EN ISO 3183:2019
(Main)Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2019)
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2019)
This document specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries.
This document supplements API Spec 5L, 46th edition (2018), the requirements of which are applicable with the exceptions specified in this document.
This document is not applicable to cast pipe.
Erdöl- und Erdgasindustrie - Stahlrohre für Rohrleitungstransportsysteme (ISO 3183:2019)
Dieses Dokument legt Anforderungen für die Fertigung nahtloser und geschweißter Rohre für Rohrleitungstransportsysteme der Erdöl- und Erdgasindustrie nach zwei Produkt-Anforderungsstufen (PSL 1 und PSL 2) fest.
Dieses Dokument ist eine Ergänzung zu API Spec 5L, 46. Ausgabe (2018), deren Anforderungen mit der in diesem Dokument festgelegten Ausnahmen anzuwenden sind.
Dieses Dokument gilt nicht für gegossene Rohre.
Industries du pétrole et du gaz naturel - Tubes en acier pour les systèmes de transport par conduites (ISO 3183:2019)
Le présent document spécifie les exigences relatives à la fabrication de tubes en acier sans soudure et soudés utilisés dans des systèmes de transport par conduites dans les industries du pétrole et du gaz naturel et répondant à deux niveaux de spécifications de produit (PSL 1 et PSL 2).
Le présent document complète la spécification API 5L, 46e édition (2018), dont les exigences sont applicables sauf exceptions spécifiées dans le présent document.
Le présent document ne s'applique pas aux tuyaux en fonte.
Industrija za predelavo nafte in zemeljskega plina - Jeklene cevi za cevovodni transportni sistem (ISO 3183:2019)
Ta dokument določa zahteve za izdelavo dveh ravni specifikacije izdelkov (PSL 1 in PSL 2) nevarjenih in varjenih jeklenih cevi, ki se uporabljajo v cevovodnih transportnih sistemih v industriji za predelavo nafte in zemeljskega plina. Ta dokument dopolnjuje 46. izdajo specifikacij API 5L (2018), katerih zahteve se uporabljajo za izjeme, določene v tem dokumentu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN ISO 3183:2013
SIST EN ISO 3183:2013/A1:2018
Industrija za predelavo nafte in zemeljskega plina - Jeklene cevi za cevovodni
transportni sistem (ISO 3183:2019)
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems
(ISO 3183:2019)
Erdöl- und Erdgasindustrie - Stahlrohre für Rohrleitungstransportsysteme (ISO
3183:2019)
Industries du pétrole et du gaz naturel - Tubes en acier pour les systèmes de transport
par conduites (ISO 3183:2019)
Ta slovenski standard je istoveten z: EN ISO 3183:2019
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3183
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 75.200; 77.140.75 Supersedes EN ISO 3183:2012
English Version
Petroleum and natural gas industries - Steel pipe for
pipeline transportation systems (ISO 3183:2019)
Industries du pétrole et du gaz naturel - Tubes en acier Erdöl- und Erdgasindustrie - Stahlrohre für
pour les systèmes de transport par conduites (ISO Rohrleitungstransportsysteme (ISO 3183:2019)
3183:2019)
This European Standard was approved by CEN on 19 February 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3183:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3183:2019) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in
collaboration with Technical Committee CEN/TC 459/SC 10 “Steel tubes, and iron and steel fittings” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3183:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3183:2019 has been approved by CEN as EN ISO 3183:2019 without any modification.
INTERNATIONAL ISO
STANDARD 3183
Fourth edition
2019-10
Petroleum and natural gas
industries — Steel pipe for pipeline
transportation systems
Industries du pétrole et du gaz naturel — Tubes en acier pour les
systèmes de transport par conduites
Reference number
ISO 3183:2019(E)
©
ISO 2019
ISO 3183:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 3183:2019(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
th
4 Supplements to API Spec 5L, 46 edition (2018) . 2
4.1 General requirements . 2
4.2 PSL 2 pipe for European onshore natural gas transmission pipelines . 2
4.3 Information to be supplied by the purchaser . 2
4.4 Marking . 2
4.4.1 General. 2
4.4.2 Pipe marked as ISO 3183 . 3
4.4.3 Pipe marked as API 5L (with monogram option) and the additional
marking of “ISO 3183” . 4
Annex A (normative) PSL 2 pipe ordered for European onshore natural gas transmission
pipelines . 5
Bibliography .23
ISO 3183:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to
conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www .iso .org/iso/foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 67, Materials, equipment
and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 2,
Pipeline transportation systems.
This fourth edition cancels and replaces the third edition (ISO 3183:2012), which has been technically
revised. It also incorporates the Amendment (ISO 3183:2012/Amd.1:2017).
th
This document supplements API Spec 5L, 46 edition (2018).
The technical requirements of this document and API Spec 5L used to be identical (except for the
inclusion of Annex M in the ISO publication). In the meantime API Spec 5L has been technically revised
th
as API Spec 5L, 46 edition (2018). The purpose of this document is to bring it up to date, by referencing
the current edition of API Spec 5L and including supplementary content.
The main changes compared to the previous edition are as follows:
— Technical changes now incorporated by normative reference to API Spec 5L have been made in the
API Spec 5L subclauses addressing
— weld seams (API Spec 5L, 8.8.2 clarifies heat treatment),
— tolerances for straightness (API Spec 5L, 9.11.3.4b and J.6.4 pipe end tolerances tightened),
— end squareness (API Spec 5L, 9.12.6 defined in detail),
— impact test pieces (API Spec 5L, Table 22 test piece size table corrected),
— location of hardness tests (API Spec 5L, Figures H.1 and J.1 weld centre line for HFW detailed),
— welded jointers (API Spec 5L, Annex M fit up and geometry, marking & NDT addressed),
— a new annex N has been added for PSL 2 pipe ordered for applications requiring longitudinal
plastic strain capacity, and
iv © ISO 2019 – All rights reserved
ISO 3183:2019(E)
— changes on order of annexes.
— Annex M of the previous edition of this document, i.e. ISO 3183:2012/Amd 1:2017, for PSL 2 pipe
ordered for European onshore natural gas transmission pipelines, is now provided as Annex A.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 3183:2019(E)
Introduction
th
This document was originally developed by harmonizing the requirements of API Spec 5L, 44 edition
(2007) and the second edition of this document, i.e. ISO 3183:2007. This continued to be the case for
th
the third edition of this document, i.e. ISO 3183:2012 and API Spec 5L, 45 edition (2012), in which
clarification and additional technical requirements were added.
vi © ISO 2019 – All rights reserved
INTERNATIONAL STANDARD ISO 3183:2019(E)
Petroleum and natural gas industries — Steel pipe for
pipeline transportation systems
1 Scope
This document specifies requirements for the manufacture of two product specification levels (PSL
1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the
petroleum and natural gas industries.
th
This document supplements API Spec 5L, 46 edition (2018), the requirements of which are applicable
with the exceptions specified in this document.
This document is not applicable to cast pipe.
2 Normative references
The following documents are referred to in the text in such a way
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.