EN 12697-37:2022
(Main)Bituminous mixtures - Test methods - Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for Hot-Rolled-Asphalt (HRA)
Bituminous mixtures - Test methods - Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for Hot-Rolled-Asphalt (HRA)
This document describes a hot sand test method for determining the condition of the binder on coated chippings for use with hot rolled asphalt (HRA) surface course.
Asphalt - Prüfverfahren - Teil 37: Prüfung des Haftvermögens eines Bindemittels auf vorumhülltem Splitt für Hot-Rolled-Asphalt (HRA) mittels heißem Sand
Dieses Dokument legt ein Prüfverfahren mit heißem Sand zur Bestimmung des Zustandes eines Bindemittels auf umhülltem Splitt für das Aufbringen auf Deckschichten aus Hot-Rolled-Asphalt (HRA) fest.
Mélanges bitumineux - Méthodes d’essai - Partie 37 : Essai au sable chaud pour l’adhérence du liant sur des gravillons pré-enrobés pour Hot-Rolled Asphalt (HRA)
Le présent document décrit une méthode d’essai au sable chaud pour déterminer l’état du liant sur des gravillons pré-enrobés utilisés sur les surfaces de chaussées en Hot Rolled Asphalt (HRA).
Bitumenske zmesi - Preskusne metode - 37. del: Preskus sprijemanja veziva s posipom iz drobirja za asfaltiranje z vročim peskom (HRA)
Ta dokument opisuje preskusno metodo z vročim peskom za ugotavljanje stanja veziva v posipu iz drobirja za uporabo pri površinskem asfaltiranju z vročim peskom (HRA).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2022
Nadomešča:
SIST EN 12697-37:2004
Bitumenske zmesi - Preskusne metode - 37. del: Preskus sprijemanja veziva s
posipom iz drobirja za asfaltiranje z vročim peskom (HRA)
Bituminous mixtures - Test methods - Part 37: Hot sand test for the adhesivity of binder
on pre-coated chippings for Hot-Rolled-Asphalt (HRA)
Asphalt - Prüfverfahren - Teil 37: Prüfung des Haftvermögens eines Bindemittels auf
vorumhülltem Splitt für Hot-Rolled-Asphalt (HRA) mittels heißem Sand
Mélanges bitumineux - Méthodes d’essai - Partie 37 : Essai au sable chaud pour
l’adhérence du liant sur des gravillons pré-enrobés pour Hot-Rolled Asphalt (HRA)
Ta slovenski standard je istoveten z: EN 12697-37:2022
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12697-37
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2022
EUROPÄISCHE NORM
ICS 93.080.20 Supersedes EN 12697-37:2003
English Version
Bituminous mixtures - Test methods - Part 37: Hot sand
test for the adhesivity of binder on pre-coated chippings
for Hot-Rolled-Asphalt (HRA)
Mélanges bitumineux - Méthodes d'essai - Partie 37 : Asphalt - Prüfverfahren - Teil 37: Prüfung des
Essai au sable chaud pour l'adhérence du liant sur des Haftvermögens eines Bindemittels auf vorumhülltem
gravillons pré-enrobés pour Hot-Rolled Asphalt (HRA) Splitt für Hot-Rolled-Asphalt (HRA) mittels heißem
Sand
This European Standard was approved by CEN on 21 February 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12697-37:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Materials . 5
6 Apparatus . 6
7 Sampling and preparation of test portion . 6
7.1 Sampling . 6
7.2 Preparation of test portion . 6
8 Procedure. 7
9 Calculation an expression of results . 8
10 Test report . 8
11 Precision . 8
European foreword
This document (EN 12697-37:2022) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2022, and conflicting national standards shall be withdrawn
at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12697-37:2003.
The main changes compared to the previous edition are listed below:
— the title no longer refers to hot mix asphalt;
— the title completed with “Hot-Rolled Asphalt”. The abbreviation “HRA” placed within brackets;
— general editorial update according to current standard template;
— European Foreword, deletion of paragraph “The applicability of this European Standard is described in
prEN 13108-4”;
— deletion of reference to EN 13043. Correction of titles for EN 12697-27 and EN 12697-28;
— Clause 3, deletion of terms and definitions 3.1 to 3.9. Terms and definitions given in EN 12697-27 and
EN 12697-28 are applied in relevant paragraphs;
— Clause 4, revision of NOTE to normal text;
— Clause 5, completion of left column heading in Table 1 to read “Test sieve aperture size”;
— 6.2, replacement of “accuracy” with “maximum permissible error”;
— 6.4, replacement of “accuracy” with “maximum permissible error”;
— 6.5, replacement of sieve “350 mm” with sieve “300 mm”;
— Clause 7, alteration of title to read “Sampling and preparation of test portions”.
— 7.1, alteration of title to read “Sampling”. Clarification of paragraph;
— 7.2, alteration of title to read “Preparation of test portion”. Clarification of paragraph;
— 7.2, reference to EN 12697-28:2000, 4.5 deleted;
— 7.3 to 7.12, renumbered to 8.1 to 8.10;
— 7.13, deletion of paragraph. NOTE 1 and NOTE 2 amended to normal text and placed under 8.10;
— Clause 8, alteration of title to read “Procedure”. Former Clause 8 renumbered to Clause 9;
— 8.1 (7.3 in previous version), correction of description of sieve sizes. Unit changed to “mm”;
— 8.6 (7.8 in previous version), deletion of superfluous text “ensuring that the sand temperature is not less
than 100 °C;
— 8.7 (7.9 in previous version), correction of description of sieve sizes. Unit changed to “mm”;
— 8.10 (7.13 in previous version), NOTE 1 and NOTE 2 amended to normal text”;
— Clause 9 (Clause 8 in previous version), alteration of title to read “Calculation and expression of results”;
— 9.1 (8.1 in previous version), equations adjusted and completed with keys and numbered;
— 9.2, (8.2 in previous version), equations adjusted and completed with keys and numbered;
— Clause 10 (Clause 9 in previous version), revision of the order and data to be reported;
— Clause 11, renumbered from “Clause 10” to “Clause 11”;
— Bibliograhy, deletion of references to prEN 13108-4 and prEN 12697-38.
A list of all parts in the EN 12697 series can be found on the CEN website.
Any feedback and questions on this document should be directed to the users’ national standards body. A
complete listing of these bodies can be found
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.