in the respiratory tract (ISO
8836:2019)
Sondes d'aspiration pour les voies respiratoires (ISO Absaugkatheter zur Verwendung im Atemtrakt (ISO
8836:2019) 8836:2019)
This European Standard was approved by CEN on 24 June 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8836:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 8836:2020) has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment" in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2021, and conflicting national standards shall be
withdrawn at the latest by October 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8836:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8836:2019 has been approved by CEN as EN ISO 8836:2020 without any modification.
INTERNATIONAL ISO
STANDARD 8836
Fifth edition
2019-12
Suction catheters for use in the
respiratory tract
Sondes d'aspiration pour les voies respiratoires
Reference number
ISO 8836:2019(E)
©
ISO 2019
ISO 8836:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 8836:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 *General requirements . 3
5 Materials . 4
6 Design requirements . 4
6.1 General . 4
6.2 Size designations and dimensions . 4
6.3 Suction catheter tip . 5
6.4 *Suction catheter connector . . 6
6.5 Additional requirements for closed suction catheters . 7
6.5.1 General design. 7
6.5.2 Closed suction catheter manifold and connectors . 8
6.5.3 Protective sleeve . 9
6.5.4 *Suction control device . 9
6.5.5 Flushing system .10
6.5.6 T-piece port .10
6.6 Performance requirements .10
6.6.1 Security of construction .10
6.6.2 Shaft performance .10
6.6.3 Suction control device performance .11
6.6.4 *Leakage .11
6.6.5 *Resistance to flow .11
7 Requirements for suction catheters supplied sterile .11
8 Packaging .11
9 Information supplied by the manufacturer .11
9.1 General .11
9.2 Marking .12
9.3 Instructions for use .13
Annex A (informative) Rationale .14
Annex B (normative) Test method for security of attachment .17
Annex C (normative) Measurement of residual vacuum .18
Annex D (normative) *Method of testing leakage .20
Annex E (informative) Hazard identification for risk assessment .21
Bibliography .24
ISO 8836:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.