EN ISO 12671:2021
(Main)Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2021)
Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2021)
This document specifies how the symbolic representation of thermally sprayed coatings is indicated on drawings.
Thermisches Spritzen - Thermisch gespritzte Schichten - Symbolische Darstellung in Zeichnungen (ISO 12671:2021)
Dieses Dokument legt fest, wie die symbolische Darstellung einer thermisch gespritzten Schicht in Zeichnungen angewendet wird.
Projection thermique - Revêtements appliqués par projection thermique - Représentation symbolique sur les dessins (ISO 12671:2021)
Le présent document spécifie la manière de faire figurer sur les dessins la représentation symbolique des revêtements obtenus par projection thermique.
Vroče brizganje - Vroče brizgane prevleke - Simbolično prikazovanje na risbah (ISO 12671:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2021
Nadomešča:
SIST EN ISO 12671:2014
Vroče brizganje - Vroče brizgane prevleke - Simbolično prikazovanje na risbah
(ISO 12671:2021)
Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings
(ISO 12671:2021)
Thermisches Spritzen - Thermisch gespritzte Schichten - Symbolische Darstellung in
Zeichnungen (ISO 12671:2021)
Projection thermique - Revêtements appliqués par projection thermique - Représentation
symbolique sur les dessins (ISO 12671:2021)
Ta slovenski standard je istoveten z: EN ISO 12671:2021
ICS:
01.080.30 Grafični simboli za uporabo v Graphical symbols for use on
risbah, diagramih, načrtih, mechanical engineering and
zemljevidih v strojništvu in construction drawings,
gradbeništvu ter v ustrezni diagrams, plans, maps and in
tehnični proizvodni relevant technical product
dokumentaciji documentation
25.220.20 Površinska obdelava Surface treatment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 12671
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2021
EUROPÄISCHE NORM
ICS 01.080.30; 25.220.20 Supersedes EN ISO 12671:2014
English Version
Thermal spraying - Thermally sprayed coatings - Symbolic
representation on drawings (ISO 12671:2021)
Projection thermique - Revêtements appliqués par Thermisches Spritzen - Thermisch gespritzte Schichten
projection thermique - Représentation symbolique sur - Symbolische Darstellung in Zeichnungen (ISO
les dessins (ISO 12671:2021) 12671:2021)
This European Standard was approved by CEN on 20 February 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12671:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 12671:2021) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 240 “Thermal
spraying and thermally sprayed coatings” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2021, and conflicting national standards shall
be withdrawn at the latest by October 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12671:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 12671:2021 has been approved by CEN as EN ISO 12671:2021 without any modification.
INTERNATIONAL ISO
STANDARD 12671
Second edition
2021-04
Thermal spraying — Thermally
sprayed coatings — Symbolic
representation on drawings
Projection thermique — Revêtements appliqués par projection
thermique — Représentation symbolique sur les dessins
Reference number
ISO 12671:2021(E)
©
ISO 2021
ISO 12671:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 12671:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Symbols . 1
6 Position of the symbols on drawings . 2
7 Designation of a thermally sprayed coating . 2
8 Instructions when using a separate parts’ list. 4
9 Instructions when the use of the spray process is protected by a patent .4
10 Representation and dimensioning . 4
11 Supplementary instructions . 4
12 Examples . 5
Bibliography . 7
ISO 12671:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 240, Thermal spraying and thermally sprayed coatings, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 12671:2012), which has been technically
revised. The main changes compared with the previous edition are as follows:
— the designation examples and figures have been updated in accordance with the latest thermal
spray terminology and material standards (see ISO 14917, ISO 14919 and ISO 14232-1).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
INTERNATIONAL STANDARD ISO 12671:2021(E)
Thermal spraying — Thermally sprayed coatings —
Symbolic representation on drawings
1 Scope
This document specifies how the symbolic representation of thermally sprayed coatings is indicated on
drawings.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 General
Coatings may be indicated with the general recommendations for technical drawings. To apply this
symbolic representation will make sense in cases where the thermally sprayed coating is very thin
and/or can be built up by several dissimilar coatings one upon another.
The symbolic representation shall clearly give all the necessary indications regarding the specific
coating to be obtained without over-burdening the drawing with notes or showing an additional view
or detail enlargement.
This symbolic representation includes an elementary symbol and one or more supplementary symbols
and further complementary indications.
If a large number of instructions for producing the coating have to be mentioned, it is recommended to
indicate the specific instructions on the drawing or to define them in a separate parts’ list, if applicable
(see Figures 6 and 7).
5 Symbols
The elementary symbol shall indicate that this process deals with thermal spraying.
The following information shall be given by supplementary symbols:
— type of coating (bond or top coat);
— the spraying process and subsequent treatments.
The following requirements may be defined by further additional instructions:
— the coating thickness needed or the final coating thickness machined;
— the spray material to be used;
ISO 12671:2021(E)
— the surface condition;
— post-treatments of coating;
— a technical specification that defines the requirements necessary to complete the coating.
6 Position of the symbols on drawings
The complete symbol shall contain:
— the designation of the coating (outside the outline of the component);
— an arrow line;
— a reference line (continuous line) with the elementary symbol above it;
— instructions concerning the mode of coating, spraying process, coating thickness, spray material,
surface condition and post-treatments, if applicable.
The arrow lin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.