EN ISO 10360-4:2000
(Main)Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring mode (ISO 10360-4:2000)
Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring mode (ISO 10360-4:2000)
Migrated from Progress Sheet (TC Comment) (2000-07-10): Crash 1996: No forecast possible!
Geometrische Produktspezifikation (GPS) - Annahmeprüfung und Bestätigungsprüfung für Koordinatenmessgeräte (KMG) - Teil 4: KMG in Scanningmodus (ISO 10360-4:2000)
Dieser Teil von ISO 10360 legt die Annahmeprüfung zur Bestätigung der vom Hersteller genannten Leistung eines Koordinatenmeßgerätes fest, das im Scanningmodus angewendet wird. Sie legt auch die Bestätigungsprüfung fest, die es dem Anwender ermöglicht, die Leistung eines im Scanningmodus angewendeten KMG regelmäßig zu bestätigen. Die in diesem Teil von ISO 10360 beschriebene Annahmeprüfung und Bestätigungsprüfung ist nur für KMG im Scanningmodus anwendbar, und zwar mit beliebigen Arten von berührenden Meßköpfen.
Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) - Partie 4: MMT utilisées en mode de mesure par scanning (ISO 10360-4:2000)
La présente partie de l'ISO 10360 spécifie l'essai de réception qui vérifie que les performances des machines à mesurer tridimensionnelles (MMT) utilisées en mode de mesure par scanning sont conformes à ce qui est spécifié par le fabricant. Elle spécifie aussi l'essai de vérification périodique qui permet à l'utilisateur de vérifier périodiquement les performances des MMT utilisées en mode de mesure par scanning.L'essai de réception et l'essai de vérification périodique décrits dans la présente partie de l'ISO 10360 s'appliquent uniquement aux MMT pouvant réaliser des scannings en utilisant tout type de systèmes de palpage à contact.
Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring mode (ISO 10360-4:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2000
Geometrical Product Specifications (GPS) - Acceptance and reverification tests for
coordinate measuring machines (CMM) - Part 4: CMMs used in scanning
measuring mode (ISO 10360-4:2000)
Geometrical Product Specifications (GPS) - Acceptance and reverification tests for
coordinate measuring machines (CMM) - Part 4: CMMs used in scanning measuring
mode (ISO 10360-4:2000)
Geometrische Produktspezifikation (GPS) - Annahmeprüfung und Bestätigungsprüfung
für Koordinatenmessgeräte (KMG) - Teil 4: KMG in Scanningmodus (ISO 10360-4:2000)
Spécification géométrique des produits (GPS) - Essais de réception et de vérification
périodique des machines a mesurer tridimensionnelles (MMT) - Partie 4: MMT utilisées
en mode de mesure par scanning (ISO 10360-4:2000)
Ta slovenski standard je istoveten z: EN ISO 10360-4:2000
ICS:
17.040.30 Merila Measuring instruments
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 10360-4
First edition
2000-03-15
Geometrical Product Specifications
(GPS) — Acceptance and reverification
tests for coordinate measuring machines
(CMM) —
Part 4:
CMMs used in scanning measuring mode
Spécification géométrique des produits (GPS) — Essais de réception et de
vérification périodique des machines à mesurer tridimensionnelles
(MMT) —
Partie 4: MMT utilisées en mode de mesure par scanning
Reference number
ISO 10360-4:2000(E)
©
ISO 2000
ISO 10360-4:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
ISO 10360-4:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Requirements for metrological characteristics.2
4.1 Error of indication.2
4.2 Time for scanning test .2
4.3 Environmental conditions.2
4.4 Stylus system.2
4.5 Operating conditions.3
5 Acceptance test and reverification test.3
5.1 General.3
5.2 Principles.3
5.3 Measuring equipment.4
5.4 Procedure .4
5.5 Obtention of test results .5
6 Compliance with specifications .5
6.1 Acceptance test .5
6.2 Reverification test.6
7 Applications .6
7.1 Acceptance test .6
7.2 Reverification test.6
7.3 Interim check.7
Annex A (informative) Interim check.8
Annex B (informative) Workpiece related influences .9
Annex C (informative) Relation to the GPS matrix model.10
Bibliography.12
ISO 10360-4:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 10360 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 10360-4 was prepared by Technical Committee ISO/TC 213, Dimensional and
geometrical product specifications and verification.
ISO 10360 consists of the following parts, under the general title Geometrical Product Specifications (GPS) —
Acceptance and reverification tests for coordinate measuring machines (CMM):
� Part 1: Vocabulary
� Part 2: CMMs used for measuring linear dimensions
� Part 3: CMMs with the axis of a rotary table as the fourth axis
� Part 4: CMMs used in scanning measuring mode
� Part 5: CMMs using multiple stylus probing systems
� Part 6: Estimation of errors in computing Gaussian associated features
Annexes A, B and C of this part of ISO 10360 are for information only.
iv © ISO 2000 – All rights reserved
ISO 10360-4:2000(E)
Introduction
This part of ISO 10360 is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO/TR 14638). It influences link 5 of the chains of standards on size, distance, radius, angle,
form, orientation, location, run-out and datums.
For more detailed information on the relationship of this part of ISO 10360 to other standards and the GPS matrix
model, see annex C.
The acceptance test and reverification test of this part of ISO 10360 are applicable only to a CMM that is capable of
being used in a scanning measuring mode and may be used to determine the form of a surface or the parameters
of an associated feature.
The tests specified in this part of ISO 10360 are performed in addition to the size measuring test according to
ISO 10360-2, which are conducted without the use of scanning, and are designed to assess the performance of a
CMM used in a scanning measuring mode. It is normally not useful to isolate the scanning probing errors from
other sources of machine error.
INTERNATIONAL STANDARD ISO 10360-4:2000(E)
Geometrical Product Specifications (GPS) — Acceptance and
reverification tests for coordinate measuring machines (CMM) —
Part 4:
CMMs used in scanning measuring mode
1 Scope
This part of ISO 10360 specifies the acceptance test which verifies that the performance of a CMM used in
scanning measuring mode is as stated by the manufacturer. It also specifies the reverification test which enables
the user to periodically reverify the performance of a CMM used in scanning measuring mode.
The acceptance test and reverification test described in this part of ISO 10360 are applicable only to CMMs
capable of performing scannings using any type of contacting probing system(s).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 10360. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 10360 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
1)
ISO 10360-1:— , Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate
measuring machines (CMM) — Part 1: Vocabulary.
ISO 14253-1:1998, Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with specifications.
International Vocabulary of Basic and General Terms in Metrology (VIM). BIPM, IEC, IFCC, ISO, IUPAC, IUPAP,
OIML, 2nd edition, 1993.
3 Terms and definitions
For the purposes of this part of ISO 10360, the terms and definitions given in ISO 10360-1, ISO 14253-1 and VIM
apply.
1) To be published.
ISO 10360-4:2000(E)
4 Requirements for metrological characteristics
4.1 Error of indication
The scanning probing error(s), Tij, shall not exceed the maximum permissible scanning probing error(s), MPE ,as
Tij
stated by:
� the manufacturer, in case of acceptance tests;
� the user, in case of reverification tests.
The scanning probing error(s), Tij, and the maximum permissible scanning probing error(s), MPE , are expressed
Tij
in micrometres.
4.2 Time for scanning test
The time for scanning test, �, shall not exceed the maximum permissible time for scanning test, MPT , as stated
�
by:
� the manufacturer, in case of acceptance tests;
� the user, in case of reverification tests.
The time for scanning test, �, and the maximum permissible time for scanning test, MPT , are expressed in
�
seconds.
4.3 Environmental conditions
Limits to be respected for permissible environmental conditions such as temperature conditions, air humidity and
vibration at site of installation that influence the measurements shall be specified by:
� the manufacturer, in case of acceptance tests;
� the user, in case of reverification tests.
In both case
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.